Durr Dental Primo User manual

Primo, Duo, Trio, Quattro, Quattro
Tandem
EN Montage- und Gebrauchsanweisung
0297
5152100003L02 2305V004

The current version of the installation and operating instructions is available in the Download Center:
http://qr.duerrdental.com/5152100003
©Dürr Dental SE

Contents
Important information
1About this document .. . . . . . . . . . . . . 3
1.1 Warnings and symbols .. . . . . . . 3
1.2 Copyright information .. . . . . . . . 4
2 Safety .. . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Intended purpose .. . . . . . . . . . . 4
2.2 Intended use .. . . . . . . . . . . . . . . 4
2.3 Improper use .. . . . . . . . . . . . . . . 4
2.4 General safety information .. . . . . 5
2.5 Specialist personnel .. . . . . . . . . 5
2.6 Electrical safety .. . . . . . . . . . . . . 5
2.7 Notification requirement of seri-
ous incidents .. . . . . . . . . . . . . . . 5
2.8 Only use original parts .. . . . . . . . 5
2.9 Transport .. . . . . . . . . . . . . . . . . . 5
2.10 Disposal .. . . . . . . . . . . . . . . . . . 6
Product description
3Overview .. . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Scope of delivery .. . . . . . . . . . . . 7
3.2 Optional items .. . . . . . . . . . . . . . 7
3.3 Wear parts and replacement
parts .. . . . . . . . . . . . . . . . . . . . . 7
4Technical data .. . . . . . . . . . . . . . . . . . . 8
4.1 Primo .. . . . . . . . . . . . . . . . . . . . 8
4.2 Duo .. . . . . . . . . . . . . . . . . . . . . . 9
4.3 Duo .. . . . . . . . . . . . . . . . . . . . . . 11
4.4 Trio .. . . . . . . . . . . . . . . . . . . . . . 12
4.5 Quattro .. . . . . . . . . . . . . . . . . . . 14
4.6 Quattro Tandem .. . . . . . . . . . . . 16
4.7 Filter .. . . . . . . . . . . . . . . . . . . . . 17
4.8 Ambient conditions .. . . . . . . . . . 17
4.9 Distance between rubber feet .. . 18
4.10 Type plate .. . . . . . . . . . . . . . . . . 18
4.11 Evaluation of conformity .. . . . . . 18
5 Operation .. . . . . . . . . . . . . . . . . . . . . . 19
5.1 Duo with membrane drying unit .. 19
Assembly
6 Requirements .. . . . . . . . . . . . . . . . . . . 20
6.1 Installation/setup room .. . . . . . . 20
6.2 Setup .. . . . . . . . . . . . . . . . . . . . 20
6.3 Information about electrical con-
nections .. . . . . . . . . . . . . . . . . . 20
7 Transport .. . . . . . . . . . . . . . . . . . . . . . . 21
8 Quattro Tandem assembly and instal-
lation .. . . . . . . . . . . . . . . . . . . . . . . . . . 21
9 Installation .. . . . . . . . . . . . . . . . . . . . . . 22
9.1 Remove the transport locks .. . . 22
9.2 Establishing the compressed air
connection .. . . . . . . . . . . . . . . . 22
9.3 Pressure reducer .. . . . . . . . . . . 22
9.4 Place a collector tray underneath .. 22
9.5 Electrical connections .. . . . . . . . 22
10 Commissioning .. . . . . . . . . . . . . . . . . . 23
10.1 Check the motor protection
switch .. . . . . . . . . . . . . . . . . . . . 23
10.2 Checking the switch-on/cut-off
pressure .. . . . . . . . . . . . . . . . . . 24
10.3 Draining the condensation water .. 24
10.4 Adjusting the rate of flow at the
pressure reducer .. . . . . . . . . . . . 24
11 Adjustment options .. . . . . . . . . . . . . . 25
11.1 Adjusting the pressure switch .. . 25
11.2 Adjusting the motor protection
switch .. . . . . . . . . . . . . . . . . . . . 25
12 Circuit diagrams .. . . . . . . . . . . . . . . . . 27
12.1 1/N/PE AC 110-127 V, 230 V
layout .. . . . . . . . . . . . . . . . . . . . 27
12.2 3/N/PE AC 400 V layout .. . . . . . 27
12.3 3/N/PE AC 230 V layout, Quat-
tro Tandem .. . . . . . . . . . . . . . . . 28
Usage
13 Operation .. . . . . . . . . . . . . . . . . . . . . . 29
13.1 Switching the unit on/off .. . . . . . 29
Contents
5152100003L02 2305V004 EN | 1

