DSE DK-RT1-CSC User manual

Document: DK-RT1-CSC 2F1
Page: 1
USER'S MANUAL DK-RT1-CSC Camera with hidden video recorder
DSE srl - Digital Surveillance Equipment - www.dse.eu
DK-RT1-CSC
Camera with WiFi DVR
Product description
DK-RT1-CSC is a video recorder with an integrated
camera hidden in a fake WiFi router.
1. Target
2. Invisible infrared illuminator
3. Brightness sensor
4. PIR motion detector
5. Antenna
6. USB port for power supply
7. Fake LAN port
8. Speaker
9. Side opening for battery compartment
10. Microphone
11. Removable sliding base
Access the battery compartment
To access the internal battery compartment, slide the
router base back until it is removed. Then remove the left
side of the router.
11. Base to remove
12. 2 Batteries as standard. You can possibly add 2 more
batteries to be purchased separately.
13. Camera power button
14. Reset button
Pressed 4 sec. First double beep = WiFi configuration
Pressed 6 sec. Second double beep = Factory reset
15. Micro SD card slot
16. Charging indicator (solid red while charging | off when
charging is complete.
17. WiFi status indicator
Flashing blue = WiFi configuration mode,
Solid blue = Waiting for wifi configuration
Off = Wifi connected)
Audio
This camera is equipped with a microphone for ambient
listening and a built-in speaker thanks to which you can
communicate with people close to the camera by pressing
the app buttons.
Infrared illuminator
This camera is equipped with an invisible infrared
illuminator for night vision in absolute darkness. The
illuminator turns on by itself if the ambient light does not
allow for color shooting. Through the control app you can
possibly force the day mode (always shooting in color) or
night (always shooting B / W).
Battery powered with PIR
The camera is able to operate with only the power supply
of its own internal batteries. It is equipped with a PIR
presence detector which allows it a very long autonomy.
Factory supplied with 2 2600 mAh 18650 batteries each
that allow up to 1 year of autonomy in Stand-by, in the
absence of motion detections. If you want, you can buy
two additional batteries separately to be inserted in the
free slots to double the autonomy.
Charging the battery
Before using the device, it is advisable to fully charge the
battery. To do this, connect the USB port of the camera to
8VERWPEXIHJVSQ -XEPMERXS)RKPMWL[[[SRPMRIHSGXVERWPEXSVGSQ 

Document: DK-RT1-CSC 2F1
Page: 2
USER'S MANUAL DK-RT1-CSC Camera with hidden video recorder
DSE srl - Digital Surveillance Equipment - www.dse.eu
the computer or to a USB socket charger (not included)
using the cable supplied.
The complete recharge of the 2 standard batteries takes
about 12 hours depending on the initial state of charge.
The charge LED lights up red during charging and turns off
when charging is complete.
Understanding how cameras work with
PIR
The DK --- CSC cameras are cameras with PIR presence
detectors, designed to allow a long battery life.
A camera of this type normally works in stand-by,
consuming very little battery while allowing remote access
via the app. When a person or animal is detected, the
camera activates, takes a photo and records a video with
a programmable duration. It also sends the photo with a
push notification to the CamSC app.
At the end of the event, the camera returns to rest to
activate a new detection if the presence of people
remains.
Power supply
Although these cameras are mainly purchased for long
battery life, they can also operate on mains by connecting
the USB plug to a USB cellphone power supply (not
included). If you have a way to connect the appliance to
the mains you will not have to worry about autonomy and
the camera will always be in operation. You can leave the
batteries as a backup, or remove them.
Movie storage
The video files are stored on a micro SD card (not
supplied). The movies have Full HD 1920x1080 resolution
at 25 f / sec. and are saved in MP4 format with H264
compression
It is possible to use micro SD cards of any brand up to 64
GB of capacity.
1 minute of recording occupies an average of 24MB so on
a 64 GB SD card you can store over 40 hours of recording.
Once the memory has run out, the DVR will automatically
overwrite the oldest files.
These long-range cameras do not allow continuous
recording, but only short clips in case of motion detection.
To review the recorded videos you need to download them
from the app as the files are not visible by inserting the
memory into a computer.
Inserting the micro SD card
The first thing to do, if you want to make recordings, is to
insert the micro SD card into the appropriate slot in the
DVR (15).
It is possible to use micro SD cards with capacities up to
64 GB in CLASS 10 or higher.
A class 10 SD card has a write speed of 10 MB / s. Do not
use SD cards with lower speeds as they will lead to
malfunctions.
Pay attention to the direction of insertion of the SD card
which will slide into its seat only with the gold contacts
facing the straight edge of the slot. You need to push the
microSD card in until you hear the click and the hook.
To remove the SD card, push it inwards with your
fingernail until you feel the release of the retaining clip,
then pull the card outwards.
For the memory to be used by the camera for recording, it
must be formatted as explained in the CamSC app
manual.
No micro SD card is included in the package.
Turn on the device
The camera has a power switch (13).
To install and use the product you need to use a
smartphone or tablet with the free CamSC app.
Download the CamSC app to use the camera
This camera has been developed to be remotely controlled
via wifi with a mobile phone or tablet and requires to be
connected to a wifi network, such as that generated by
your router, or from a smartphone in HotSpot mode.
It is not possible to use these cameras without a wifi
network connected to the Internet because all the
functions are managed by the key server online via the
web.
First you need to download the CamSC application from
Google Play or Apple Store, available for free for Android
and iOS. The CamSC app allows you to install and use the
device.
For the use of the CamSC APP see the specific manual
which you can download from our site.
Activate the wifi configuration mode
To use this camera you need to connect it to a wifi
network. This is easily done using the CamSC app
following the instructions contained in the app manual. To
be able to connect the camera to your wifi through the
app, you must activate the wifi configuration mode by
pressing and holding the RESET button for 4 seconds,
until you hear a double warning beep. Do not keep the
button pressed beyond the first double beep, otherwise
you will perform a factory reset as explained in the next
paragraph. When the camera enters wifi configuration
mode, the blue LED flashes slowly. If you see the blue
LED flashing in the camera you can start the configuration
operations explained in the app manual, to connect the
camera to your wifi.

Document: DK-RT1-CSC 2F1
Page: 3
USER'S MANUAL DK-RT1-CSC Camera with hidden video recorder
DSE srl - Digital Surveillance Equipment - www.dse.eu
Camera reset
In case of need, for example if you change your wifi
network, you can perform a factory RESET by pressing the
reset button for 6 seconds. The camera emits a double
beep after 4 seconds (wifi configuration mode) and a
second double beep after 6 seconds (reset). After
rebooting the DVR will return to factory settings.
Movie playback
To review and manage the recorded files it is necessary to
download them through the app. It is not possible to
manage video files by inserting the microSD card into a
computer.
Main technical characteristics
Sensor CMOS
Maximum resolution FullHD 1080p (1920x1080)
Frame rate 30 f / sec
Video format MP4 (H264 compression)
Overlay Date time (not excludable)
Functions Motion recording
Live view
Push intrusion notifications
WiFi control 2.4 GHz
Internet wifi connection required
Audio microphone Incorporated
Audio speaker Incorporated
IR illuminator Invisible. 6 m night vision.
Video storage About 40 hours on 64GB at
1080P
Operating
temperature -5 ° + 40 ° C
Memory MicroSD Class 10 or higher
Memory capacity 4..64 GB