DSE 53 Series User manual

COMPLEX SOLUTIONS
MADE SIMPLE.
DEEP SEA ELECTRONICS PLC
DSE5310
AUTOSTART CONTROL MODULE
OPERATING MANUAL
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
2 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
Deep Sea Electronics Plc
Highfield House
Hunmanby
North Yorkshire
YO14 0PH
ENGLAND
Sales Tel: [phone]
Sales Fax: [phone]
E-mail: [email protected]
Website: www.deepseaplc.com
DSE Model 5310 Control and Instrumentation System Operators Manual
© Deep Sea Electronics Plc
All rights reserved. No part of this publication may be reproduced in any material form (including photocopying or storing in any
medium by electronic means or other) without the written permission of the copyright holder except in accordance with the
provisions of the Copyright, Designs and Patents Act 1988.
Applications for the copyright holder’s written permission to reproduce any part of this publication should be addressed to Deep
Sea Electronics Plc at the address above.
Any reference to trademarked product names used within this publication is owned by their respective companies.
Deep Sea Electronics Plc reserves the right to change the contents of this document without prior notice.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 3
TABLE OF CONTENTS
Section Page
1INTRODUCTION ..............................................................................................5
2CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.........5
3OPERATION ....................................................................................................6
3.1AUTOMATIC MODE OF OPERATION...............................................................................7
3.2MANUAL OPERATION.......................................................................................................9
4PROTECTIONS..............................................................................................10
4.1WARNINGS .......................................................................................................................11
4.2ANALOGUE PRE-ALARMS .............................................................................................13
4.3HIGH CURRENT WARNING ALARM...............................................................................14
4.4SHUTDOWNS....................................................................................................................15
4.5HIGH CURRENT SHUTDOWN ALARM...........................................................................19
4.6ELECTRICAL TRIPS.........................................................................................................19
5DESCRIPTION OF CONTROLS ....................................................................20
5.1TYPICAL LCD DISPLAY SCREENS................................................................................22
5.1.1TYPICAL STATUS DISPLAY......................................................................................22
5.1.2TYPICAL INSTRUMENT DISPLAY............................................................................22
5.1.3TYPICAL ALARM DISPLAY .......................................................................................22
5.1.4TYPICAL EVENT DISPLAY........................................................................................23
5.2VIEWING THE INSTRUMENTS ........................................................................................23
5.2.1INSTRUMENT PAGE CONTENT...............................................................................24
5.2.2MANUALLY SELECTING AN INSTRUMENT............................................................24
5.2.3MODEM STATUS.......................................................................................................25
5.2.4CAN ERROR MESSAGES.........................................................................................26
5.3VIEWING THE EVENT LOG..............................................................................................26
5.4USER CONFIGURABLE INDICATORS ...........................................................................27
5.5CONTROLS.......................................................................................................................27
6FRONT PANEL CONFIGURATION...............................................................28
6.1.1ENTERING THE CONFIGURATION EDITOR PIN NUMBER...................................28
6.2EDITING A VALUE............................................................................................................30
6.2.1LIST OF ADJUSTABLE PARAMETERS IN ‘MAIN CONFIGURATION EDITOR’......31
6.2.2LIST OF ADJUSTABLE PARAMETERS IN ‘APPLICATION EDITOR’ ......................32
6.2.3EDITING THE CURRENT DATE AND TIME .............................................................33
7INSTALLATION INSTRUCTIONS..................................................................35
7.1PANEL CUT-OUT..............................................................................................................35
7.2COOLING...........................................................................................................................35
7.3UNIT DIMENSIONS...........................................................................................................35
7.4FRONT PANEL LAYOUT..................................................................................................36
7.5REAR PANEL LAYOUT....................................................................................................36
8ELECTRICAL CONNECTIONS......................................................................37
8.1CONNECTION DETAILS...................................................................................................37
8.1.1PLUG “A” 8 WAY........................................................................................................37
8.1.2PLUG “B” 11 WAY......................................................................................................38
8.1.3PLUG “C” 3 WAY........................................................................................................38
8.1.4PLUG “D” 4 WAY (OPTIONAL)..................................................................................39
8.1.5PLUG “F” 4 WAY ........................................................................................................39