14 Maintenance .. . . . . . . . . . . . . . . . . . . . 30
14.1 Maintenance schedule .. . . . . . . . 30
14.2 Wear parts and replacement
parts .. . . . . . . . . . . . . . . . . . . . . 30
14.3 Changing the filter .. . . . . . . . . . . 31
14.4 Checking the safety valve .. . . . . 32
15 Taking out of use .. . . . . . . . . . . . . . . . 32
15.1 Taking the unit out of use .. . . . . 32
15.2 Storage of the unit .. . . . . . . . . . 33
Troubleshooting
16 Tips for operators and service techni-
cians .. . . . . . . . . . . . . . . . . . . . . . . . . . 34
Appendix
17 Handover record .. . . . . . . . . . . . . . . . . 36
18 Country representatives .. . . . . . . . . . . 38
Contents
2 | EN 5152100003L02 2305V004

Important information
1 About this document
These installation and operating instructions rep-
resent part of the unit.
The manufacturer and the distributor will
not offer any guarantee or accept any lia-
bility for the safe operation and the safe
functioning of the unit if the instructions
and information in these installation and
operating instructions are not complied
with.
The German version of the installation and oper-
ating instructions is the original manual. All other
languages are translations of the original manual.
These installation and operating instructions
apply to:
Primo
REF: 5152-01
Duo
REF: 5252100001; 5252-01; 5252-01/Service;
5252-51; 5252100024
Trio
REF: 5352-01; 5352100001; 5352100013
Quattro
REF: 5452-51; 5452100001
Quattro Tandem
REF: 4682-52; 4682-53
1.1 Warnings and symbols
Warnings
The warnings in this document are intended to
draw your attention to possible injury to persons
or damage to machinery.
The following warning symbols are used:
General warning symbol
Warning – dangerous high voltage
Warning – hot surfaces
Warning - automatic start-up of the unit
The warnings are structured as follows:
SIGNAL WORD
Description of the type and source of
danger
Here you will find the possible conse-
quences of ignoring the warning
❯Follow these measures to avoid the
danger.
The signal word differentiates between four levels
of danger:
–DANGER
Immediate danger of severe injury or death
–WARNING
Possible danger of severe injury or death
–CAUTION
Risk of minor injuries
–NOTICE
Risk of extensive material/property damage
Other symbols
These symbols are used in the document and on
or in the unit:
Note, e.g. specific instructions regarding
efficient and cost-effective use of the unit.
Observe the operating instructions.
Disconnect all power from the unit.
Refer to the accompanying electronic
documents.
Air
Dispose of correctly in accordance with
EU Directive 2012/19/EU (WEEE).
CE labelling with the number of the noti-
fied body
Order number
Serial number
Medical device
Health Industry Bar Code (HIBC)
Important information
5152100003L02 2305V004 EN | 3

Manufacturer
1.2 Copyright information
All circuits, processes, names, software pro-
grams and units mentioned in this document are
protected by copyright.
The Installation and Operating Instructions must
not be copied or reprinted, neither in full nor in
part, without written authorisation from the copy-
right owner.
2 Safety
The unit has been developed and designed in
such a way that dangers are effectively ruled out
if used in accordance with the Intended Use.
Despite this, the following residual risks can
remain:
– Personal injury due to incorrect use/misuse
– Personal injury due to mechanical effects
– Personal injury due to electric shock
– Personal injury due to radiation
– Personal injury due to fire
– Personal injury due to thermal effects on skin
– Personal injury due to lack of hygiene, e.g.
infection
WARNING
The development of emphysema
Soft tissue can be damaged as a result
of careless handling.
❯Do not dwell in the area being treated
for any longer than is necessary.
2.1 Intended purpose
The compressor is designed to supply com-
pressed air for dental applications.
2.2 Intended use
The air supplied by the compressor is suitable for
driving dental tools.
The compressed air generated by the compres-
sor is delivered to the pipeline system of the sur-
gery. The entire compressed air system must be
designed in such a way that the quality of the
compressed air generated by the compressor is
not impaired.
With this prerequisite, the air provided by the
compressor is also suitable for blow-drying tooth
preparations.
2.3 Improper use
Any use of this appliance / these appliances
above and beyond that described in the Installa-
tion and Operating Instructions is deemed to be
incorrect usage. The manufacturer cannot be
held liable for any damage resulting from incor-
rect usage. The operator will be held liable and
bears all risks.
Important information
4 | EN 5152100003L02 2305V004

