DynaLock 3000LC Series User manual

Page 8
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
Page 1
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
FOR PRODUCT SUPPORT AND PARTS
ORDERING INFORMATION CONTACT:
DynaLock Corp.
705 Emmett Street
Bristol, CT 06010
Bus: [phone] Toll-Free
[phone]
Fax: [phone]
DYNALOCK ON THE INTERNET:
E-mail: [email protected]
Website: www.dynalock.com
CSFM
NYC Mea #23-92-E
PLEASE DELIVER THIS MANUAL
TO THE END-USER UPON COMPLETION
OF THE INSTALLATION
Familiarize yourself with the door and frame conditions. The lock must mount rigidly to the face of the door frame
header. The door mounted armature is supplied with an adjustable mounting bracket and hardware that allows it
to pivot slightly to compensate for reasonable misalignment.
NOTE: If this lock is supplied with the DSM option be certain that disc magnets are present inside the
armature housing.
Care must be taken that the lock face and armature face are kept free of dirt, rust, paint, or any other obstruction
which may interfere with the lock and armature making good contact. These faces may be cleaned with a non-
abrasive pad and wiped with an oil dampened cloth.
The Series 2011 is a 1200 pound holding force
(the 3000LC is a 1500 pound holding force)
electromagnetic lock designed to secure a single
outswing door. The lock requires both installation
procedures as described herein and in the separate
wiring instructions included.
The illustration to the left shows a typical
installation on a single outswing door.
HANDLING
MECHANICAL INSTALLATION
ELECTRICAL INSTALLATION
After mechanical installation is complete the lock needs to be wired to a 12 or 24 VDC/VAC power source. Once low
voltage power is supplied the unit is fully operational. All other wiring is for selected options. Refer to the separate
wiring instructions included for further information.
INSTALLATION DESCRIPTION
2011/3000LC LOCK ASSEMBLY
ARMATURE
GWXT Auxiliary Lock

Page 2
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
Page 7
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
MODEL #2011/3000LC
BILL OF MATERIALS
(1) 2011/3000LC LOCK ASSEMBLY
(2) ARMATURE
(2) ARMATURE HOUSING
(2) HARDWARE KIT
(1) 1/8” BALL HEAD HEX WRENCH
(1) MOUNTING TEMPLATE
(1) INSTALLATION MANUAL
(1) WIRING MANUAL
REQUIRED TOOLS
(1) Electric Drill
(1) #2 Phillips Screw Driver
(1) Soft Faced Mallet
(1) Hammer
(1) Center Punch
(1) 3/16” Hex Wrench
(1) Pencil & Tape
Drill Bits: 1/8”, 17/64”, 11/32”, 1/2”, 9/16”, 21/32”
HARDWARE KIT CONTENTS
(P/N 301316)
General Information........................................... 1
Bill Of Materials................................................. 2
Using The Template........................................... 3
Mounting The Armature..................................... 4
Mounting The Lock............................................ 5
Exploded Parts View.......................................... 6
Exploded Parts Legend..................................... 7
Support............................................................... 8
TABLE OF CONTENTS
QTY. ITEM DESCRIPTION
7 Baseplate Mounting Screws #10x1” phillips pan head sheet metal screw
7 Baseplate Mounting Screws #10-24x1/2” phillips pan head machine screw
1 Armature Mounting Screw 5/16-18x2” hex at head machine screw, turned
4 Armature Housing Screws #8x1” phillips at head sheet metal screw
4 Armature Housing Screws 8-32x3/8” phillips at head machine screw
1 Armature Spacer 3/8”Dx0.235”L spacer
1 Steel Washer 1/4” at zinc washer
1 Door Spacer 5/8”Dx1-11/16”L spacer
1 Sex Nut 5/16-18 sex nut
NOTE: For further parts clarication refer to the Exploded Parts View on page 6 or consult factory.
PARTS LEGEND
******** Part of Hardware Kit (301316)
Refer to Page 6 for parts locations.
ITEM
1
2
3
4
5
6
7
DESCRIPTION
Baseplate
PART #
300110
#10 x 1” PPH SMS ********
Housing Assembly 300107
Access Cover 300009
Plug Button
5/16-18x2” FHS Turned
Armature 300373
ITEM DESCRIPTION PART #
Door Spacer
9Washer Flat Zinc
10 Sex Nut
11 Armature Housing 301334
12 Lock Mounting Bolt
13 Armature Spacer
14 #8x1” FHS SMS
15 8-32x3/8” FHS MS U/C
********
********
********
********
********
********
********
********
********
8
10-24 x ½” PPH M ********
2

