Dyna-Glo Premier DGG424CNP User manual

1
Français p. XX
Español p. XX
Rev. 10/22/2019
3 BURNER
PREMIER GAS GRILL
Model #DGG424CNP/DGG424CNP-D/
DGG424RNP/DGG424RNP-D
ATTACH YOUR RECEIPT HERE
Serial Number _____________________________ Purchase Date ______________________
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday
or e-mail us at [email protected].
Français p. 30
Español p. 59

2
Assembler/Installer: This manual contains important information necessary for the proper
assembly and safe use of this appliance. Read and follow all warnings and instructions before
assembling and using this appliance. Leave these instructions with the consumer.
Consumer/User: Follow all warnings and instructions when using this appliance.
Retain these instructions for future reference.
TABLE OF CONTENTS
Safety Information ...................................................................................................................... 3
Package Contents ...................................................................................................................... 5
Hardware Contents .................................................................................................................... 6
Preparation ................................................................................................................................. 6
Assembly Instructions ................................................................................................................ 7
Operation Instructions ................................................................................................................. 17
Care and Maintenance ................................................................................................................. 22
Troubleshooting ........................................................................................................................... 25
Warranty ...................................................................................................................................... 27
Replacement Parts List .............................................................................................................. 28
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. Open lid.
4. If odor continues, keep away from
the appliance and immediately call your
local re department.
1. Do not store or use gasoline or
other ammable liquids or vapors
in the vicinity of this or any other
appliance.
2. An LP (liquid propane) cylinder not
connected for use shall not be stored
in the vicinity of this or any other
appliance.
3. This grill is for outdoor use only
and shall not be used in a building,
garage, under overhangs or any other
enclosed area.
4. Do not leave a lit grill unattended.
Keep children and pets away from the
grill at all times.
WARNING
DANGER

3
DANGER
CAUTION
• Do not use in an explosive atmosphere. Keep grill area clear and free from combustible
materials, gasoline and other ammable vapors and liquids.
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product, please call customer service at:
1-877-447-4768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday.
• Never use charcoal or lighter uid with the grill.
• Do not use gasoline, kerosene or alcohol for lighting.
• The LP gas cylinder used with this appliance must be:
(a) Constructed and marked in accordance with the Specications for LP-Gas Cylinders
of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada,
CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods;
and Commision, as applicable; and
(b) Provided with a listed overlling prevention device.
(c) Provided with a cylinder connection device compatible with the connector for outdoor
cooking appliances. This grill is not intended to be used in or installed on recreational
vehicles and/or boats.
• Never keep a lled container in a hot car or car trunk. Heat will cause the gas pressure to
increase, which may open the relief valve and allow gas to escape.
• Always open grill lid slowly and carefully as heat and steam trapped within the grill can burn
you severely.
SAFETY INFORMATION
This product and the fuels used to operate this product (liquid propane), and the products of
combustion of such fuels, can expose you to chemicals including benzene, which is known
to the State of California to cause cancer and reproductive harm.
For more information go to www.p65Warnings.ca.gov
WARNING

4
SAFETY INFORMATION
• Do not place the grill under overhead
combustible construction or awnings.
Minimum clearance from sides and
back of unit to combustible construction,
36 inches (914.4mm) from sides and
back.
NOTE: The installation must conform with
local codes or, in the absence of local
codes, with either the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, Natural
Gas and Propane Installation Code,
CSA B149.1, or Propane Storage and
Handling Code, B149.2.
CAUTION
• Do not store or use gasoline or other ammable liquids or vapors in the vicinity of this or any
other appliance.
• An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
• This grill is for use with propane gas only (propane cylinder not included).
• Never attempt to attach this grill to the self-contained propane system of a boat, camper trailer,
motor home or house.
• Do not attempt to move the grill while it is lit or when it is hot. The casters should be locked
when not moving the grill.
• Do not use the grill unless it is completely assembled and all parts are securely fastened and
tightened.
• Keep all combustible items and surfaces at least 36 inches (91.44 cm) away from the grill at all
times.
• Do not touch metal parts of grill until it has completely cooled (about 45 minutes) to avoid
burns, unless you are wearing protective gear (pot holders, gloves, BBQ mittens, etc…).
• Do not alter this grill in any manner.
• Clean and inspect the hose before each use. If there is evidence of abrasion, wear, cuts,
or leaks, the hose must be replaced prior to operating the appliance. The replacement hose
assembly will be that which is specied by the manufacturer.
• Move gas hoses as far away as possible from hot surfaces and dripping hot grease.
• Keep the grill’s valve compartment, burners and circulating air passages clean. Inspect the grill
before each use. Do not obstruct the ow of gas or ventilation air.
• The use of alcohol, prescription or non-prescription drugs may impair the operator’s ability to
properly assemble or safely operate the grill.
• Do not leave a lit grill unattended. Keep children and pets away from the grill at all times.
• Do not place this grill on any type of tabletop surface. The grill should be placed on a at and
level surface.
• Do not use the grill in high winds.
WARNING
36in 36in
914.4mm
914.4mm