WARNING
Risk of explosion due to ignition of
combustible materials
❯Do not operate the unit in any rooms in
which inflammable mixtures may be
present, e.g. in operating theatres.
❯The unit is not suitable for providing an air sup-
ply to respirators.
❯This unit is not suitable for drawing up fluids or
for compressing aggressive gases or poten-
tially explosive gases.
2.4 General safety information
❯Always comply with the specifications of all
guidelines, laws, and other rules and regula-
tions applicable at the site of operation for the
operation of this unit.
❯Check the function and condition of the unit
prior to every use.
❯Do not convert or modify the unit.
❯Comply with the specifications of the Installa-
tion and Operating Instructions.
❯The Installation and Operating Instructions
must be accessible to all operators of the unit
at all times.
2.5 Specialist personnel
Operation
Unit operators must use their training and knowl-
edge to ensure safe and correct handling.
❯Instruct or have every operator instructed in the
handling of the unit.
The following groups are not permitted to
operate or use a commercially operated unit:
– People without the necessary experience and
knowledge
– People with reduced physical, sensory or men-
tal capabilities
– Children
Installation and repairs
❯Have the manufacturer or a qualified company
authorised by the manufacturer perform
mounting, new installations, modifications,
expansions and repairs.
2.6 Electrical safety
❯Observe and comply with all the relevant elec-
trical safety regulations when working on the
unit.
❯Replace any damaged cables or plugs immedi-
ately.
2.7 Notification requirement of
serious incidents
The operator/patient is required to report any
serious incident that occurs in connection with
the device to the manufacturer and to the com-
petent authority of the Member State in which
the operator and/or patient is established/resi-
dent.
2.8 Only use original parts
❯Only use accessories and optional articles
named or authorised by the manufacturer.
❯Only use only original wear parts and replace-
ment parts.
The manufacturer and distributor accept
no liability for damages or injury resulting
from the use of non-approved accesso-
ries, optional accessories, or from the use
of non-original wear parts or replacement
parts.
The use of non-approved accessories,
optional accessories or non-genuine wear
parts / replacement parts (e.g. mains
cables) can have a negative effect in
terms of electrical safety and EMC.
2.9 Transport
The original packaging provides optimum protec-
tion for the unit during transportation.
If required, the original packaging for the unit can
be ordered.
The manufacturer and the distributor do
not accept liability, even during the war-
ranty period, for damage during transpor-
tation due to improper packaging.
❯Only transport the unit in its original packaging.
❯Keep the packing materials out of the reach of
children.
Important information
5152100003L02 2305V004 EN | 5

2.10 Disposal
The unit must be disposed of properly.
Within the European Union, the unit must
be disposed of in accordance with EU
Directive 2012/19/EU (WEEE).
❯If you have any questions about the correct
disposal of parts, please contact your dental
trade supplier.
An overview of the waste keys for Dürr
Dental products can be found in the
download area:
http://qr.duerrdental.com/P007100155
Important information
6 | EN 5152100003L02 2305V004

