DS Services of America Pure Water Dispenser 300m Series User manual

1. Turn o the hot tank heater switch on the back of the dispenser and unplug your unit (Fig 1).
Let the unit stand for one hour before cleaning to allow the hot tank to cool.
2. Remove the water bottle and drain the water reservoir by dispensing water through the hot
and cold spigots.
3. Clean the cabinet, bottle receptacle and spigots with 70% rubbing alcohol or disinfecting
wipes. Vacuum or wipe the grill on the back of the dispenser to remove any dust.
4. Clean the drip tray and grill by emptying the tray and cleaning the tray and grill with
dishwashing soap or by placing them on the top rack of the dishwasher (Fig 2).
5. Remove the no-spill dispenser insert.
(Note that the no-spill dispenser insert
is designed to t tightly in the reservoir
and will require force to remove.)
– Begin by inserting a nger into the
notch in the dispenser insert and
prying up to reveal a gap (Fig 3a).
– Spray rubbing alcohol around the
no-spill insert and allow it to seep in
1-2 minutes to loosen the seal (Fig 3b).
– With a rocking motion, alternately lift
the front and the back of the insert
until the insert loosens and can be
removed (Fig 3c).
Fig 3cFig 3bFig 3a
WARNING: Always use caution when handling hot water.
• 70% rubbing alcohol or disinfecting wipes
• Squirt bottle lled with a small amount of
70% rubbing alcohol
• Dishwashing soap
• Clean cloth or soft brush
• Disposable non-latex gloves
• Hot water (about a gallon)
• Heat-resistant container, like a metal pot
• Towels to absorb any water spills
WHAT YOU’LL NEED:
TIP: The drip tray and grill should be cleaned monthly.
DIY: HOW TO CLEAN
YOUR WATER DISPENSER
TM
TIP: The best time to clean your dispenser is when the existing water bottle is empty.
Your water dispenser should be thoroughly cleaned at least twice a year. If your
dispenser hasn’t been used in a while, we recommend ushing the equipment
prior to cleaning. Here are instructions for do-it-yourself cleaning:
Before you start cleaning, wash your hands thoroughly with soap and water for at least 20 seconds.
Fig 2
Fig 1

WARNING: Dispense water through the hot and cold
spigots before plugging in and turning on the hot tank
switch. Failure to follow proper installation instructions
may cause damage to water dispenser.
6. Remove the separator by pulling it straight out. Make note
of the separator positioning before removing so that it
can be re-installed correctly (Fig 4). Clean the insert and
the separator with dishwashing soap and dry thoroughly.
8. Wearing disposable non-latex gloves, wipe the inside of the reservoir with a clean cloth
or soft brush. Use caution as the water may still be hot to the touch (Fig 6).
9. Completely drain the water from the reservoir by dispensing the water through the hot
and cold spigots into a container.
10. Repeat steps 7 and 9 to completely ush the dispenser. It is not necessary to wipe the
inside of the reservoir a second time.
No-spill
dispenser
insert
Separator
Reservoir
Fig 4
Fig 5
Fig 6
Fig 7
11. Replace the separator and the no-spill dispenser insert. Replacing the no-spill insert will
require rm pressure (Fig 7).
12. Wipe down the cooler and the surrounding area to dry any water spills.
13. Wash your hands thoroughly with soap and water for at least 20 seconds. Install a full
water bottle on the dispenser. Dispense water through the hot and cold spigots. Plug it
in and turn on the hot tank heater switch located at the rear of the dispenser.
7. Carefully pour hot water into the reservoir until it is ¾ full. Let the water
sit for 5 minutes (Fig 5). Always use caution when handling hot water.
©2020 DS Services of America, Inc.
TM
THEN plug in dispenser
and turn on the hot
tank switch.
3
Dispense water from
hot and cold faucets.
2
Load water bottle FIRST.
1