DSE DK-V2-4G User manual

Document:DK-V2-4G 2B3
Page: 1
DK-V2-4G Dash Cam Car CameraUSER MANUAL
DK-V2-4G Connected in this way, the camera records continuously only when
the vehicle is on. With the vehicle off, the parking function can be
enabled which records if the vehicle is hit.
If you want to record continuously, even when parked, you can
connect both the BAT and ACC connectors to a fuse holder which
gives voltage that is always present even when the ignition is off. In
this case, however, it is advisable to also install a battery-saving
device, which disconnects the camera if the battery is running low,
and an external switch on the ACC cable, to be able to turn off the
camera in the event of long stops.
Camera and
car black box with 4G
video recorder
Product composition
1. Dash cam camera
2. Internal secondary cameras
3.GPS antenna
4. Connection cable to vehicle control unit
5. Double-sided adhesive bracket
Product description Mounting the dashcam
DK-V2-4G is a car video recorder equipped with an integrated front
camera and a second camera for filming the interior of the vehicle.
It is ideal to be mounted on the windshield with the included
adhesive bracket and monitor everything that happens around the
vehicle. It is equipped with a 4G SIM slot that allows web control.
The camera should be positioned near the rear view mirror, in
order to have a good front view. The best position is towards the
passenger side, as shown, so as not to obstruct the driver's view.
The bracket is equipped with a high-strength adhesive. It is
advisable to clean the glass well and check the framing before
gluing the bracket.
The lens can be rotated to adapt to the inclination of the windshield
and perfectly frame the road in front of the vehicle.
The indoor camera and GPS antenna connect to the power cable at
their connectors. The camera is always positioned on the
windscreen, facing the inside of the passenger compartment, the
antenna is equipped with a magnet to be hooked to the bodywork
at any point in the passenger compartment, even hidden
Dash cam wiring
The dashcam is supplied with a cable that allows you to connect it
to the vehicle's control unit and to which you also connect the
internal camera and the GPS antenna.
The power cord has these 3 connectors
.
BAT – Yellow BAT+ cable connects to a fuse holder which always
supplies current, even when the vehicle is off.
ACC – Red ACC wire connects to a fuse holder that supplies power
only when the vehicle is running.
GND – Ground lead connects to a vehicle chassis ground screw
You can connect the connector to an empty fuse holder, or buy a
separate splitter that allows you to connect both the camera and
the original fuse in one place Turning on the camera and recording
The camera turns on automatically when it receives 12VDC power
simultaneously on the BAT and ACC terminals. When the vehicle is
switched off, the voltage on ACC fails and the camera goes into
Parking mode.
Parking Mode
In Parking mode the camera remains dormant with negligible
consumption. Recording starts if the vehicle is hit to document
what happened. The camera is also activated if a remote web
connection is requested via the app.
Indication LEDs
The camera is equipped with 3 indication LEDs: RED LED –
Flashing if recording abnormal BLUE LED – Flashing when 4G
network not connected GREEN LED – Flashing when GPS out of
range
DSE srl - Digital Surveillance Equipment – www.dse.eu

Document:DK-V2-4G 2B3
Page: 2
DK-V2-4G Dash Cam Car CameraUSER MANUAL
GREEN LED – Steady when all functions are normal
Insert the micro SD card
The first thing to do, if you want to make recordings, is to insert the
micro SD card in the appropriate slot on the DVR (TF)
It is possible to use micro SD cards with capacity up toto 128GB in
CLASS 10or higher. The SD card is not included in the package.
As an indication, consider that one minute of continuous recording
at 1080P occupies about 90MB, therefore a 128GB SD card can
contain about 24 hours of continuous recording.
Once the SD card has been inserted into the slot, the red led
signaling anomalous recording switches off and an audible
confirmation of inserted SD card is emitted. CAMERA BUTTON - The camera has a camera button that you can
press at any important moment to highlight and protect from
overwriting the recorded footage of that moment. Movies
protected with this button are stored in a separate folder for easy
identification.
Pressing this button TWICE will enable/disable the camera alert
voice. LONG press this button to enable/disable wifi.
Insert the 4G SIM
If you want to be able to control the dashcam through the WEB, you
need to insert a 4G sim card into the SIM slot. The camera supports
the MicroSIM format. If you have a smaller format SIM, NanoSIM,
you will need an adapter (not included). Insert the card until you
hear the locking click. Once the SIM card has been inserted, if there
is a 4G data network from your provider, the flashing blue LED,
which signaled the disconnected network, turns off and the
message: Network OK is played.
ON/OFF BUTTON – By pressing this button, the camera vocally
indicates the status of Wifi, GPS, 4G SD card. Pressing this button
for 3 SECONDS restores the factory settings. This button is also
used to confirm pairing to the cloud app.
Protection of recorded files
Normally the camera records until the memory runs out, then
overwrites the recorded files starting from the oldest. It is possible
to protect the file being recorded from being overwritten by
pressing the key with the camera icon on the camera. The camera
also automatically protects the recorded files from overwriting
following the intervention of the collision sensor.
Using the free Cloud DVR app
The camera is controlled with the free appCLOUDDVR extension
which can be used to check the framing of the camera and to
manage the recordings, both in local wifi connection and via the
web.
Search and download the CLOUDDVR app for Android or iOS from
Google Play or Apple Store.
Registration
The camera starts recording automatically on start-up and saves
video files in 1920x1080 30 f/s resolution, complete with audio, on
the SD card. The files saved on the SD card are H264 videos in .TS
format with a duration of 2 minutes each.
When the vehicle is stationary, in parking mode, the camera only
records if the vehicle is hit.
Once the app is installed, the first thing you need to create an
account to access.
Once you have created your account, you need to link the camera
to your account.
By default, the camera creates its own Wifi network to which you
can connect with your phone. Open the phone's wifi network
management and connect to the camera's wifi network which you
will find among the available networks with an abbreviation FX_--
The factory password of the wifi network of the camera is:
12345678
Buttons
The camera has two buttons: Power and Camera.
DSE srl - Digital Surveillance Equipment – www.dse.eu

