Dyna-Glo Signature DGSS443CB User manual

1
Heavy-Duty
Compact Barrel
Charcoal Grill
MODEL #DGSS443CB-D /
DGSS443CB
Français p. 19
Español p. 37
ATTACH YOUR RECEIPT HERE
Serial Number ________________________________ Purchase Date _________________________________
70-10-596 Rev. 4/18/19
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m. CST,
Monday – Friday or email [email protected].

2
TABLE OF CONTENTS
Safety Information ...................................................................................................................... 2
Package Contents ...................................................................................................................... 4
Hardware Contents .................................................................................................................... 5
Preparation ................................................................................................................................. 5
Assembly Instructions ................................................................................................................ 6
Operation Instructions ................................................................................................................. 14
Care and Maintenance ................................................................................................................ 15
Warranty ...................................................................................................................................... 16
Replacement Parts List .............................................................................................................. 17
Please read and understand this entire manual before attempting to assemble, operate, or
install the product. If you have any questions regarding the product, call our customer
service department at 1-877-447-4768, 8:00 a.m.- 4:30 p.m. CST, Monday - Friday or email
[email protected].
Use caution when lifting and moving the unit to avoid back strain or back injury. Do not move
the unit while it is in use.
•DO NOT operate the unit near or under ammable or combustible materials such as decks,
porches or carports.
• A minimum clearance to combustible construction is 36 in. (91.4 cm) from sides and back.
•DO NOT operate the unit under overhead construction.
•DO NOT use this grill as a heater.
• Operate the unit on a stable, level, noncombustible surface such as asphalt, concrete, or
solid ground.
•DO NOT operate the unit on ammable material such as carpet or wood deck.
SAFETY INFORMATION

3
SAFETY INFORMATION
• Use caution when assembling and operating this unit to avoid cuts and scrapes from edges.
• DO NOT use this product in a manner other than its intended purpose. It is NOT intended for
commercial use. It is NOT intended to be installed or used in or on a recreational vehicle
and/or boats.
• DO NOT store this unit near gasoline or other combustible liquids or where other combustible
vapors may be present.
• DO NOT use, store or operate this unit in an area accessible to children or pets. Store this unit in a
dry protected location.
• DO NOT leave the unit unattended while in use.
• DO NOT leave hot ashes unattended, until the unit cools completely.
• DO NOT move the unit while in use, or while ashes are still hot. Allow the unit to cool completely
before moving or storing.
• NEVER use gasoline, kerosene, Zippo/Ronson lighter uid, or other highly volatile uids as a starter.
• Always cook your food on the grate after the ame is burned out.
• Dispose of cold ashes by wrapping them in heavy-duty aluminum foil and placing in a
noncombustible container. Make sure that there are no other combustible materials in or near
the container.
• If you must dispose of ashes in less time than it takes for the ashes to completely cool down,
remove the ashes from the unit using heat-resistant gloves along with long metal tongs or
replace shovel. Place the coals in aluminum foil and soak them completely with water before
disposing of them in a noncombustible container.
• Allow the unit to cool completely before conducting any routine cleaning or maintenance.
• This product will be hot during and after use. Use insulated oven mitts, or gloves, for protection
from hot surfaces or splatter from cooking liquids.
• Grease or other liquids inside the grease cup will be hot after using this appliance. Allow the
grease cup to completely cool before removing or disposing. If the grease cup must be removed
before it's allowed to completely cool, use heat resistant gloves or mitts for removal or disposal.
• Use caution when opening the lid of the unit while in operation. Keep hands, face and body safe
from hot steam or are-ups. DO NOT inhale smoke.
• DO NOT wear loose clothing while operating the unit. Tie back long hair while operating the unit.
• ALWAYS wear shoes that fully cover your feet while operating the unit.
• NEVER use glassware, plastic or ceramic cookware on or in the unit. Use metallic cookware only.
• Use of accessories not intended for this unit is not recommended and may lead to injury or
property damage.
WARNING
This product and the fuels used to operate this product (charcoal or wood), and the
products of combustion of such fuels, can expose you to chemicals including carbon black,
which is known to the State of California to cause cancer, and carbon monoxide, which is
known to the State of California to cause birth defects or other reproductive harm.
For more information go to www.p65Warnings.ca.gov
CALIFORNIA PROPOSITION 65