8.1.6PLUG “G” 5 WAY........................................................................................................39
8.1.7PLUG “H” 4 WAY........................................................................................................40
8.1.8PC CONFIGURATION INTERFACE CONNECTOR..................................................40
8.1.9EXPANSION OUTPUT CONNECTOR.......................................................................40
8.2CONNECTOR FUNCTION DETAILS................................................................................41
8.2.1PLUG “A” 8 WAY........................................................................................................41
8.2.2PLUG “B” 11 WAY......................................................................................................41
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
4 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
8.2.3PLUG “C” 3 WAY........................................................................................................42
8.2.4PLUG “D” 4 WAY (OPTIONAL) ..................................................................................42
8.2.5PLUG “F” 4 WAY.........................................................................................................42
8.2.6PLUG “G” 5 WAY........................................................................................................43
8.2.7PLUG “H” 4 WAY........................................................................................................43
8.2.8PURCHASING ADDITIONAL CONNECTOR PLUGS FROM DSE............................43
9SPECIFICATION.............................................................................................44
10COMMISSIONING .......................................................................................46
10.1.1PRE-COMMISSIONING..............................................................................................46
11FAULT FINDING..........................................................................................47
12FACTORY DEFAULT CONFIGURATION...................................................48
13TYPICAL WIRING DIAGRAM......................................................................52
14APPENDIX...................................................................................................53
14.1ALTERNATIVE WIRING TOPOLOGIES.......................................................................53
14.1.13 PHASE, 3 WIRE.......................................................................................................53
14.1.21 PHASE, 2 WIRE.......................................................................................................54
14.1.32 PHASE, 3 WIRE ( 2 PHASE CENTRE TAP NEUTRAL).........................................54
14.2ICONS AND LCD IDENTIFICATION .............................................................................55
14.2.1PUSH BUTTONS........................................................................................................55
14.2.2STATUS / MEASUREMENT UNITS...........................................................................55
14.2.3LED INDICATION .......................................................................................................55
14.35310 IDMT TRIPPING CURVES (TYPICAL).................................................................56
14.4SENDER WIRING RECOMMENDATIONS....................................................................57
14.4.1EARTH RETURN SENDERS .....................................................................................57
14.4.2INSULATED RETURN SENDERS .............................................................................57
14.4.3FUEL LEVEL SENDERS ............................................................................................57
14.5CAN INTERFACE .........................................................................................................59
14.6OUTPUT EXPANSION...................................................................................................59
14.6.1RELAY OUTPUT EXPANSION (157).........................................................................59
14.6.2LED OUTPUT EXPANSION (548)..............................................................................59
14.7INPUT EXPANSION.......................................................................................................59
14.8COMMUNICATIONS OPTION CONNECTIONS ...........................................................60
14.8.1DESCRIPTION............................................................................................................60
14.8.2PC TO CONTROLLER (DIRECT) CONNECTION.....................................................60
14.8.3MODEM TO CONTROLLER CONNECTION.............................................................60
14.8.4RS485 LINK TO CONTROLLER ................................................................................61
14.8.5MODBUS™.................................................................................................................62
14.9ENCLOSURE CLASSIFICATIONS ...............................................................................63
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 5
1 INTRODUCTION
The DSE 5310 autostart module has been designed to allow the user to start and stop the generator, and if
required, transfer the load to the generator either manually (via external push-buttons) or automatically. The user
also has facility to view all the system operating parameters via the LCD display.
The DSE 5310 module monitors the engine, indicating the operational status and fault conditions; automatically
shutting down the engine and giving a true first up fault condition of an engine failure by a COMMON AUDIBLE
ALARM. The exact failure mode is indicated by text messages on the LCD display on the front panel.
The powerful microprocessor contained within the module allows for a range of complex features to be
incorporated as standard:
•Text based LCD display (supporting multiple languages).
•Voltage, Current and Power monitoring.
•Engine parameter monitoring.
•Fully configurable inputs for use as alarms or a range of different functions.
•Extensive range of output functions using built in relay outputs or relay expansion modules available.
