Drive ASB-2109 Product manual

ASB-2109 & ASB-2709V Chair Belts
WARNING: Failure to comply with warning may result in injury or death. This device is not suitable for all individuals. Other devices may be required.
This device is not a substitute for visual monitoring by caregiver. The manufacturer does not claim that this device will stop elopement and/or stop
falls.This device is designed to augment caregivers’comprehensive resident mobility management program. THIS DEVICE IS NOT DESIGNED
TO RESTRAIN OR HOLD INDIVIDUALS IN POSITION IN THEIR CHAIRS. Test this device before each use. Read the instructions and Legal
Disclaimer.
The Drive ASB-2109 andASB-2109V Chair Belts are designed to be installed by the end user. As such, it is the entire responsibility of the
buyer to insure that the system is properly installed and tested. Further, the system is not designed to replace good caregiving
practices including, but not limitedto:
A.) Direct patient supervision
C.) Testing of the system before each use
WHERE PERMISSIBLE, IT IS THE SELLER’S INTENTTO LIMIT ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO
REFUND OF THE PURCHASE PRICE OR REPLACEMENT OF THE GOODS. SELLER DISCLAIMS ANY LIABILITY FOR COMPENSATORY OR OTHER DAMAGES
ARISING OUT OF THE USE OF THE GOODS.
WARNING: The manufacturer does not claim that this device will stop elopement and/or stop falls.This device is designed to augment caregivers’
comprehensive resident mobility management program. This product is to be used by a licensed caregiver only.
Limited Warranty: Seller warrants that the goods sold will be free from defects of workmanship and manufacturing, for a period of one year from
the date of sale. Other than this limited warranty, seller makes no express or implied warranties. Except for this limited warranty, NO EXPRESS OR
IMPLIED WARRANTIES ARE GIVEN AND NO AFFIRMATION OF SELLER, BY WORDS OR ACTION, WILL CONSTITUTE A WARRANTY. THE GOODS BEING
PURCHASED ARE BEING SOLD ON A“WITH ALL FAULTS”BASIS. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE GOODS IS WITH THE
BUYER. SHOULD THE GOODS PROVE DEFECTIVE FOLLOWING THEIR PURCHASE, THE BUYER, AND NOT THE MANUFACTURER, DISTRIBUTOR OR RETAILER,
ASSUMES THE ENTIRE COST OF ALL NECESSARY INSTALLATION, SERVICING OR REPAIRS.
Seat Belts
SEAT BELT PLACEMENT
• Unscrew one screw on either side of wheelchair that holds the seat in place.
• Attach the seat belt to wheelchair by lining up the grommet holes on seat
belt with the screw holes. Re-insert screws through both seat belt and
wheelchair to hold seat belt in place. Make sure the screws are tightened.
• Adjust the seat belt to the desired length using the black buckle that holds
the adjustment strap in place.
•Connect the seat belt cord to the monitor.
• Place the monitor out of reach of the resident. Suitable mounting
locations include the back of wheelchair, or on the chair handle so that
the resident cannot tamper with the monitor.
TEST THE SYSTEM
•
now active.The alert will sound whenever the seat belt is unbuckled.
•When the alert is activated, press the“Reset”button on front of the
monitor to silence the alert or use the Caregiver Key, depending on your
reset setting. The status light on front of monitor will blink when the
seat belt is plugged into the monitor and buckled.
ASB-2109 & ASB-2109V
Chair Belts
Non-Restraint Chair Belts
for use with Smart Caregiver
Fall/Mobility Monitors
Installation and Use Instructions
TL-2109_TL-2109V 1-14
Drive Medical Design & Manufacturing
99 Seaview Boulevard, Port Washington, NY 11050
www.drivemedical.com
Need Set-up Help? [phone]

Unscrew one screw on either side of the wheelchair that holds the
seat in place.
Attach seat belt to the chair by lining up the grommet holeswith
the screw holes. Re-insert screws through both the seat belt and
the chair securing the seat belt in place.
Adjust the seat belt to the desired length by
routing the strap through the buckle as shown
in Figs A-C.
Quick Start Instructions ASB-2109 & ASB-2109V
Need Set-up Help? [phone]
Seat Belt Installation
2
4
Mount the Fall Monitor
5Test the System
now active.The monitor will sound the alert whenever the Seat
Belt is unfastened.