Product description
3 Overview
3.1 Scope of delivery
The following items are included in the scope of
delivery (possible variations due to country-spe-
cific requirements and/or import regulations):
Primo 230 V, 1~, with membrane dry-
ing unit .. . . . . . . . . . . . . . . . . . . . . . . . 5152-01
Duo 110 V, 1~, with membrane
drying unit .. . . . . . . . . . . . . . . . . . . 5252100001
Duo 230 V, 1~, with membrane drying
unit .. . . . . . . . . . . . . . . . . . . . . . . . . . . 5252-01
Duo 230 V, 1~, with mem-
brane drying unit .. . . . . . . . . . 5252-01/Service
Duo 230 V, 1~, with membrane
drying unit .. . . . . . . . . . . . . . . . . . . 5252100024
Duo 400 V, 3~, with membrane drying
unit .. . . . . . . . . . . . . . . . . . . . . . . . . . . 5252-51
Trio 230 V, 1~, with membrane drying
unit .. . . . . . . . . . . . . . . . . . . . . . . . . . . 5352-01
Trio 230 V, 1~, with membrane
drying unit .. . . . . . . . . . . . . . . . . . . 5352100001
Trio 230 V, 1~, with membrane
drying unit .. . . . . . . . . . . . . . . . . . . 5352100013
Quattro 400 V, 3~, with membrane
drying unit* .. . . . . . . . . . . . . . . . . . . . . 5452-51
Quattro 400 V, 3~, with membrane
drying unit* .. . . . . . . . . . . . . . . . . . 5452100001
Quattro Tandem 230 V, 3~, with mem-
brane drying unit .. . . . . . . . . . . . . . . . . 4682-52
Quattro Tandem 400 V, 3~, with mem-
brane drying unit .. . . . . . . . . . . . . . . . . 4682-53
– Fabric reinforced hose
– Hose nozzle
– Hose clamp
– Short information
– Appliance log book
– Collector tray
3.2 Optional items
The following items can optionally be used with
the unit; these items do not bear the CE mark:
Pressure reducer .. . . . . . . . . . . . . . 6040-992-00
Fine filter .. . . . . . . . . . . . . . . . . . . . 1610-121-00
Wooden cabinet for sound insula-
tion of Primo and Duo Compres-
sors .. . . . . . . . . . . . . . . . . . . . . . . 5150-500-00
Wooden cabinet for for sound
insulation of Duo Tandem, Trio and
Quattro Compressors .. . . . . . . . . . 4251-500-00
3.3 Wear parts and replacement
parts
The following working parts must be replaced at
regular intervals (refer also to "Maintenance");
these articles do not bear the CE mark:
Air intake filter .. . . . . . . . . . . . . . . . 0832-982-00
Fine filter .. . . . . . . . . . . . . . . . . . . . 1610-121-00
Virus bacteria filter .. . . . . . . . . . . . . 1650100172
Coalescence filter .. . . . . . . . . . . . . 1650200323
To configure the required filters or filter
sets, you can also use our filter configura-
tor at:
www.duerrdental.com/filterkonfigurator
Any repairs exceeding routine mainte-
nance may only be carried out by quali-
fied personnel or our service.
Information about replacement parts is
available from the portal for authorised
specialist dealers at:
www.duerrdental.net
If the mains cable of this unit is damaged
it must only be replaced by an original
mains cable from the manufacturer.
Product description
5152100003L02 2305V004 EN | 7

4 Technical data
4.1 Primo
Electrical data 5152-01
Nominal voltage V 230
Mains frequency Hz 50 60
Nominal current at 8 bar (0.8 MPa) A 4.4 4.3
Motor protection switch, recommended
setting A 5 4.5
Type of protection IP 24
Mains fuse* A 10
* Circuit breaker fuse characteristics B, C or D in accordance with EN 60898-1
General technical data
Pressure tank volume l 20
Suction power, approx. l/min 105 125
Delivery at 5 bar (0.5 MPa)* l/min 61 71
Pressure build-up phase 0-7.5 bar (0-0.75
MPa), approx. s 155 130
Duty cycle % 100
Start-up pressure bar (MPa) 6 (0.6)
Cut-off pressure bar (MPa) 7.8 (0.78)
Cut-off pressure, max. adjustable bar (MPa) 9.5 (0.95)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1)
Pressure dew point at 7 bar (0.7 MPa)** °C £+5
Dimensions (H x W x D) *** cm 69 x 49 x 47
Weight kg 45
Noise level ****
without sound insulation
with sound insulation
dB(A)
dB(A)
65
49
66
50
* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744
Air purity
Air quality in accordance with ISO 22052 chap. 5.3 fulfilled
Classification
Medical Device Class (MDR) IIa
Product description
8 | EN 5152100003L02 2305V004