5
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Lid Handle 1
BFirebox Assembly 1
C Warming Rack 1
D Cooking Grate 2
EHeat Tent 3
F Grease Cup 1
G Grease Pan 1
H Knob 3
I Left Side Shelf Assembly 1
J Left Side Shelf Front Assembly 1
K Right Side Shelf Assembly 1
L Right Side Shelf Front Assembly 1
M Cart Left Side Panel Assembly 1
PART DESCRIPTION QUANTITY
N Cart Right Side Panel Assembly 1
O Cart Rear Panel 1
P Cart Bottom Shelf Assembly 1
Q Caster 2
R Caster With Brake 2
S Cart Front Brace 1
TLeft Door Assembly 1
U Door Handle 2
VRight Door Assembly 1
W Magnet 1
X Temp Gauge 1
Y Temp Gauge Bezel 1
C
D
E
F
G
J
M
T
U
S
WR
QU
V
N
L
K
B
A
X
Y
I
H
O
P

6
HARDWARE CONTENTS (shown actual size)
M6x16
Bolt
Qty. 33
M6x25
Bolt
Qty. 2
M6
Spring Washer
Qty. 2
M4x12
Bolt
Qty. 16
M6
Plain Washer
Qty. 2
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list on previous page and hardware contents above. If any part is missing or damaged, do
not attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 50 minutes with 2 people.
Tools Required for Assembly and Leak Testing (not included): Phillips screwdriver, Spray bottle
CAUTION
THIS UNIT IS HEAVY. Two people required for safe assembly.
Two people required for safe assembly. Some parts may contain sharp edges. Wear protective
gloves if necessary. Read and follow all safety statements, warnings, assembly instructions and
use and care instructions before attempting to assemble and use.
CCAA BB DD
FF
EE
Wrench
Qty. 1

7
ASSEMBLY INSTRUCTIONS
1. Attach the two casters (Q) and the two casters
with brake (R) to the cart bottom shelf
assembly (P) with the wrench (FF).
Hardware Used
Wrench x 1
2. Attach the magnet (W) to the cart bottom shelf
assembly (P) with two M4x12 bolts (BB).
Hardware Used
BB M4x12 Bolt x 2
2
FF
1
P
Q
R
FF
BB
W

8
ASSEMBLY INSTRUCTIONS
3. Pre-assemble four M6x16 bolts (AA) onto
the cart bottom shelf assembly (P) and do not
tighten them. Make sure to leave a 5mm gap
between the bolt and the panel. Then hang
the cart left side panel assembly (M) and the
cart right side panel assembly (N) onto the
bolts and tighten the four bolts.
4. Attach the cart front brace (S) to the cart left
side panel assembly (M) and the cart right side
panel assembly (N) with four M6x16 bolts (AA).
3
4
Hardware Used
Hardware Used
AA
AA
M6x16 Bolt
M6x16 Bolt
x 4
x 4
AA
N
M
AA
SM
N

9
ASSEMBLY INSTRUCTIONS
5. Pre-assemble four M6x16 bolts (AA) onto the
cart left side panel assembly (M) and the cart
right side panel assembly (N) and do not tighten
them. Make sure to leave a 5mm gap between
the bolt and the panel. Then hang the cart rear
panel (O) onto the bolts and tighten the four
bolts.
Attach the cart rear panel (O) to the cart bottom
shelf assembly (P) with one M6x16 bolt (AA).
6. Attach the door handle (U) to the left door
assembly (T) and the right door assembly (V)
with four M6x16 bolts (AA).
5
6
AA
T
U
V
U
Hardware Used
Hardware Used
AA
AA
M6x16 Bolt
M6x16 Bolt
x 5
x 4
AA
O

10
ASSEMBLY INSTRUCTIONS
8. Pre-assemble two M4x12 bolts (BB) onto the
left side shelf front assembly (J) and do not
tighten them. Make sure to leave a 5mm gap
between the bolt and the panel. Then hang the
left side shelf assembly (I) onto the bolts and
tighten the two bolts.
Attach the left side shelf assembly (I) to the
left side shelf front assembly (J) with one
M4x12 bolt (BB).
7. Attach the left door assembly (T) and the right
door assembly (V) to the cart left side panel
assembly (M) and the cart right side panel
assembly (N) with eight M4x12 bolts (BB).
7
8
Hardware Used
Hardware Used
BB
BB
M4x12 Bolt
M4x12 Bolt
x 8
x 3
BB
T
V
BB
I
J

