DSE DSE 6120 User manual

053
-
0
60
ISSUE 1 DEE P S EA EL E CT RO NI CS
DSE6120 Installation Instructions
ACCESSING THE FRONT PANEL EDITOR (FPE)
The module must be in STOP mode with the engine at rest before configuration mode can be accessed.
To enter the ‘configuration mode’ press both the INFO and STOP buttons together.
ENTERING THE CONFIGURATION EDITOR PIN NUMBER
If the module PINnumber has been set, the PIN number request is then shown. The configuration
cannot be viewed or changed until the PINnumber is correctly entered.
•The first * is flashing. Press +or – buttons to adjust it to the correct value for the first digit of
the PINnumber.
•Press when the first digit is correctly entered.
•The entered digit will turn back to a * to maintain security.
•Enter the remaining digits of the pin number using the same method.
If the Configuration PINhas been entered successfully(or the PIN number has not been set in the module) the first
configurable parameter is displayed.
NOTE:- When 

is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is not
correct, the editor is automatically exited. To retry you must re-enter the editor as described above .
EDITING A PARAMETER
Enter the editor as described above.
•Press to select the required ‘page’ as detailed below.
•Press (+) to select the next parameter or (-) to select the previous parameter within the current page.
•When viewing the parameter to be changed, press the () button.The value begins to flash.
•Press (+) or (-) to adjust the value to the required setting.
•Press () the save the current value, the value ceases flashing.
•Press and hold the () button to exit the editor.
.
NOTE: - Values representing pressure will be displayed in Bar. Values representing temperature are displayed in
degrees Celsius .
NOTE: - When the editor is visible, it is exited after 5 minutes of inactivity to ensure security.
NOTE:- To exit the front panel configuration editor at any time, press and hold the () button. Ensure you
have saved any changes you have made by pressing the 

button first.
NOTE:- The PIN number is automatically reset when the editor isexited (manually or automatically) to ensure
security.
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
LO CALL (from UK BT landlines)
Telephone [phone]
Email: [e-mail]
Web: www.deepseaplc.com
Deep Sea Electronics inc.
Phone: [phone]
Fax: [phone]
TOLL FREE (USA only) :
Tel: [phone]
Email: [e-mail]
Web: www.deepseausa.com
Deep Sea Electronics Plc.
(Far East)
Tel:[phone]
Fax: [phone]
Email: [e-mail]
Web: www.deepseaplc.com
T
ypical Wiring Diagram