Selective operational sequences, timers and alarm trips can be altered by the customer via a PC using the 52/53xx
series configuration software and P810 interface. Additionally, a subset of this information can be adjusted from the
module’s front panel configuration editor.
The module is housed in a robust plastic case for front panel mounting. Connections to the module are via locking
plug and sockets.
2 CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.
NOTE:
Highlights an essential element of a procedure to ensure
correctness.
CAUTION!
Indicates a procedure or practice which, if not strictly observed,
could result in damage or destruction of equipment.
WARNING!
Indicates a procedure or practice, which could result in injury to
personnel or loss of life if not followed correctly.
Compliant with BS EN 60950 Low Voltage Directive
Compliant with BS EN 50081-2 EMC Directive
Compliant with BS EN 50082-2 EMC Directive
Indicates a function only applicable when the controller is
configured for connection to a CAN engine controller
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
6 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
3 OPERATION
The following description details the sequences followed by a module containing the standard ‘factory
configuration’. Always refer to your configuration source for the exact sequences and timers observed by any
particular module in the field.
FIG 1
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 7
3.1 AUTOMATIC MODE OF OPERATION
NOTE:- If a digital input configured to panel lock is active, changing module modes will not be
possible. Viewing the instruments and iis NOT affected by panel lock. If panel lock is active the
Panel lock indicator (if configured) illuminates.
This mode is activated by pressing the pushbutton. An LED indicator beside the button confirms this
action.
If the Remote Start input (if configured) is activated the relevant indicator (if configured) illuminates.
To allow for false remote start signals, the Start Delay timer is initiated. After this delay, if the pre-heat output option
is selected then the pre-heat timer is initiated, and the corresponding auxiliary output (if configured) will energise.
NOTE:- If the Remote Start signal is removed during the Start Delay timer, the unit will return to a
stand-by state.
After the above delays the Fuel Solenoid (or enable ECU output if configured) is energised, then one second
later, the Starter Motor is engaged.
NOTE:- If the unit has been configured for CAN, compatible ECU’s will receive the start command
via CAN.
The engine is cranked for a pre-set time. If the engine fails to fire during this cranking attempt then the starter
motor is disengaged for the pre-set rest period. Should this sequence continue beyond the set number of attempts,
the start sequence will be terminated and Fail to Start fault will be displayed.
Alarm
Shutdown
Failed to start
When the engine fires, the starter motor is disengaged and locked out at a pre-set frequency from the Alternator
output. Alternatively, a Magnetic Pickup mounted on the flywheel housing can be used for speed detection (This is
selected by PC using the 5xxx series configuration software). Rising oil pressure can also be used to disconnect
the starter motor; however, it cannot be used for underspeed or overspeed detection.
NOTE:- If the unit has been configured for CAN, speed sensing is via CAN.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
8 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
After the starter motor has disengaged, the Safety On timer is activated, allowing Oil Pressure, High Engine
Temperature, Under-speed, Charge Fail and any delayed Auxiliary fault inputs to stabilise without triggering the
fault.
Once the engine is running, the Warm Up timer, if selected, is initiated, allowing the engine to stabilise before
accepting the load.
If an auxiliary output has been selected to give a load transfer signal, this then activates.
NOTE:-A load transfer will not be initiated until the Oil Pressure has risen. Thus preventing
excessive wear on the engine.
On removal of the Remote Start signal, the Stop delay timer is initiated, once it has timed out, the load Transfer
signal is de-energised, removing the load. The Cooling timer is then initiated, allowing the engine a cooling down
period off load before shutting down. Once the Cooling timer expires the Fuel Solenoid is de-energised, bringing
the generator to a stop.
Should the Remote Start signal be re-activated during the cooling down period, the set will return on load.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 9
3.2 MANUAL OPERATION
NOTE:- If a digital input configured to panel lock is active, changing module modes will not be
possible. Viewing the instruments and event logs iis NOT affected by panel lock. If panel lock is
active the Panel lock indicator (if configured) illuminates.
To initiate a start sequence in MANUAL, press the pushbutton. When the controller is in the manual mode
(indicated by an LED indicator beside the button), pressing the START (I) button will initiate the start sequence.
