DYNABREEZE FA-23181 Guide

TRADE QUALITY SINCE 1995
MODEL FA-23181
Instruction
User Manual
& Warranty T
INDUSTRIAL 450MM
CAUTION: Read the Assembly & Safety Instructions before operating and
retain for future reference
WALL FAN

2450MM WALL FAN
Thank you &
Congratulations on
the purchase of your
Dynabreeze Industrial
450mm Wall Fan
To nd out more information on this product,
please visit www.dynabreeze.com.au or contact:
Tradeware
Address 45 Birralee Rd, Regency Park SA 5010
Phone au 1300 658 494 nz 0800 689 960
Email [e-mail]
Website www.tradeware.com.au
SPECIFICATIONS Model FA-23181
Voltage 220-240V
Frequency 50Hz
Motor Power 120W
Air Volume 120m3/min
Max Speed 1350 RPM
Fan Speed 3
Diameter 450mm
Product Weight 8.5KG
T

INSTRUCTION USER MANUAL & WARRANTY 3
OPERATION CONDITIONS & SAFETY PRECAUTIONS
WARNING: When using electrical appliances, basic safety precautions should be
followed to reduce the risk of re, electric shock and injury to persons or property.
• To avoid a hazard due to instability of the
appliance, it must be placed on an even,
at surface.
• Do not operate this appliance with a
damaged cord or plug after the appliance
has been damaged in any manner.
• Before each use, check for any damaged
parts, and have it replaced or repaired by
the manufacturer or a qualied electrician.
• Connect to properly grounded power outlet
only. No other appliance should be plugged
into the same outlet.
• Do not run the power cord over carpeting
or other heat insulators. Do not cover the
cord. Keep cord away from trac areas.
• Switch o and unplug the appliance before
moving, cleaning or making any repairs or
servicing.
• Keep safety guards/grilles in place and
do not operate the machine with them
removed.
WARNING: Touching of moving blades can
cause serious injury.
• Do not insert ngers or anything through
the grille.
• Do not wear jewellery or loose clothing that
could be caught by the rotating blades.
• Never leave the appliance running
unattended, turn the power o.
WARNING: Exercise caution and use
reasonable supervision when appliance is
used near children to ensure that they do
not play with the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge.
• Keep the area around the fan clear and
suitable distance from objects that may be
suctioned into the fan.
• Pack away in a dry place in the original
carton when not in use.
WARNING: Do not use the appliance
in a bathroom or in the immediate
surroundings of a bath, a shower or a
swimming pool. Keep all parts away from
water or any other liquids.
CLEANING: Turn o, remove any dust build
up with a soft brush, wipe the surface of
the unit with a damp soft cloth using a mild
detergent (no harsh chemicals).

4450MM WALL FAN
PARTS IDENTIFICATION
A Power Cord
B Wall Mount Plate
C Safety Grille
D Fan Blade
E Electric Motor
F Speed Control Dial
G White Cord: On/O Speed
Control Cord
A
E
B
J
K
LIG
F
H
C
D
H Red Cord: Oscillation Control
I Oscillation Arm
J Motor Head
K Motor Neck
L Tilt Adjustment

INSTRUCTION USER MANUAL & WARRANTY 5
1. Locate the bag that contains the wall
mounting hardware.
2. Select location to place it on the wall.
NOTE: Ensure power supply is nearby and
power cord is not too tight or in a position to
interfere with oscillating function.
3. Ensure the wall is suitable to support
the fan:
- If mounting to a plastered wall, then the
wall mount must be tted to a stud behind
the plaster wall using the screws provided.
- If mounting to a brick or masonry wall,
ensure plugs and screws used are suitable.
- Suitable xings must be used and must
support a minimum of 8.5kg. Always check
the suitability of plugs and screws for
installation before use.
NOTE: The fan must be mounted vertically.
TIP: To assist in mounting the fan, a wall
mounting drilling diagram is provided on
the last page of this manual. Pre-drilling
and xing the mounting screws can be
performed without having to hold the fan
in place.
Drill
ASSEMBLY & OPERATION
Assembling the fan
Tools required
plaster
studs
brick/
masonry

6450MM WALL FAN
4. Once the 4 xings are in place, mount the
fan over the screw heads and slide down
into position so the screw heads do not slip
out of the mounting bracket hole.
5. Unscrew the large gold bolt from the
oscillation arm, line up the connecting rod
and re-insert the washer and bolt back into
the arm.
After reading these instructions, plug the
power cord into the power outlet.
The fan can be turned on by pulling down
on the white cord. Pulling once will turn the
control knob to speed 1, pull again for speed
2 and again for speed 3. The fourth pull will
turn the fan o and go back to 0.
Oscillation
Pull on the red cord once to oscillate and a
second time to stop oscillation.
Adjustments: Vertical Tilt Adjustment
Grip the top and bottom of the grille rmly
and tilt to the desired position. If too
dicult, loosen the centre bolt slightly to
give more exibility and re-tighten.
Assembling the fan cont. Operating the fan

WARRANTY
Under the Australian Consumer Law (ACL) or NZ Consumer
Guarantees Act (CGA), you are entitled to a 12 month
replacement or refund for product failure and compensation
for any other reasonably foreseeable loss or damage.
Tradeware oers a 3 Year Warranty. The additional
warranties, terms and conditions are outlined on the
website www.dynabreeze.com.au under the Support tab.
Under Support you can also Register your product upon
purchase and enjoy the peace of mind of knowing your
product is registered should anything happen.
If the unit fails to operate eciently, is broken or other
problems arise, unplug and do not operate. Ask for advice by
calling Tradeware.
To Claim, the fan should be returned to the place of purchase
or via the website within the warranty period.
Such claims must include:
• Details of the alleged defect or fault;
• Evidence of the claim; and
• Proof of purchase documentation which clearly shows the
date and place of purchase.
Please visit www.dynabreeze.com.au for more details
Tradeware
45 Birralee Road, Regency Park
South Australia 5010
[e-mail]
1300 658 494
www.tradeware.com.au
Due to continual product development, please note the information and content
provided may not be nal and may be subject to changes.
Please
Recycle

74mm
80mm
6
12
Wall Mounting - Drilling Diagram
Cut out this diagram to use as a drilling guide