ADJUSTABLE PARAMETERS (Configuration editor)
(Factory default settings are shown in bold italicised text)
Section
Parameter as shown on display
Values
PIN
Pin Entry # # # #
DISPLAY
Contrast 0% - 100% (53%)
Language English - Others
LCD Page Timer hh:mm:ss (5m)
Auto Scroll Delay 1s - 1hr (2s)
ALT CONFIG
Default Config Default Config
ENGINE
Oil Pressure Low Shutdown 0bar - 9.97bar (1.03bar)
Coolant Temperature High Shutdown 2ºC - 140ºC (95ºC)
Start Delay Timer 0 - 10hr (5s)
Pre Heat Timer 0 - 5m (0s)
Crank Duration Timer 0 - 1m (10s)
Crank est Timer 0 - 1m (10s)
Safety On Delay 0 - 1m (10s)
Smoke Limiting 0 - 15m (0s)
Smoke Limiting Off 0 - 1m (0s)
Warm Up Timer 0 -1hr (0s)
Cool Down Timer 0 - 1hr (1m)
Speed Low Shutdown Active, Inactive
Speed Low Shutdown 0RPM - 6000RPM (1270RPM)
Speed High Shutdown 0RPM - 6000RPM (1740RPM)
Speed Overshoot Delay 0-10s (2s)
Speed Overshoot 0% - 10% (0s)
Fail To Stop Delay 0 - 2m (30s)
Battery Voltage Low Warning Active, Inactive
Battery Low Voltage 0V – 40V (10V)
Battery voltage Low Warning Delay 0 - 24hr (1m)
Battery Voltage High Warning Active, Inactive
Battery Voltage High Warning Delay 0V - 24hr (1m)
Battery Voltage High Warning 0V – 40V (30V)
Charge Alternator Failure Warning Active, Inactive
Charge Alternator Failure Warning 0V – 39V (6V)
Charge Alternator Failure Warning Delay 0 - 24hr (5s)
Charge Alternator Failure Shutdown Active, Inactive
Charge Alternator Failure Shutdown 0V – 5.9V (4.0V)
Charge Alternator Failure Shutdown Delay 0 - 24hr (5s)
GENERATOR
Voltage Low Shutdown 50V – 360V (184V)
Voltage Nominal 50V – 276V (230V)
Voltage High Shutdown 231V – 360V (277V)
Frequency Low Shutdown 0Hz - 75Hz (43Hz)
Frequency Nominal 0Hz - 75Hz (50Hz)
Frequency High Shutdown 0Hz - 75Hz (58Hz)
Full Load ating 5A – 6000A (500A)
Delayed Over Current Active, Inactive
Delayed Over Current 50% - 120% (100%)
AC System Single Phase, 2 Wire
3 Phase, 4 Wire
3 Phase, 4 Wire3 Phase, 4 Wire
3 Phase, 4 Wire
2 Phase, 3 Wire (L1 & L3)
3 Phase, 4 Wire (Delta)
2 Phase, 3 Wire (L1 & L2)
3 Phase, 3 Wire
CT Primary 5A - 6000A (600A)
Generator Transient Delay 0 - 10m (0.7s)
ront Panel Configuration Editor
(Factory default settings are shown in bold italicised text)
Section
Parameter as shown on display Values
MAINS Voltage Low Trip 50V – 360V (184V)
Voltage High Trip 50V – 360V (276V)
Frequency Low Trip 0Hz - 75Hz (45Hz)
Frequency High Trip 0Hz - 75Hz (55Hz)
Mains Transient Delay 0 - 30s (2s)
eturn Delay 0 - 1hr (30s)
Mains Transfer Time 0 - 10m (0.7s)
TIMERS LCD Page Timer hh:mm:ss (5m)
Auto Scroll Delay 1s - 1hr (2s)
Pre Heat Timer 0 - 5m (0s)
Crank Duration Timer 0 - 1m (10s)
Crank est Timer 0 - 1m (10s)
Safety On Delay 0 - 1m (10s)
Smoke Limiting 0 - 15m (0s)
Smoke Limiting Off 0 - 1m (0s)
Warm Up Timer 0 -1hr (0s)
Cool Down Timer 0 - 1hr (1m)
Fail To Stop Delay 0 - 2m (30s)
Battery voltage Low Warning Delay 0 - 24hr (1m)
Battery Voltage High Warning Delay 0V - 24hr (1m)
Return Delay 0 - 5hr (30s)
Generator Transient Delay 0.1s - 2m (30s)
Mains Transient Delay 0 - 30s (2s)
Mains Transfer Time 0 - 10m (0.7s)
DIMENSIONS AND MOUNTING
DIMENSIONS
216mm x 158mm x 42mm
(8.5” x 6.2” x 1.6”)
PANEL CUTOUT
182mm x 137mm
(7.2” x 5.4”)
1.1.1 WEIGHT
510g (0.51kg)
1.1.2 FIXING CLIPS
The module is held into the panel fascia using the supplied fixing clips.
•Withdrawthe fixing clip screw(turn anticlockwise) until only the pointed end is protruding from the clip.
•Insert the three ‘prongs’ of the fixing clip into the slots in the side of the 6000 series module case.
•Pull the fixing clip backwards (towards the back of the module) ensuring all three prongs of the clip are
inside their allotted slots.
•Turn the fixing clip screws clockwise until they make contact with the panel fascia.
•Turn the screws a little more to secure the module into the panel fascia. Care should be taken not to over
tighten the fixing clip screws.
NOTE:- In conditions of excessive vibration, mount the panel on suitable
anti-vibration mountings.