DS Services of America Pure Water Dispenser 500 Series User manual

4. Remove cup holders, if applicable.
Open the cooler lid using the key
provided in the replacement kit (Fig 4).
5. Close cooler door. Place a glass or other
container below the water faucets to
catch any drips.
Fig 2
Fig 5Fig 4
Fig 3
Fig 6
Fig 1
Your water dispenser exterior should be thoroughly cleaned at least twice a year, and your
SmartFlo™ water cartridge replaced every 12 months. If you do not have a replacement cartridge
handy, you can order one here and it will be delivered directly to you. Your replacement kit will
include a SmartFlo™ cartridge, bottle adaptor, lid key and plug for the bottle tube:
Before you start cleaning, wash your hands thoroughly with soap and water for at least 20 seconds.
TIP: Have a bucket nearby to
dispose of the used SmartFlo™
cartridge and bottle tube,
which will contain water.
DIY: HOW TO CLEAN
YOUR WATER DISPENSER
TIP: The best time to replace your water cartridge is when the existing water bottle is empty.
WHAT YOU’LL NEED:
• SmartFlo™ replacement cartridge
• 70% rubbing alcohol or disinfecting wipes
• Clean cloth or soft brush
• Disposable non-latex gloves
• Bucket
• Heat-resistant container to t under spigots
• Towels to absorb any water spills
1. Slide the cooler door up and turn o
the hot tank heater switch (Fig 1).
Let the unit stand for one hour
before cleaning to allow the hot
tank to cool.
2. Remove the empty water bottle
(Fig 2). Wipe interior cabinet
with 70% rubbing alcohol or
disinfecting wipes.
3. Unplug the bottle tube connected
to the neck of the water bottle.
Plug the bottle tube using the red
plug provided in the SmartFlo™
replacement kit (Fig 3).
6. Remove the SmartFlo™ cartridge
and bottle tube by unlatching
the blue locking arm and rotating
the two blue knobs to the open
position (Fig 5).
7. Pull up on the SmartFlo™ water
cartridge (Fig 6). Do not squeeze
the water reservoir as water could
leak out.
WARNING: Always use caution when handling hot water.
®

©2020 DS Services of America, Inc.
Fig 8 Fig 9
Fig 7
8. Wearing gloves, feed the new bottle
tube through the hole indicated
(Fig 7).
9. Insert the new SmartFlo™ cartridge
and secure into place by pressing
down (Fig 8).
10. Rotate the blue knobs to the closed
position. Close and latch the blue
locking arm (Fig 9).
11. Close the cooler lid by pushing
down to lock into place.
12. Wearing gloves, carefully unpack
the new bottle adaptor. Pull the
adaptor tube to straighten (Fig 10)
and insert it into a new water bottle.
13. Feed the tube into the water bottle
until it reaches the bottom.
14. Remove the red protective cap from the bottle tube (Fig 11). Install it into the
bottle adaptor (Fig 12).
15. Slide water bottle into the cabinet and close the door.
16. Clean spigots, bottle receptacle and cabinet with 70% rubbing alcohol or
disinfecting wipes. Vacuum or wipe the grill on the back of the dispenser to
remove any dust.
TIP: The cooler exterior should be cleaned every 6 months.
17. Clean the drip tray and grill by emptying the tray and cleaning the tray and grill with
dishwashing soap or by placing them on the top rack of the dishwasher (Fig 13).
TIP: The drip tray and grill should be cleaned monthly.
18. Wipe down the cooler and the surrounding area to dry any water spills.
19. Wash your hands thoroughly with soap and water for at least 20 seconds. Install a full
water bottle on the dispenser.
20. Prime the dispenser to ll the reservoir by holding down the cold water spigot for 1 minute,
or until water ows continuously. Repeat with the hot water spigot until water ows
continuously. Turn on the hot tank switch.
Load water
bottle FIRST.
1
THEN
turn on the
hot tank
switch.
3
Dispense
water from
hot and cold
faucets.
2
WARNING: Dispense water through the hot and cold
spigots before turning on the hot tank switch. Failure
to follow proper installation instructions may cause
damage to water dispenser.
Bottle
Tube
Fig 12Fig 11
Fig 10
Fig 13