11
ASSEMBLY INSTRUCTIONS
9. Pre-assemble two M4x12 bolts (BB) onto the
right side shelf front assembly (L) and do not
tighten them. Make sure to leave a 5mm gap
between the bolts and the panel. Then hang
the right side shelf assembly (K) onto the bolts
and tighten the two bolts.
Attach the right side shelf assembly (K) to the
right side shelf front assembly (L) with one
M4x12 bolt (BB).
10. Attach the lid handle (A) to the rebox
assembly (B) with two M6 plain washers (DD),
two M6 spring washers (EE) and two M6x25
bolts (CC).
10
L
9
Hardware Used
BB M4x12 Bolt x 3
BB
Hardware Used
CC
M6 Plain Washer
M6x25 Bolt
x 2
x 2
DD
M6 Spring Washer x 2
EE
K
A
B
EE
DD
CC

12
ASSEMBLY INSTRUCTIONS
11. Remove pre-assembled wing nut and plain
washer from the temp gauge (X), then attach
the temp gauge (X) and the temp gauge bezel
(Y) to the rebox assembly (B). Secure the
temp gauge (X) with the wing nut and plain
washer removed earlier in this step.
11
12. Attach the three knobs (H) to the valve stems. 12
Y
X
H

13
13
14
ASSEMBLY INSTRUCTIONS
13. Carefully place the rebox assembly (B) onto
the cart left side panel assembly (M) and the
cart right side panel assembly (N). Adjust the
rebox assembly (B) so that the holes in the
rebox assembly (B) are aligned with holes in
the tabs of the cart left side panel assembly (M)
and the cart right side panel assembly (N).
Note: Make sure the gas hose/regulator
assembly is outside the cart. Secure the rebox
assembly (B) with four M6x16 bolts (AA). AA
14. Insert two M6x16 bolts (AA) in right side of
the rebox assembly (B) as shown, leaving
5mm of threads exposed. Align key hole in the
right side shelf assembly (K) with the two bolts
just inserted in the rebox assembly (B), and
insert four M6x16 bolts (AA) in the remaining
holes in the rebox assembly (B). Adjust the
rebox assembly (B) correctly, then tighten all
bolts.
Hardware Used
Hardware Used
AA
AA
M6x16 Bolt
M6x16 Bolt
x 4
x 6
AA
AA
AA

14
ASSEMBLY INSTRUCTIONS
15
16
15. Insert two M6x16 bolts (AA) in left side of
the rebox assembly (B) as shown, leaving
5mm of threads exposed. Align key hole in
the left side shelf assembly (I) with the two
bolts just inserted in the rebox assembly (B),
and insert four M6x16 bolts (AA) in the
remaining holes in the rebox assembly (B).
Adjust the rebox assembly (B) correctly, then
tighten all bolts.
16. Place three heat tents (E) over each burner.
AA
Hardware Used
AA M6x16 Bolt x 6
AA AA
E

15
ASSEMBLY INSTRUCTIONS
17. Put two cooking grates (D) and one warming
rack (C) in place. 17
18. Put the grease pan (G) and grease cup (F) into
place. 18
C
D
G
F

16
19. Open the left door assembly (T) and the
right door assembly (V). Place LP gas cylinder
(sold separately) into the nesting hole located
on the cart bottom shelf assembly (P). Rotate
the LP gas cylinder until the hose/regulator
coupling aligns with the threaded valve of the
cylinder. Hand tighten the hose/regulator
coupling to the threaded valve of the LP gas
cylinder.
Tighten the tank screw clockwise in the
front of the cart until the LP gas cylinder is
secured in place inside the nesting hole of the
cart bottom shelf assembly (P)
19
Fully Assembled
Tank
Screw LP Gas Cylinder
ASSEMBLY INSTRUCTIONS

17
OPERATION INSTRUCTIONS
CHECKING FOR LEAKS
After all connections are made, check all connections and ttings on the LP gas tank valve, gas hose
and regulator for leaks with a water and soap solution.
To prevent re or explosion while testing for a leak:
• Always perform leak test prior to lighting the grill.
• Do not smoke while testing for a leak.
• Always perform leak tests outdoors in a well-ventilated area.
• Do not use any source of ame while testing for leaks.
• Do not use the grill until any and all leaks are corrected.
• If you are unable to correct a leak, disconnect the propane supply and call a gas appliance service
dealer.
PERFORM LEAK TEST
• Prepare leak test solution by 50/50 ratio of liquid dish soap and water.
Total solution required is approximately 2 - 3 ounces (70 - 90 ml).
Put leak test solution in a spray bottle.
• Ensure all control knobs are in the O OFF position.
• Connect the gas hose to the gas supply.
• Open the LP gas tank valve.
• Spray leak test solution on all gas carrying connections and ttings. Presence of bubbles at areas
of applied test solution indicates a gas leak. If leaks are detected or you smell or hear gas, shut off the
gas supply valve immediately and repair or replace the defective part. Do not use the grill until
all leaks are corrected.
WARNING
ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO
PREVENT FIRE, DAMAGE AND/OR INJURY.
CAUTION
Only use the regulator and hose assembly provided! If a replacement is necessary, please call
our customer service center. Do not use replacement parts that are not intended for this grill.

