DSPPA MAG6701 User manual

[email protected] /www.dsppatech.com The specifications will be subject to change without prior notice.
Copyright © Guangzhou DSPPA Audio Co.,Ltd All rights served.
MAG6701
100V Network Terminal
MAG6701 100V Network terminal is a network full digital analog-digital signal conversion processor based
on TCP/IP communication protocol. Dual-network redundancy design makes it possible to any place where
there is network. Remote digital data flow could export audio signal through this device, which is controlled
by host. There is built-in MP3 player, USB interface and SD card interface. You could also play local MP3
program when there is no Network audio signal. It could execute timing function without host. There is one
audio input interface to connect with other audio equipment (such as DVD). There is one auxiliary audio
output interface to connect with other amplifiers to extend power. There is also a MIC interface to realize
local paging.
Dual-network redundancy design, able to work cross network segment
Able to be installed to any place where there is network.
Built-in MP3 player, with USB interface and SD interface to play local program
Independent execution of timing function without host
Support maximum 48kHz sampling rate, 16 bit digital audio decoding
Built-in 1×60W high fidelity digital amplifier, low power consumption
Able to play background music, emergency paging and alarm signal from system host
One auxiliary audio input interface, one auxiliary audio output interface, two MIC input interfaces, one
EMC emergency output interface and one short circuit output
Controllable volume and playing status of local output
LED indicator to show signal status, working status and information change
Support infrared remote control
Could set priority of audio source through Network
Description
Features

[email protected] /www.dsppatech.com The specifications will be subject to change without prior notice.
Copyright © Guangzhou DSPPA Audio Co.,Ltd All rights served.
Model
MAG6701
AUX IN
Input sensitivity
300 mV±30mV
Frequency response
80Hz-16kHz(±3dB)
Distortion
≦1%
Noise
14mV
Signal-to-noise ratio
≥77dB
AUX OUT
Input sensitivity
1000mV±100mV
Frequency response
35Hz-20KHz(±3dB)
Distortion
0.1%
Noise
0.12 mV
Signal-to-noise ratio
≥77 dB
Maximum
output power
of the built-in
power amplifier
Single channel mode
60W/160Ω
Maximum harmonic distortion of the built-in
power amplifier
≦1%
MIC input
Input sensitivity
3.5 mV±1mV
Frequency response
80Hz-16kHz(±3dB)
Distortion
≦0.5%
Noise
14mV
Signal-to-noise ratio
≥77 dB
USB/SD
/NET
Play MP3
Input sensitivity
100V±5V
Frequency response
85Hz-16kHz(±3dB)
Distortion
≦0.4%
Noise
14 mV
Signal-to-noise ratio
≥77dB
Capacity of external U disk supported
32GB
Voltage range of power supply voltage
AC220V/50Hz
Overcurrent, overheat, over-voltage and
under-voltage protection
Support
Package dimension (L×W×H mm)
330×270×125
Machine dimension (L×W×H mm)
222×195×56
Net weight
2.35kg
Gross weight
3.2kg
Specifications