4.2 Duo
Electrical data 5252-01
5252-01/Service
5252100024
5252-51
Rated voltage V 230 400
Mains frequency Hz 50 60 50 60
Nominal current at 8 bar (0.8 MPa) A 6.3 7.0 3.1 2.5
Motor protection switch, recommended
settings A 6.5 7.6 3.1 2.5
Type of protection IP 24 IP 24
Mains fuses * A 10 10
Max. permissible mains impedance in
accordance with EN 61000‑3‑11 ** W£0.142 -
* Circuit breaker fuse characteristics B, C or D in acc. with EN 60898-1
** Mains impedance at 6 switching cycles per hour. If the number of switching cycles per hour is
higher a lower mains impedance is required.
General technical data
Pressure tank volume l 20 20
Suction power, approx. l/min 210 255 210 255
Delivery at 5 bar (0.5 MPa)* l/min 125 145 125 145
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) approx. s 70 60 70 60
Duty cycle % 100 100
Cut-In pressure bar (MPa) 6 (0.6) 6 (0.6)
Cut-out pressure bar (MPa) 7.8 (0.78) 7.8 (0.78)
Cut-off pressure, max. adjustable bar (MPa) 9.5 (0.95) 9.5 (0.95)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1) 10 (1)
Pressure dew point at 7 bar (0.7 MPa)** °C £+5 £+5
Dimensions (H x W x D) *** cm 69 x 49 x 47 69 x 49 x 47
Weight kg 50 50
Noise level ****
without sound insulation
with sound insulation
dB(A)
dB(A)
66
51
68
-
66
51
68
50
* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744
Air purity
Air quality in accordance with ISO 22052 chap. 5.3 fulfilled
Product description
5152100003L02 2305V004 EN | 9

Classification
Medical Device Class (MDR) IIa
Product description
10 | EN 5152100003L02 2305V004

4.3 Duo
Electrical data 5252100001
Nominal voltage V 110-115 110-127
Mains frequency Hz 50 60
Nominal current at 8 bar (0.8 MPa) A 14.1-14.6 14.2-13.3
Motor protection switch, recommended
setting
A
17 16
Type of protection IP 24
Mains fuse* A 20
* Circuit breaker fuse characteristics B, C or D in accordance with EN 60898-1
General technical data
Pressure tank volume l 20
Suction power, approx. l/min 210 255
Delivery at 5 bar (0.5 MPa)* l/min 125 145
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) approx. s 70 60
Duty cycle % 100
Cut-In pressure bar (MPa) 6 (0.6)
Cut-out pressure bar (MPa) 7.8 (0.78)
Cut-off pressure, max. adjustable bar (MPa) 9.5 (0.95)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1)
Pressure dew point at 7 bar (0.7 MPa)** °C £+5
Dimensions (H x W x D) *** cm 69 x 49 x 47
Weight kg 50
Noise level ****
without sound insulation dB(A) 66 68
* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744
Air purity
Air quality in accordance with ISO 22052 chap. 5.3 fulfilled
Classification
Medical Device Class (MDR) IIa
Product description
5152100003L02 2305V004 EN | 11

4.4 Trio
Electrical data 5352-01
5352100001
5352100013
Rated voltage V 230
Mains frequency Hz 50
Nominal current at 8 bar (0.8 MPa) A 8.6
Motor protection switch, recommended
settings A 8.6
Type of protection IP 24
Mains fuses * A 10
Max. permissible mains impedance in
accordance with EN 61000‑3‑11 W£0.078
* Circuit breaker fuse characteristics B, C or D in acc. with EN 60898-1
General technical data
Pressure tank volume l 50
Suction power, approx. l 315
Delivery at 5 bar (0.5 MPa)* l/min 181
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) c. s 140
Duty cycle % 100
Cut-In pressure bar (MPa) 6 (0.6)
Cut-out pressure bar (MPa) 7.8 (0.78)
Cut-off pressure, max. adjustable bar (MPa) 9.5 (0.95)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1)
Pressure dew point at 7 bar (0.7 MPa)** °C £+5
Dimensions (H x W x D) *** cm 76 x 74 x 52
Weight kg 80
Noise level ****
without sound insulation
with sound insulation
dB(A)
dB(A)
67
49
* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744
Air purity
Air quality in accordance with ISO 22052 chap. 5.3 fulfilled
Product description
12 | EN 5152100003L02 2305V004

Classification
Medical Device Class (MDR) IIa
Product description
5152100003L02 2305V004 EN | 13

