Dunelm Ontario 30149680 User manual

DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set
the standard for quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves,
please don’t hesitate in contacting us on 08451 656565 where our team will be very
keen to understand what has gone wrong and, more importantly, put it right.
DEAR CUSTOMER
The next step…
There is no need to feel daunted by the number of parts and in front of you, we have
compiled this straight forward, step-by-step guide to make sure that assembling your furniture
is as easy as 1, 2, 3.
Before you begin, we advise that you check that you have everything you need to get started.
TOP TIP
Find a space to spread these out acr re you begin
assembling them. Lay each panel down in position, ready to build.
It is recommended that two people assemble this product together.
The full list of furniture parts, res and as well as the tools you will need for assembly,
can be found on page 2 and 3 of this manual.
TOP TIP
re that you have them all prepared
and familiarise yourself with each component, to make things easier
when you are putting it all together.
Safety and Care Advice
IMPORTANT re your safety!
Please take the time to read and understand these instructions before assembling your
furniture.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials way from children to avoid danger of suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Make sure that you allow enough space to move around when assembling your furniture.

Panels - plan view
Panel -
exploded view
Parts & Fittings for the Ontario 2 Drawer Bedside (30149680)
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Left side panel
335 x 482mm
1Right side panel
335 x 482mm
4
Left front leg
60 x 513mm
2
Left rear leg
60 x 513mm
3
Right front leg
60 x 513mm
5
Right rear leg
60 x 513mm
6
Front bottom support
355 x 40mm
7Front bottom slat
355 x 75mm
8Back bottom slat
355 x 90mm
9
Top panel
480 x 420mm
10 Back panel
390 x 455mm
11
Drawer back x2
306 x 160mm
12 Left drawer side x2
350 x 160mm
13
Right drawer side x2
350 x 160mm
14
Drawer bottom x2
342 x 313mm
15
Drawer front x2
350 x 206mm
16

Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 08451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Ready?
Follow this step-by-step guide
Fittings
Metal cam pin
x 24
Metal cam
x 24
Foot glide
x 4
Plastic corner
x 2
Cross slot screwdriver Hammer Tape measure
Tools required
The use of power tools to assemble the product is not recommended due to the risk of
3
1
40mm Screw
x 8
A
30mm Wooden dowel
x 8
B
x 12
C
22mm Handle screw
x 4
H
D
Handle
x 2
G
E
F
x 32
I
Drawer slide
x 4
J
K
16mm Screw
x 8
L M
50mm Wooden dowel
14mm Screw Drawer track
x 4
Note: Insert metal
dowels as far as shown.
2
3
D
5
6
5
2
3 6
Bottom end
D
D
D
DD
D
D D
D D
D
DL
L
L
L
L
B
B
B
B
B

4
3
9
8
1
4
2
10
7
8
Note: Insert metal
dowels as far as shown.
D
D
D
DD
FF
F
F
M
BB
B B
B
CC
C C
C
C
C C
C C
C
C
C
x2

5
5
4
1
Front edge
This end to
the front edge
of the panel
Ensure the cam is pressed fully
into the hole and arrow pointing
towards to the edge
6
4
5
1
4
Front edge
4
3
1
2
1
4
F
F
IF
F
F
I
E
E
E
E
EE
EE
E
x4
F

6
6
8
7
Ensure the cam is pressed fully into
the hole and arrow pointing
towards the top edge
10
1
4
Fit the panels together with help
Ensure the cam is pressed fully into
the hole and arrow pointing
towards the edge
9
8
1
4
8
9
2
1
3
4
5
6
9
8
EE
E
E
E
E
EE
EE

7
9
10
14
J
Note: Insert metal
dowels as far as shown.
This end to
the front end
of the panel
x2
x2
11
12
13
14
x2
J
13
14
11
13
14
11
Front end Front end
16
K
K K K
K
KK
K
K
D
D
DD
DF
F
F
F
F
F
J
J
A
A
A
A
A
A
x8
13
x2
JF
F
F
J

8
12
13
14
x2
15
16
x2
Ensure the cam is pressed
fully into the hole and arrow
pointing towards the edge
x2
G
13
14
14
Please make sure both left and right
slides are engaged at the same time.
Fit both drawer slides into drawer
tracks straight and evenly, not
tilting to one side.
Nearly There!
16
13
14
13 14
E
E
E
E
E
GH
H
H
H
JI
I
J

9
I
I
I

Finally, we hope you enjoy your furniture for
many years to come and thanks again
for your purchase.
dunelm.com
Care and maintenance
Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste
disposal centre.