NOTE:- There is no Start Delay in this mode of operation.
If the pre-heat output option is selected this timer is then initiated, and the auxiliary output selected is energised.
After the above delay, the Fuel Solenoid (or ECU output if configured) is energised, then one second later, the
Starter Motor is engaged.
NOTE:- If the unit has been configured for CAN, compatible ECU’s will receive the start command
via CAN.
The engine is cranked for a pre-set time period. If the engine fails to fire during this cranking attempt then the
starter motor is disengaged for the pre-set rest period. Should this sequence continue beyond the set number of
attempts, the start sequence will be terminated and Fail to Start will be displayed.
When the engine fires, the starter motor is disengaged and locked out at a pre-set frequency from the Alternator
output. Alternatively, a Magnetic Pickup mounted on the flywheel housing can be used for speed detection (This is
selected by PC using the 52/53xx series configuration software). Rising oil pressure can also be used to
disconnect the starter motor; however, it cannot be used for underspeed or overspeed detection.
NOTE:- If the unit has been configured for CAN, speed sensing is via CAN.
After the starter motor has disengaged, the Safety On timer is activated, allowing Oil Pressure, High Engine
Temperature, Under-speed, Charge Fail and any delayed Auxiliary fault inputs to stabilise without triggering the
fault.
Once the engine is running, the Warm Up timer, if selected, is initiated, allowing the engine to stabilise before it
can be loaded.
The generator will run off load, unless the Remote Start on load signal is applied or, if Close generator has been
selected as a control source, the appropriate auxiliary output will then activate.
The generator will continue to run On load, until the Auto mode is selected.
If Auto mode is selected, and the remote start on load signal is not active, then the Stop Delay Timer begins,
after which, the load is disconnected. The generator will then run off load allowing the engine a cooling down
period.
Selecting STOP (O) de-energises the FUEL SOLENOID, bringing the generator to a stop.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
10 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
4 PROTECTIONS
When an alarm is present, the Audible Alarm will sound and the Common alarm LED if configured will illuminate.
The audible alarm can be silenced by pressing the ‘Mute’ button
The LCD display will jump from the ‘Information page’ to display the Alarm Page
Alarm
Warning
Low oil pressure The type of alarm. E.g. Shutdown or warning
The nature of alarm, eg Low oil pressure.
The LCD will display multiple alarms E.g. “High Engine Temperature shutdown”, “Emergency Stop” and “Low
Coolant Warning” alarms have been triggered. These will automatically scroll round in the order that they occurred;
Running in auto If no alarms are present the
LCD will display this default
page.
Generator on load
L-N 230V240A50Hz
L-L 400V133kW
In the event of a warning alarm, the LCD will display the appropriate text. If a shutdown then occurs, the module
will again display the appropriate text.
Example:-
Alarm
Shutdown
High engine temperature
Followed by….
Alarm
Shutdown
Emergency stop
Followed by….
Alarm
Warning
Low coolant level
The unit will scroll through all
active alarms in a continuous
loop.
Alarm
Shutdown
High engine temperature
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 11
4.1 WARNINGS
Warnings are non-critical alarm conditions and do not affect the operation of the generator system, they serve to
draw the operators attention to an undesirable condition.
In the event of an alarm the LCD will jump to the alarms page, and scroll through all active warnings and
shutdowns.
BATTERY CHARGE FAILURE, will be displayed if the module does not detect a voltage from the warning light
terminal on the auxiliary charge alternator.
Alarm
Warning
Charge fail
BATTERY LOW VOLTAGE, will be displayed if the module detects that the plant DC supply has fallen below the
low volts setting level. The Battery Low Voltage alarm is delayed by the Low DC Volts Delay timer.
Alarm
Warning
Low battery volts
BATTERY HIGH VOLTAGE, will be displayed if the module detects that the plant DC supply has risen above the
high volts setting level. The Battery High Voltage alarm is delayed by the High DC Volts Delay timer.
Alarm
Warning
High battery volts
MAINTENANCE ALARM, will be displayed if the maintenance period is exceeded (engine running hours or date
interval whichever is configured).
Alarm
Warning
Maintenance alarm
FAIL TO STOP, will be displayed if the module detects the engine is still running when the ‘Fail to stop timer’
expires.