Document:DK-V2-4G 2B3
Page: 3
DK-V2-4G Dash Cam Car CameraUSER MANUAL
If you have not inserted the SIM card into the camera, the phone
may notify you that the wifi network does not have access to the
Internet: choose to keep the connection.
Launch the CLOUDDVR app now
If you are connected to the camera's wifi, the app will automatically
detect the camera and present you with a message requesting your
consent to pair the camera with the app. The path is different
depending on whether or not you have inserted the SIM, as
explained below.
LOCAL PAIRING – If you have not inserted the SIM, pressing the
pairing confirmation message the camera will pair with the app
only temporarily for local control. In this situation you can only
manage the camera when you connect to its wifi network. WEB
PAIRING – If you have inserted the SIM press the pairing
confirmation message and you will hear a message asking you to
press the ON/OFF button on the camera within 5 seconds. Press the
ON/OFF button within 5 seconds and the camera will be paired with
your app in the cloud server. Once the camera has been paired in
this way, you will be able to reach it via the Internet even by
disconnecting from the camera's wifi network.
A camera can be connected to several users of the app, but only
one active connection is possible at a time. The app allows you to control the front and rear camera. With the
small An/P button at the top left you can select the camera. With
the camera and video camera buttons below the image, you can
take photos and record videos to save on your phone.
Only when accessing in 4G mode is the HOLD button available in
the center of the screen. Press and hold this button for two-way
dialogue using the speaker and microphone in the camera.
DSE srl - Digital Surveillance Equipment – www.dse.eu

Document:DK-V2-4G 2B3
Page: 4
DK-V2-4G Dash Cam Car CameraUSER MANUAL
ALARM ON COLLISION – Enables the surveillance function while
parking. When the vehicle is off, the camera goes into Stand-By
(Sleep) mode and activates automatically if the vehicle is hit. LOCK
COLLISION IMAGES – If you enable this function the camera will
protect the video before and after a collision from overwriting to
save the images of the accident.
SILENCE – Disable audio in recording GPS WATERMARK – If enabled,
it overlays the GPS coordinates on the video.
REAR MIRROR – Mirrors the rear camera image.
RESTART RECORDING – Restart the DVR and apply any changes in
the video recording
FORMAT SD CARD – Format the SD card deleting its contents.
FACTORY RESET – Restore the factory settings.
Reproduction
Recordings are accessed with the File Recorder button or with the
ALBUM icon.
The recordings section is divided into 4 folders where they are
saved respectively from left to right
- IMPORTANT FILES PROTECTED BY PRESSING THE CAMERA
BUTTON ON THE CAMERA
- IMPORTANT FILES PROTECTED FROM OVERWRITE BY
COLLISION SENSOR
- CONTINUOUS RECORDING FILES
- FILES DOWNLOADED ON THE PHONE
To download the videos from the camera and save them in your
phone press and hold the file icon for a few seconds.
At the bottom of the screen you see the GPS map or you can switch
to a second page that allows you to view the recorded files and set
some camera options
User
The user section is accessed with the IO button. It is possible to
review the route stored by the GPS.
Use of the CMSV6 fleet management app and software
The camera you have purchased includes a one-year subscription to
the CMSV6 fleet management platform. IP address, user name and
password to access the platform are sent to you via email.
CMSV6 is a very powerful web-based fleet management platform
with many advanced features that you can use instead of the free
CloudDVR app. It is very useful especially for the management of
fleets of vehicles when many dashcams have to be monitored at the
same time.
You can download the CMSV6 software from our website and the
CMSV6 app or also CMSV7 (new version) from the iOS and Android
stores.
You can also use CMSV6 with our dashcams simply with a browser
by connecting to the IP address http://47.241.210.146/
For the use of CMSV6 refer to the specific manual.
In order not to burden the server, the real-time video connection
via web has a timing that automatically closes it in the absence of
operator commands.
Options configuration
These are the operating options that you can configure in the menu
CHANGE PASSWORD - You can change the name and password of
the camera's wifi network
COLLISION SENSITIVITY - You can adjust the sensitivity of the
internal collision detector (G-Sensor) which is used by the camera to
freeze images in the event of an accident or to detect an impact in
parking surveillance.
DSE srl - Digital Surveillance Equipment – www.dse.eu