4
PACKAGE CONTENTS
I
PART DESCRIPTION QUANTITY
A Lid 1
B Temperature Gauge 1
C Smoke Stack Damper 1
D Lid Handle 1
E Smoke Stack 1
F Smoke Stack Gasket 1
G Grill Body 1
H Side Handle 1
I Grease Cup Support 1
J Left Leg - Rear 1
K Bottom Shelf 1
L Left Leg - Front 1
M Right Leg - Rear 1
PART DESCRIPTION QUANTITY
N Right Leg - Front 1
O Wheel Axle 1
P Wheels 2
Q Offset Smoker Box Support 1
R Front Shelf Bracket - Left 1
S Front Shelf Bracket - Right 1
T Front Shelf 1
U Side Access Door Latch 1
V Side Damper 1
W Side Access Door 1
X Charcoal Grates 2
Y Cooking Grates 3
A
A
C
E
N
B
D
M
S
H
Q
LP
R
F
G
J
IK
TA
U
WV
Y
X
O

5
HARDWARE CONTENTS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents above. If any part is missing or damaged, do
not attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Phillips Screwdriver, Adjustable Wrench
BB CC
M6 x 12
Bolt
Qty. 31
DD
M6 Nut
Qty. 28
AA EE
M12 Nut
Qty. 2
M6 Lock Nut
Qty. 1
M6 Flat
Washer
Qty. 16
FF GG HH
M5 x 13
Bolt
Qty. 1
M5 Nut
Qty. 1
M6 x 14
Bolt
Qty. 1

6
ASSEMBLY INSTRUCTIONS
CAUTION:This unit is HEAVY! Do not attempt to
handle this unit without assistance!
1. Remove the pre-installed bolt and washer from
the left lid hinge on the grill body (G) and slide the
lid (A) off the grill body hinges.
2. Attach the left front leg (L) and right front leg (N)
using four M6 x 12 bolts (AA), four M6 nuts (BB)
and four M6 at washers (CC) per leg.
Hardware Used
AA M6 x 12mm
Bolt x 8
1
2
N
BB
G
AA
BB M6 Nut x 8
A
L
CC
CC M6 Flat Washer x 8
Pre-installed
Hardware

7
ASSEMBLY INSTRUCTIONS
3. Before attaching the rear legs, insert the bottom
shelf (K) posts into the holes located on all four
legs. WIth the bottom shelf (K) securely in place,
attach the left rear leg (J) and right rear leg (M)
using four M6 x 12 bolts (AA), four M6 nuts (BB)
and four M6 at washers (CC), per leg.
4. Insert the wheel axle (O) through the holes in the
right front (N) and right rear leg (M) and attach the
left and right wheel (P) using one M12 nut (DD)
per side.
P
N
M
K
DD
3
4
Hardware Used
DD M12 Nut x 2
AA
O
Hardware Used
AA M6 x 12mm
Bolt x 8
BB M6 Nut x 8
CC M6 Flat Washer x 8
J
BB
CC
M

8
ASSEMBLY INSTRUCTIONS
5. Attach side handle (H) to the left side of the grill
body (G) using four M6 x 12 bolts (AA) and four
M6 nuts (BB).
6. Place the smoke stack gasket (F) between the
grill body (G) and the smoke stack (E) and attach
using four M6 x 12 bolts (AA) and four M6 nuts (BB).
F
G
6
Hardware Used
AA M6 x 12mm
Bolt x 4
H
G
BB
5
BB M6 Nut x 4
AA
BB
Hardware Used
AA M6 x 12mm
Bolt x 4
BB M6 Nut x 4
E
AA

9
ASSEMBLY INSTRUCTIONS
7. Attach the smoke stack damper (C) using the
pre-installed spring and nut.
8. Insert the end of the grease cup support (I) into
the hole located on the bottom of the smoker
body (G). Thread the support through the hole
until the support is hanging as shown.
Note: This grill does not include a container for
catching grease or liquids from inside the smoker
body. Use a discarded aluminum can with
minimum diameter of 2 1/4" (58mm) and slide
the top lip of the can onto the grease cup support
(I) as shown. See Page 3 for disposing the can
after use.
C
7
G
8
I