When the monitor is activated press the“Reset”button. This will
shut down the alerting mode.
3
Mount the monitor out of reach of the resident. Suitable
mounting location is the back of wheelchair, so that the resident
cannot tamper with monitor or reach the“Reset”button.
Connect the Seat Belt to
the Fall Monitor
A.
B.
A. Route the strap through
the buckle as shown
C. Pull the end of the
strap to tighten
B. Strap routed correctly
before tightening
Seat Belt Closed Seat Belt Opened
Bottom of
monitor
Pinch the cord together
and route it through
the strain relief recess.
Plug the cord
into the monitor.
For more information about the
Caregiver Key™, and how it can be used
in your facility’s Fall Assessment Program
call 866-621-4933
Resetting the Monitor/ Tamper Proof ™Mode with Caregiver Key™(Optional)
“Reset Button ON”Mode
Press the Reset button to reset the
monitor.
“Reset Button OFF, Use Caregiver Key™ To Turn OFF”Mode.
Place the Caregiver Key™ over the red dot to reset the monitor.
Safety Auto Reset™
Pad
Lost
Low
Battery
Monitor Status
Active When Blinking
Pad and Monitor
Reset
SS
aa
ff
ee
ffeff
tt
y Auy Au
tty Autt
tt
oo
ttott
RR
ee
ss
eesee
et™et™
PP
adad
LL
ostost
LL
oo
ww
BB
aa
tt
tt
ee
rr
yy
MoniMoni
tt
or Stor St
aa
tustus
AA
cc
titi
vv
ee
WW
hen Blinhen Blin
kk
inging
PP
ad and Moniad and Moni
tt
oror
Safety Auto Reset™
Pad
Lost
Low
Battery
Monitor Status
Active When Blinking
Pad and Monitor
Reset
SS
aa
ff
ee
ffeff
tt
y Auy Au
tty Autt
tt
oo
ttott
RR
ee
ss
eesee
et™et™
PP
adad
LL
ostost
LL
oo
ww
BB
aa
tt
tt
ee
rr
yy
MoniMoni
tt
or Stor St
aa
tustus
AA
cc
titi
vv
ee
WW
hen Blinhen Blin
kk
inging
PP
ad and Moniad and Moni
tt
oror
Refer to User Instructions before changing this setting.
Reset Button-
ON
Reset Button OFF
Use Caregiver Key
To Turn OFF
6V DC 300mA MAX
-
Install
Batteries
1
The battery compartment
door is secured with the
included Phillips-head screw
Alert Volume
Adjustment
Tone
Adjustment
Alert Delay
Adjustment
Warning: Failureto comply with warning may result in injury or death. Thisdevice is not suitable for all individuals. Other
devices may be required.This device is not a substitute for
visual monitoring by caregiver.Sensor pad fall monitors are
user.The manufacturer does not claim that this device will
stop elopement and/or stop falls.This device is designed to
agument caregivers comprehensiveresident mobility
management program.Test this device before each use.
Read the instructions and legal disclaimer. Read Instructions Before Use: Battery not included. Use 3 x AA alkaline Batteries.
Set Up: Plug sensor pad into the fall monitor.Apply pressure to
the sensor pad to test the system.The monitor will emit two
beeps, indicating that the system is working.The Monitor Status LED will blink every 3 seconds when the system is
activated and operating properly.
Delay
2sec 1sec 0sec3 2 1 Dcrease/Increase
Volume
Tone
Close battery door and secure
it with small Philips-head
screw.
Place monitor back into its
plastic protective boot.
Drive Medical Design & Manufacturing el: 866-371-2266T | www.drivemedical.com
Caregivers can choose to reset the
CordLess® Monitor in either of two ways:
“Reset Switch ON”: Pressing the Reset
button on the front of the monitor.
“Reset Switch OFF”: Placing the optional
Caregiver Key over the red dot on the front
of the monitor.
Option 2 allows only the caregiver to reset
the monitor.
See switch on side of the monitor to select
the monitor of your choice.
For more information about the Caregiver
Key™ and how it can be used in your facility’s
Fall Risk Assessment Program call
866-621-4933