[email protected] /www.dsppatech.com The specifications will be subject to change without prior notice.
Copyright © Guangzhou DSPPA Audio Co.,Ltd All rights served.
STBYNet Service
Timing
Signal
100V Backup
Protect
VOL+
VOL-SetF1USB
100V Network Terminal MAG6701
1 2 3 4 5 678 9 10 11 12 13 14 15 16
1 button
USB disk playing mode: to play previous song. IP
setting mode: move left/move right to view/set parameters.
2 Play/Pause button
To control play/pause of local MP3 program playback.
When setting address, this button is used to save the
settings.
3 Network indicator (Net Service)
When this device is successfully connected to host through
Network, this indicator will be turned on.
4 Timing indicator (Timing)
This device could execute timing function without host
control. When executing, indicator will be turned on.
5 Amplifier output level indicator (Signal)
This indicator will be turned on when there is signal output
from this terminal. This indicator will be brighter when
increasing volume and it will be darker when turn down
volume.
6 USB button
U disk play/pause button. When setting IP, this button could
be used to exit setting status.
7 F1 button
Use when adjust volume. This button could be used to
switch among AUX IN, MIC IN/MIC 2, and MP3.
8 Local setup button (Set)
Long press this button to enter IP address view status. Press
again to enter IP setup/modify status.
9 VOL- button
Play mode: to turn down volume.
View IP: to select parameter to be viewed.
Set up IP: to increase or decrease parameters.
10 Amplifier protection indicator
This indicator will be turned on when there is short circuit.
11 100V input
When there is 100V input, this indicator will be turned on.
12 Standby indicator (STBY)
Standby function indicator which is also a mute function
indicator. When there is a Network alarm and emergency, it
will be turned on. Alarm and emergency signal could
suppress mute function.
13 VOL+ button
Playing mode: volume up.
IP viewing mode: to switch among parameters.
IP setting mode: to increase or decrease parameters.
14 button
U disk playing mode: to play next song.
IP setting mode: move right to view/set parameters.
15 Digital display screen and receiving window of
infrared remote
Digital display screen will display working status and
Network information. There is a built-in receiving window
of infrared remote to receive remote control.
16 Screw fixing hole
This terminal could be installed on the wall. There are
four screw fixing holes which are used to fix the device on
the wall.
Front / Rear Panel

[email protected] /www.dsppatech.com The specifications will be subject to change without prior notice.
Copyright © Guangzhou DSPPA Audio Co.,Ltd All rights served.
24V
LAN2LAN1 Micro SDUSB Disk AUX lN
AUX OUTMIC2 MIC1
COM SC 100V
IN
100V
OUT
+ +
请勿打开，以免触电
警告
~220V/50Hz
/100W
POWER
电源
广州市迪士普音响科技有限公司 Guangzhou DSPPA Audio Co.,Ltd.
100V网络定压壁挂终端
24V
IN
IN+
A
OUT+
OUT
COM
B
1 2 34 12 13 14
9 10 11
65 7
8
24V
LAN2LAN1 Micro SDUSB Disk AUX lN
AUX OUTMIC2 MIC1
COM SC 100V
IN
100V
OUT
+ +
24V
IN
IN+
A
OUT+
OUT
COM
B
1. Network interface (LAN1/LAN2)
Dual Network design, support hand-in-hand connection,
connect with Network POE.
2. USB interface (USB Disk)
Insert U disk or mobile hard disk with MP3 program inside
to provide MP3player with program.
3. SD card interface (Micro SD)
If the inserted SD card has timing points, host will play
program when terminal is offline.
4. Auxiliary input interface (AUX IN)
To connect with audio source equipment (such as DVD) to
extend program source.
5. EMC prior playing output
Output signal of this interface is controlled by host.
6. 100V external audio input
To connect with other standby amplifier.
7. Amplifier output (100V)
Built-in 1×60W digital amplifier with rated power 60W to
connect with multiple speakers. Total power of connected
speakers should be no more than 60W.
8. Extension interface
For extending or customizing other functions. It can be
extended to MAG6465/MAG6566 SOS, Dual Intercom
Extension Controller, MAG6402 Network PA System
On-Demand Terminal, MAG6405 GPS Calibration Module,
MAG6419 IP Network Terminal with Built-in Amplifier,
MAG6420 IP Control Panel with Bluetooth & MIC,
MAG6420II-C Network Control Panel with Wireless
Microphone. This terminal provides DC voltage power
supply for the connected equipment. The wiring method
needs to be connected with the equipment one by one
according to the requirements. For the connection method,
please refer to the instruction manual of the connecting
equipment.
9. MIC2 interface
To connect with MIC.
10. MIC1 sound pickup
Built-in pickup window. Speak to this window to broadcast.
11. Auxiliary output interface (AUX OUT)
To connect with other amplifiers to extend power.
12. AC220V power cable
To supply power.
13. Power switch (POWER)
Press “I” to turn on power supply. Press again to turn off.
14. Heat dissipation