Dunelm 30151830 User manual

DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set
the standard for quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves,
please don’t hesitate in contacting us on 08451 656565 where our team will be very
keen to understand what has gone wrong and, more importantly, put it right.
DEAR CUSTOMER
The next step…
There is no need to feel daunted by the number of parts and fittings in front of you, we have
compiled this straight forward, step-by-step guide to make sure that assembling your furniture
is as easy as 1, 2, 3.
Before you begin, we advise that you check that you have everything you need to get started.
TOP TIP
Find a space to spread these out across the floor before you begin
assembling them. Lay each panel down in position, ready to build.
It is recommended that two people assemble this product together.
The full list of furniture parts, fixtures and fittings, as well as the tools you will need for assembly,
can be found on page 2 and 3 of this manual.
TOP TIP
Identify all of the fittings, make sure that you have them all prepared
and familiarise yourself with each component, to make things easier
when you are putting it all together.
Safety and Care Advice
IMPORTANT - The first step you need to take is to ensure your safety!
Please take the time to read and understand these instructions before assembling your
furniture.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials way from children to avoid danger of suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Make sure that you allow enough space to move around when assembling your furniture.
All manuals and user guides at all-guides.com
all-guides.com

Panels - plan view
Left side
391 x 847mm
Right side
391 x 847mm
Top 995 x 388mm
Back
804 x 1012mm
Rail
995 x 78mm X 3
Panels - exploded view
Parts & Fittings for the Indiana 4 Drawer Chest
White (30151830), Black (30152651)
L/H drawer side
350 x 135mm X 4
R/H drawer side
350 x 135mm X 4
Drawer back
954.5 x 135mm X 4 Drawer base
347 x 966mm X 4
Drawer front
989 x 192mm X 4
1 2
3
4
10
2
5 6
78
9
5
6
7
8
9
2
4
4
4
10
1
3
All manuals and user guides at all-guides.com

Cross slot screwdriver Hammer Tape measure
Tools required
The use of power tools to assemble the product is not recommended due to the risk of
over tightening fixings
Front edge
Note: Insert metal
dowels as far as shown.
Fittings
Euro screw s x 16
Soft close runner x 4 pair
Handle x 4
Important information
The finished surface of the drawer fronts are hi-gloss, take care when cleaning, wiping and
handling these panels. There is also a protective film covering the drawer front and edges,
this should be removed before the handles are attached (step 17).
Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 08451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Ready?
Follow this step-by-step guide
3
B
B
B
1
1
B
B
B
15mm
Metal cam x 10
A
Cam pin x 18
B
30mm
Wooden dowel x 10
C
Panel pins x 30
G
E
Handle screw x 8
J
I
12mm
Metal cam x 8
D
Drawer peg x 16
F
K
Drawer wedge x 16
H
All manuals and user guides at all-guides.com

Front edge
Front edge
Note: Insert metal
dowels as far as shown.
4
2
3
1
E E
K
1
K
K
1
K
K
K
K
B
B
2
BB
B
B
All manuals and user guides at all-guides.com

Front edge
Rear edge
Ensurethe cam is pressed fully
into the hole and arrow pointing
towards the short edges
X 3 10 mm
5
4
5
2
EE
K
2
K
K
2
K
K
K
K
3
A
A
AA
AA
C
3
3
C
C
C
C
4
A
CA
C
All manuals and user guides at all-guides.com

Cam lock in closed
position
Cam lock in open
position
Front edge
Front edge
Front edge
Front edge
Cam lock in closed
position
Cam lock in open
position
6
6
7
AA
A
A
3
1
A
3
1
3
1
A
A
A
AAA
4
1
4
4
4These panels must be
supported until the
next step
All manuals and user guides at all-guides.com
all-guides.com

Front edge
Front edge
Cam lock in closed
position
Cam lock in open
position
Front edge
Front edge
7
8
9
3
2
A
A
A
4
4
4
1
A
A
AA
Back of unit
Two people required
to turn unit over
A to B = C to D
2
4
310
4
1
All manuals and user guides at all-guides.com

Two people required
to stand unit upright
Front edge
Ensurethe cam is pressed fully
into the hole and arrow pointing
towards the short edges
8
10
11
12
G
GG
G
G
10
G
10
10
D
5
D
6
D
5
6
X 4 X 4
5
6
7
F
F
X 4
All manuals and user guides at all-guides.com

Note: Insert metal
dowels as far as shown.
9
13
14
D
D
5
6
Cam lock in open
position
D
Cam lock in closed
position
D
7
8
9
D
6
8
9
D
5
8
9
BB
9
15
5
6
7
8
X 4
X 4
X 4
All manuals and user guides at all-guides.com

10
16
17
6
8
9
H
H
5
7
5
7
8
9
X 4
6
J
J
I
BEFORE ATTACHING THE
HANDLES REMOVE THE
PROTECTIVE FILM FROM
THE FRONT AND
EDGES OF THE
DRAWER FRONTS
LEFT AND RIGHT DRAWER RUNNERS
K
K
2
1
18
X 4
All manuals and user guides at all-guides.com