10
ASSEMBLY INSTRUCTIONS
9. Attach the right shelf bracket (S) to the grill
body (G), using two M6 x 12 bolts (AA) and two
M6 nuts (BB), and insert the shelf support wire
into the bracket, as shown. Insert the shelf
supports into the left shelf bracket (R), before
securing the bracket with two M6 x 12 bolts (AA)
and two M6 nuts (BB).
10. Attach the temperature gauge (B) by inserting the
probe through the threaded opening on the lid (A)
and turning clockwise. Do not remove the
pre-installed nut prior to attaching the gauge.
NOTE: The alignment of the temperature gauge
can be adjusted by turning the pre-installed nut
clockwise (or counter-clockwise) prior to installing.
Attach the lid handle (D) to the lid (A) using two
pre-installed bolts & nuts and at washers
10
S
D
9
Hardware Used
AA M6 x 12mm
Bolt x 4
A
B
BB AA
BB M6 Nut x 4
G
R
S

11
ASSEMBLY INSTRUCTIONS
11. Attach the lid assembly (A) to the hinges on the
grill body (G) using the pre-installed bolt
and washer.
12. Attach the side damper plate (V) to the inside of
the the access door (W) using one M6 x 12 bolt
(AA) and one M6 lock nut (EE).
Attach the door latch (U) to the outside of the
access door (W) using one M5 x 12 bolt (GG) and
one M5 nut (HH).
U
11
12
G
A
Pre-installed
Hardware
EE
V
W
GG
AA
HH
Hardware Used
AA M6 x 12mm
Bolt x 1
EE M6 Lock Nut x 1
GG M5 x 13mm
Bolt x 1
HH M5 Nut x 1

12
ASSEMBLY INSTRUCTIONS
13. Screw one M6 x 14 shoulder bolt (FF) into the grill
body (G). Attach the access door (W) to the grill
body (G) by sliding the hinge rods into the hinge
openings on the grill body (G).
Latch the access door (W) by pivoting the door
latch (U) onto the M6 x 14 bolt on the grill body (G).
14. Install the charcoal grates (X) on the bottom
support rails inside the grill body (G). Install the
cooking grates (Y) on the top support rails inside
the grill body (G).
14
13
Hardware Used
FF M6 x 12mm
Bolt x 1
X
Y
G
U
W
G
FF

13
ASSEMBLY INSTRUCTIONS
15. Attach the offset support bracket (Q) to the right
front (N) and rear leg (M) using two M6 x 12
bolts (AA).
Note: This bracket is used to support Dyna-Glo
smoker box model DGSS287CB-D (Sold Separately)
Q
15 M
N
AA
Hardware Used
AA M6 x 12mm
Bolt x 2

17
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-877-447-4768, 8:00 a.m. –4:30 p.m.
CST, Monday – Friday or email [email protected].
PART DESCRIPTION PART #
1 Lid assembly (without
Dyna Glo badge and
temperature gauge) 70-01-545
2 Temperature gauge 70-01-518
3 Smoke stack damper 70-01-522
4 Lid handle 70-01-584
5 Smoke stack 70-01-548
6 Smoke stack gasket 70-01-549
7 Grill body (without
door assembly) 70-01-558
8 Side handle - Grill 70-01-550
9 Grease cup support 70-01-554
10 Left leg - Rear 70-01-585
11 Bottom shelf 70-01-595
12 Left leg - Front 70-01-586
13 Right leg - Rear 70-01-587
14 Right leg - Front 70-01-588
PART DESCRIPTION PART #
15 Wheel axle 70-01-596
16 Wheel - Left/Right(1pc.) 70-01-516
17 Offset smoker
box support 70-01-589
18 Front shelf
bracket - Left 70-01-559
19 Front shelf
bracket - Right 70-01-566
20 Front shelf 70-01-597
21 Side access door latch 70-01-592
22 Side damper plate 70-01-593
23 Side access door 70-01-594
24 Charcoal grate(1pc) 70-01-547
25 Cooking grate(1pc) 70-01-598
26 Dyna Glo badge 70-01-562
n/a Instruction manual 70-10-596
n/a Hardware pack 70-09-520
11

18
70-10-596 Printed in China
A
5
3
1
6
4
2
7
10
8
9
12 A
15
13
17
14
16
20
18
21
19
23
22
REPLACEMENT PARTS LIST
11
24
25
26