Alarm
Fail to stop
NOTE:- ‘Fail to Stop’ could indicate a faulty oil pressure sender - If engine is at rest check oil sender
wiring and configuration.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
12 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
AUXILIARY INPUTS, auxiliary inputs can be user configured and will display the message as written by the user.
Example
Alarm
Warning
Bearing temp high
LOW FUEL LEVEL will be displayed if the fuel level detected by the fuel level sender falls below the low fuel level
setting.
Alarm
Warning
Low fuel level
CAN ECU ERROR If the module is configured for CAN instruments and receives an “error” message from
the engine control unit, ‘Can ECU error” is shown on the module’s display and a warning alarm is
generated.
Example
Alarm The display will alternate
between the text display and the
manufacturers error codes
Alarm
Can ECU error
Exhaust high
temperature
Can ECU error
SPNnnnnnnn
FMInnnnnnn
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 13
4.2 ANALOGUE PRE-ALARMS
The following alarms are termed ‘pre-alarms’ as they pre warn the operator of a potentially more serious alarm
condition. For instance, if the engine temperature rises past the pre alarm level, a warning condition will occur to
notify the operator. If the temperature falls below this level, then the alarm ceases, and the set will continue to run
as normal. However if the temperature continues to rise until the coolant temperature trip point is reached, the
warning is escalated and a high coolant temperature shutdown is initiated.
LOW OIL PRESSURE, if the module detects that the engine oil pressure has fallen below the low oil pressure pre-
alarm setting level after the Safety On timer has expired, a warning will occur. Alarm Warning Low Oil Pressure will
be displayed.
Alarm
Warning
Low oil pressure
HIGH ENGINE TEMPERATURE if the module detects that the engine coolant temperature has exceeded the high
engine temperature pre-alarm setting level after the Safety On timer has expired, a warning will occur. Alarm
Warning High Coolant Temperature will be displayed.
Alarm
Warning
High temperature
LOW ENGINE TEMPERATURE if the module detects that the engine coolant temperature has fallen below the low
engine temperature pre-alarm setting level after the Safety On timer has expired, a warning will occur. Alarm
Warning Low Coolant Temp will be displayed.
Alarm
Warning
Low Coolant Temp
OVERSPEED, if the engine speed exceeds the pre-alarm trip a warning is initiated. Alarm Warning Overspeed will
be displayed. It is an immediate warning.
Alarm
Warning
Overspeed
UNDERSPEED, if the engine speed falls below the pre-set pre-alarm after the Safety On timer has expired, a
warning is initiated. Alarm Warning Underspeed will be displayed.
Alarm
Warning
Underspeed
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
14 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
GENERATOR HIGH FREQUENCY if the module detects a generator output frequency in excess of the pre-set
pre-alarm, a warning is initiated. Alarm Warning High frequency will be displayed, it is an immediate warning.
Alarm
Warning
Over frequency
GENERATOR LOW FREQUENCY if the module detects a generator output frequency below the pre-set pre-alarm
after the Safety On timer has expired, a warning is initiated. Alarm Warning Low Frequency will be displayed
Alarm
Warning
Under frequency
GENERATOR HIGH VOLTAGE if the module detects a generator output voltage in excess of the pre-set pre-
alarm, a warning is initiated. Alarm Warning High voltage will be displayed, it is an immediate warning.
Alarm
Warning
AC Overvolts
GENERATOR LOW VOLTAGE if the module detects a generator output voltage below the pre-set pre-alarm after
the Safety On timer has expired, a warning is initiated. Alarm Warning Low Voltage will be displayed.
Alarm
Warning
AC Undervolts
CAN ECU ERROR If the module is configured for CAN instruments and receives an “error” message from
the engine control unit, ‘Can ECU error” is shown on the module’s display and a warning alarm is
generated.
Example
Alarm The display will alternate
between the text display and the
manufacturers error codes
Alarm
Can ECU error
Exhaust high
temperature
Can ECU error
SPNnnnnnnn
FMInnnnnnn
4.3 HIGH CURRENT WARNING ALARM
GENERATOR HIGH CURRENT, if the module detects a generator output current in excess of the pre-set trip a
warning is initiated. Alarm Warning High Current will be displayed. If this high current condition continues for an
excess period of time, then the alarm is escalated to a shutdown condition. For further details of the high current
alarm, please see High Current Shutdown Alarm.