4.5 Quattro
Electrical data 5452-51
5452100001
Nominal voltage V 400
Mains frequency Hz 50 60
Nominal current at 8 bar (0.8 MPa) A 4.4 4.8
Motor protection switch, recommended
setting A 5.0 5.0
Type of protection IP 24
Mains fuse* A 10
Max. permissible mains impedance in
accordance with EN 61000‑3‑11** W£0.24
* Circuit breaker fuse characteristics B, C or D in accordance with EN 60898-1
** Mains impedance at 6 switching cycles per hour. If the number of switching cycles per hour is
higher, a lower mains impedance is required.
General technical data
Pressure tank volume l 50
Suction power, approx. l/min 420 505
Delivery at 5 bar (0.5 MPa)* l/min 258 293
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) c. s 95 80
Duty cycle % 100
Cut-In pressure bar (MPa) 6 (0.6)
Cut-out pressure bar (MPa) 7.8 (0.78)
Cut-off pressure, max. adjustable bar (MPa) 9.5 (0.95)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1)
Pressure dew point at 7 bar (0.7 MPa)** °C £+5
Dimensions (H x W x D) *** cm 76 x 74 x 52
Weight kg 85
Noise level ****
without sound insulation
with sound insulation
dB(A)
dB(A)
69
53
70
54
* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744
Air purity
Air quality in accordance with ISO 22052 chap. 5.3 fulfilled
Product description
14 | EN 5152100003L02 2305V004

Classification
Medical Device Class (MDR) IIa
Product description
5152100003L02 2305V004 EN | 15

4.6 Quattro Tandem
Electrical data 4682-52 4682-53
Nominal voltage V 230 / 3~ 400 / 3~
Mains frequency Hz 50 60 50 60
Nominal current at 8 bar (0.8 MPa) A 15.2 16.6 8.8 9.6
Motor protection switch, recommended
setting A 9 9 5 5
Type of protection IP 24 IP 24
Mains fuse* A 20 20
Max. permissible mains impedance in
accordance with EN 61000‑3‑11** W£0.445 £0.18
* Circuit breaker fuse characteristics B, C or D in accordance with EN 60898-1
** Mains impedance at 6 switching cycles per hour. If the number of switching cycles per hour is
higher, a lower mains impedance is required.
General technical data
Pressure tank volume l 90 90
Suction power, approx. l/min 845 1010 845 1010
Delivery at 5 bar (0.5 MPa)* l/min 516 586 516 586
Pressure build-up phase 0 - 7.5 bar (0 -
0.75 MPa) c. s 90 80 90 80
Duty cycle % 100 100
Start-up pressure bar (MPa) 6.5 (0.65) 6.5 (0.65)
Cut-off pressure bar (MPa) 8.5 (0.85) 8.5 (0.85)
Cut-off pressure, max. adjustable bar (MPa) 9.5 (0.95) 9.5 (0.95)
Safety valve, maximum permissible oper-
ating pressure bar (MPa) 10 (1) 10 (1)
Pressure dew point at 7 bar (0.7 MPa)** °C £+5 £+5
Dimensions (H x W x D) *** cm 76 x 102 x 62 76 x 102 x 62
Weight kg 170 170
Noise level **** dB(A) 72 73 72 73
* Delivery without membrane drying unit, at +20°C and 1013 mbar (0.1 MPa)
** Value determined at an ambient temperature of +40 °C
*** Values without accessories and add-on parts
**** Noise level in accordance with ISO 3744
Air purity
Air quality in accordance with ISO 22052 chap. 5.3 fulfilled
Classification
Medical Device Class (MDR) IIa
Product description
16 | EN 5152100003L02 2305V004

4.7 Filter
Filter mesh size
Air intake filter µm 3
Fine filter µm 3
Virus bacteria filter µm 0.01
Coalescence filter µm 0.01
4.8 Ambient conditions
Ambient conditions during storage and transport
Temperature °C -10 - +55
Relative humidity % < 95
Ambient conditions during operation
Temperature °C +10 - +40
Ideal temperature °C +10 - +25
Relative humidity % < 95
Product description
5152100003L02 2305V004 EN | 17

4.9 Distance between rubber feet
Distances between the rubber feet for different
pressure vessel volumes:
b
a
a (cm) b (cm)
20 l 23 27
50 l 32.5 45
90 l 32.5 59
4.10 Type plate
Complete system
The type plate of the overall system is located on
the mounting plate for the compressor unit.
1
1 Type plate for the complete system
Compressor unit
The type plate of the compressor unit is located
on the crankcase below the cylinder.
1
1 Compressor unit type plate
Membrane drying unit
The type plate of the membrane drying unit is
located on the side of the membrane drying unit.
1
1 Membrane drying unit type plate
4.11 Evaluation of conformity
This device has been subjected to conformity
acceptance testing in accordance with the cur-
rent relevant European Union guidelines. This
equipment conforms to all relevant requirements.
Product description
18 | EN 5152100003L02 2305V004