18
OPERATION INSTRUCTIONS
CONNECTING GAS CYLINDER
The propane gas supply cylinder to be used must be constructed and marked in accordance with the
Specications for LP Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National
Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous
Goods; and Commission, as applicable; and provided with a listed overlling prevention device.
Use only 20-pound cylinders (height: 18.11 inches, tank diameter: 9.84 inches, foot diameter: 8.03 inches)
equipped with a cylinder connection device compatible with the connection for outdoor cooking appli-
ances.
The cylinder must include a collar to protect the cylinder valve. The gas cylinder should not be dropped
or handled roughly!
If the appliance is not in use, the gas cylinder must be disconnected. Storage of an appliance indoors
is permissible ONLY if the cylinder is disconnected and removed from the appliance. Cylinders must
be stored outdoors out of the reach of children and must not be stored in a building, garage or any
other enclosed area. Your cylinder must never be stored where temperatures can reach over 125°F.
Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of
dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or
plugs may result in leakage of propane.
Before connection, be sure that there is no debris caught in the outlet of the gas cylinder, outlet of the
regulator valve or in the outlet of the burner and burner ports. Connect regulator valve and
hand-tighten rmly. Keep the propane cylinder valve closed and disconnect the propane cylinder from
the regulator valve when the grill is not in use.
DO NOT obstruct the ow of combustion air and ventilation air to the grill. The propane cylinder must
be arranged for vapor withdrawal and equipped with a listed overlling prevention device. Please use
the proper cylinder orientation to provide vapor withdrawal. NOTE: The cylinder must be fully upright
for the cylinder to have vapor withdrawal only.
CAUTION
a. Do not store a spare LP-gas cylinder under or near this appliance.
b. Never ll the cylinder beyond 80 percent full.
c. If the information in (a) and (b) is not followed exactly, a re causing death or serious
injury may occur.

19
OPERATION INSTRUCTIONS
NOTE: Other cylinders may be acceptable for use with this appliance provided they are compatible
with the appliance nesting hole and retention means. Refer to Step 19 of the Assembly Instructions
for correct cylinder to cylinder holder connection.
WARNING
ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO
PREVENT FIRE, DAMAGE AND/OR INJURY.
WARNING
In the connection process, make sure:
• the regulator inlet connector mates with the cylinder valve outlet properly, safely and rmly, and;
• the LP gas hose does not come in contact or remain in contact with the rebox.
CONNECTING THE LP TANK
1. The knob on the LP tank must be closed. Make sure that the knob is turned clockwise to a
full stop. The cylinder supply system must be arranged for vapor withdrawal.
2. Check that the control knob on the control unit is turned off.
3. Remove the protective cap from the LP tank valve and coupling nut.
4. Hold the regulator in one hand and insert the nipple into the valve
outlet. Be sure the nipple is centered in the valve outlet. The coupling
nut connects to the large outside threads on the valve outlet. Use
care – do not cross thread the connection.
5. Hand-tighten the coupling nut clockwise until it comes to a full
stop. Firmly tighten by hand only. Do not use tools.
To Disconnect: Fully close the tank valve by turning clockwise.
Turn the coupling nut counterclockwise until the regulator assembly detaches.

20
OPERATION INSTRUCTIONS
Lighting The Grill
Before rst use:
Remove all hangings or plastic straps, if present. Before you cook on your new gas grill, it is important
to clean your grill with heat. To do this, operate the grill for approximately 15 minutes with the lid closed
and the control knob in the highest position. This will clean the internal parts by burning off any residue
and odor from the manufacturing process.
WARNING
Do not lean over grill when lighting. Read instructions before lighting. Do not put pots on the
sear side burner. Using pots on the sear side burner will result in high carbon monoxide levels.
CAUTION
If the ame extinguishes accidentally during ignition or operation, immediately TURN OFF the
cylinder valve and then TURN OFF the control knob.
1. Check that the control knobs are in the OFF position.
2. Open the tank valve fully by turning it counter-clockwise.
3. Open the lid during the lighting process.
4. Depress and turn the control knob counter-clockwise from the OFF position, past the ignite
position, to the HIGH position. You may need to repeat this several times to ignite the burner.
If ignition does not occur in 5 seconds, turn the control knob(s) to the OFF position, wait 5 minutes, and
repeat the lighting procedure.
If the burner still does not light, check that there is gas in the cylinder and follow the match lighting
instructions. Check the Troubleshooting Guide on page 26 for more information.