DW DWC-V6763TIR User manual

10/08
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Analog High Definition
Outdoor Dome Camera
DWC-V6763TIR

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

Table of Contents
3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Surface Mount Installation instructions
Connecting to Monitors 13
Corner Mount Installation Instructions 12
Pendant Mount Installation Instructions 11
Wall Mount Installation Instructions 10
Junction Box Installation Instructions
Control Board
4
5
6
7
8
9
14
16
Adjusting the Camera Axis
15
17-32
33
34-35
36-37
Adjusting the Camera Angle

4
FEATURES*
Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
1/2.7” CMOS Sensor
1080P Resolution at 30fps
Varifocal P-Iris Lens 2.8~12mm
Smart IR™ with Intelligent Camera Sync. 100ft Range
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter
Secondary Video-BNC Output (While UTP in use)
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)
IP66 Certified (Weather Resistant)

PARTS & DESCRIPTION*
7
8
1
BNC Cable
DC12V Cable
Bottom Case
Camera Gimbal
Upper Case
Dome Cover
2
3
4
6
5Cover Screws (x4)
Side Port for Cabling
6
1
3
5
2
4
7
8
5

6
DIMENSIONS IN MILLIMETERS (IN)*
47.0 1.9
144.0 5.7
61.8 2.4
145.0 5.7
117.0 4.6
125.0 4.9

7
INSIDE THE BOX*
Included with Camera:
1
2
3
4
5
User Manual
Mounting Template
4 Machine Screws and 4 Dry Wall Anchors
Secondary Video-BNC Cable
L-Key
10/08
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Analog High Definition
Outdoor Dome Camera
DWC-V6763WTIR

8
SURFACE MOUNT INSTALLATION INSTRUCTIONS*
1. Use the camera or mounting template to
mark and drill the necessary holes in the
wall or ceiling.
2. Pull wires through and make
connections.
3. Using the four (4) included screws,
mount and secure the camera to the wall
or ceiling.
4. Adjust the camera’s Pan and Tilt and
Lens. See pages 15-16 for more
information.
5. Use the joystick to adjust the OSD
menu. See pages 17-28 for more
information.
6. Attach the camera housing to the
camera base using the assembly screws.

9
JUNCTION BOX INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Use the dry wall anchors and
machine screws to mount the
junction box and rubber
gasket to the wall.
Insert wires through the
wall and make the
appropriate connections.
Attach the camera to the
junction box using the
machine screws.
Attach the camera housing
to the junction box using the
assembly screws.
1 2 3
4 5

10
WALL MOUNT INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Insert the wires from the
camera through the wall
mount housing.
Attach the camera to
the wall mount housing.
Use the mounting template to
make pilot holes. Use the dry
wall anchors and machine screws
to attach the assembly to the wall.
Attach the camera housing
to the fixture.
1 2 3
4 5