Alarm
Warning
High current
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 15
4.4 SHUTDOWNS
Shutdowns are latching and stop the Generator. The alarm must be cleared, and the fault removed to reset the
module.
NOTE:- The alarm condition must be rectified before a reset will take place. If the alarm condition
remains it will not be possible to reset the unit (The exception to this is the Low Oil Pressure alarm and
similar ‘delayed alarms’, as the oil pressure will be low with the engine at rest).
FAIL TO START, if the engine does not fire after the pre-set number of attempts has been made a shutdown will
be initiated. Alarm Shutdown Fail To Start will be displayed.
Alarm
Shutdown
Failed to start
EMERGENCY STOP, removal of the Positive DC Supply from the Emergency Stop input initiates the following
sequence. Firstly it will initiate a controlled shutdown of the Generator and prevent any attempt to restart the
Generator until the Emergency Stop push-button has been reset. Secondly it removes the Positive DC supply from
both the Fuel Solenoid and Starter Solenoid.
Alarm Shutdown Emergency Stop will be displayed.
Alarm
Shutdown
Emergency stop
NOTE:- The Emergency Stop Positive signal must be present otherwise the unit will shutdown.
LOW OIL PRESSURE, if the module detects that the engine oil pressure has fallen below the low oil pressure trip
setting level after the Safety On timer has expired, a shutdown will occur. Alarm Shutdown Low Oil Pressure will
be displayed.
Alarm
Shutdown
Low oil pressure
HIGH ENGINE TEMPERATURE if the module detects that the engine coolant temperature has exceeded the high
engine temperature trip setting level after the Safety On timer has expired, a shutdown will occur. Alarm Shutdown
High Engine Temperature will be displayed.
Alarm
Shutdown
High temperature
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
16 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
OVERSPEED, if the engine speed exceeds the pre-set trip a shutdown is initiated. Alarm Shutdown Overspeed will
be displayed. Overspeed is not delayed, it is an immediate shutdown.
Alarm
Shutdown
Overspeed
NOTE:-During the start-up sequence the overspeed trip logic can be configured to allow an extra
trip level margin. This is used to prevent nuisance tripping on start-up - Refer to the 53xx series
configuration software manual under heading ‘Overspeed Overshoot’ for details.
UNDERSPEED, if the engine speed falls below the pre-set trip after the Safety On timer has expired, a shutdown is
initiated. Alarm Shutdown Underspeed will be displayed.
Alarm
Shutdown
Underspeed
GENERATOR HIGH FREQUENCY if the module detects a generator output frequency in excess of the pre-set trip
a shutdown is initiated. Alarm Shutdown High Frequency will be displayed, it is an immediate shutdown.
Alarm
Shutdown
Over frequency
GENERATOR LOW FREQUENCY, if the module detects a generator output frequency below the pre-set trip after
the Safety On timer has expired, a shutdown is initiated. Alarm Shutdown Low Frequency will be displayed.
Alarm
Shutdown
Under frequency
GENERATOR HIGH VOLTAGE if the module detects a generator output voltage in excess of the pre-set trip a
shutdown is initiated. Alarm Shutdown High Volts will be displayed, it is an immediate shutdown.
Alarm
Shutdown
AC Overvolts
GENERATOR LOW VOLTAGE if the module detects a generator output voltage below the below the pre-set trip
after the Safety On timer has expired, a shutdown is initiated. Alarm Shutdown Low Volts will be displayed.
Alarm
Shutdown
AC Undervolts
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 17
OIL PRESSURE SENDER OPEN CIRCUIT, if the module detects a loss of signal from the oil pressure sender
(open circuit) a shutdown is initiated. Alarm Shutdown Sender Fault will be displayed. Sender failure is not delayed,
it is an immediate shutdown.
Alarm
Shutdown
Oil pressure
sender fault
AUXILIARY INPUTS, if an auxiliary input has been configured as a shutdown the appropriate message will be
displayed as configured by the user.
Alarm
Shutdown
Bearing temp high
MAINTENANCE ALARM, will be displayed if the maintenance period is exceeded (engine running hours or date
interval whichever is configured). The engine is shutdown (if configured to do so)
Alarm
Shutdown
Maintenance alarm
LOSS OF SPEED SIGNAL, if the speed sensing signal is lost during cranking, a shutdown is initiated. Alarm
Shutdown Loss Of Speed Signal will be displayed.
Alarm
Shutdown
Loss of speed
signal
NOTE:- This will only occur if the speed sensing signal is lost during cranking or during the safety
on timer. If the signal is lost during normal operation the Generator will shutdown with an Under-speed
alarm.
CAN DATA FAIL If the module is configured for CAN operation and does not detect data on the engine Can
datalink, a shutdown will occur and ‘Can data fail’ is shown on the module’s display.
Alarm
Shutdown
Can data fail
CAN ECU FAIL If the module is configured for CAN instruments and receives a “fail” message from the
engine control unit, the engine is shutdown and ‘Can ECU fail” is shown on the module’s display.
Example
Alarm The display will alternate
between the text display and the
manufacturers error codes
Alarm
Can ECU fail
Fuel pressure low
Can ECU fail
SPNnnnnnnn
FMInnnnnnn
NOTE:- If the CAN message is a manufacturers specific code, it may not be displayed as text.
If this is the case the display will show the generic manufacturers code, which must be cross-
referenced with the engine manufacturers literature. . Please contact the engine manufacturer for
further assistance.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
18 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
Example
Alarm
Can ECU fail
SPNnnnnn
FMInnnn
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM 19
4.5 HIGH CURRENT SHUTDOWN ALARM
GENERATOR HIGH CURRENT, if the module detects a generator output current in excess of the pre-set trip a
warning is initiated. This warning will continue for a period of time depending upon the level of overload that the
generator is subjected to, and the configuration setting for Generator High Current in the 5xxx series configuration
software.
Alarm
Shutdown
High current trip
For instance the factory default settings for Generator High Current allow for a loading of the generator to 110% for
one hour. That is to say if the generator load level exceeds the trip point by 10%, a warning alarm will occur while
the overload condition exists. If the load level does not drop to normal levels within one hour, the set is stopped,
the 5310 module displaying either shutdown alarm or electrical trip alarm depending upon module configuration.
NOTE:- Higher overload levels will result in a faster acting shutdown condition. For instance with
the factory default configuration, an overload level twice that of the trip level ( typically 200%) will result
in a Generator High Current shutdown condition after 36 seconds.
For details of the relationship between the overload and the shutdown time, please see the Appendix
section of this manual.
4.6 ELECTRICAL TRIPS
Electrical trips are latching and stop the Generator but in a controlled manner. On initiation of the electrical trip
condition the module will de-energise the ‘Close Generator’ Output to remove the load from the generator. Once
this has occurred the module will start the Cooling timer and allow the engine to cool off-load before shutting down
the engine. The alarm must be accepted and cleared, and the fault removed to reset the module.
AUXILIARY INPUTS, if an auxiliary input has been configured as an electrical trip the appropriate message will be
displayed as configured by the user.
Example
Alarm
Electrical trip
Phase rotation
GENERATOR HIGH CURRENT. If the module detects a generator output current in excess of the pre-set trip a
warning is initiated. If this high current condition continues for an excess period of time, then the alarm is escalated
to either a shutdown or electrical trip condition (depending upon module configuration). For further details of the
high current alarm, please see High Current Shutdown Alarm.
Alarm
Electrical trip
High current
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com

DSE Model 5310 Automatic Mains Failure & Instrumentation System Operators Manual
20 Part No. 057-013 5310 OPERATING MANUAL ISSUE 7.1 18/06/2007 ADM
5 DESCRIPTION OF CONTROLS
The following section details the function and meaning of the various controls on the module.
Scroll Down Next page Configurable LEDs
Stop Manual Auto Mute/Lamp
Test Start
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
[email protected]
SHOP ONLINE
www.genpowerusa.com