Page 6
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
Page 3
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
Inspect the door frame and determine if an angle bracket or ller plate will be required for installation. The lock will
require a 2” wide header stop for a suitable mounting surface.
MOUNTING CONSIDERATIONS
USING THE TEMPLATE
*See Price Book or Call DynaLock Corp.
NORMAL
MOUNTING
FILLER PLATE
REQUIRED*
SPACER PLATE
REQUIRED*
ANGLE BRACKET
REQUIRED*
1. Fold the template on the dotted line to form a 90 degree
angle. Scoring the template with a straight edge and a
screwdriver will make it fold easier.
2. With the door closed and in the latched position, from the
push side, place the template against the header and door on
the frame, and tape in place.
3. Transfer all hole locations to both the door and header
with a center punch, then remove the template from the door.
4. Referring to the template drill two 1/8” diameter lock mounting holes (or tap for 10-24) and one 9/16” diameter
wiring hole in the top of the frame, at all transferred locations. Remaining mounting holes will be drilled after the
lock is rst mounted and adjusted (page 6).
5. Drill the remaining transferred holes in the face of the door to accept the armature following the instructions on
page 4 for your specic door type.
9/16" DIA. WIRING HOLE
1/8" DIA. DRILL
PLACEAGAINSTHEADER
FOLD ON DOTTED LINE
PLACEAGAINSTJAMB
OPPOSITE HINGES FOR
R.H.R. DOOR INSTALLATION
PLACEAGAINSTJAMB
OPPOSITE HINGES FOR
L.H.R. DOOR INSTALLATION
1/8”DIA.ARMATURE HOUSING MOUNTING
SCREW HOLES 1”DEEP(4 REQ'D.)
11/32" DIA. DRILLFORTHRU BOLT MOUNTING OR
5/16”-18TAPFOR MOUNTING ON REINFORCED DOOR
(SEE INSTRUCTIONS)
2011/3000LC SERIES
ELECTROMAGNETIC
LOCK
DynaLock
Emergency Tech Supportis available Monday - Friday, 5:00PM-8:00PM (EST)
By Calling: Mike @ [phone] or Glen @ [phone]
CARDBOARD
TEMPLATE
EXPLODED PARTS VIEW
ARMATURE
ASSEMBLY
(TYPICAL)
LEGEND ON NEXT PAGE
2-3/16” 2-3/16”
1
2
3
4
5
15
12 10 8
7
13
9
6
11
14

Page 4
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
Page 5
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
MOUNTING THE ARMATURE
Mount the Armature Housing to the door using four (4) #8 x 1” sheet metal screws or #8-32 x 3/8” machine
screws.
Place the Armature inside the Armature Housing and secure using the proper hardware, according to the above
illustrations. Firmly tighten the Armature mounting screw with a 3/16” hex wrench.
Failure to properly secure the Armature to the door could result in serious injury or possible security
breach.
From the three illustrations below select the one that resembles your door type and follow the instructions for drilling
the Armature mounting screw hole. (See Template)
Drill four (4) 1/8” dia. holes for #8 x 1” sheet metal screws or drill and tap for #8-32 x 3/8” machine screws (See
Template).
GLASS AND ALUMINUM
OR HOLLOW METAL DOOR SOLID CORE DOOR REINFORCED DOOR
Drill an 11/32” diameter hole
through the door. From the
sex nut side only enlarge the
hole to 21/32” diameter.
Drill an 11/32” diameter hole
through the door. From the
sex nut side drill 1/2” diameter
hole to 1” depth.
Drill a 17/64” diameter hole
and tap for 5/16-18 thread
ARMATURE
STEEL WASHER
ARMATURE
SCREW
DOOR
SPACER
SEX
NUT
21/32"
ARMATURE
HOUSING
ARMATURE
SPACER
STEEL WASHER
ARMATURE
SCREW
ARMATURE
SPACER
1/2"
1"
ARMATURE
ARMATURE
HOUSING
STEEL WASHER
ARMATURE
SCREW
ARMATURE
SPACER
5/16"-18 THREAD
ARMATURE
ARMATURE
HOUSING
1/4” MIN
MOUNTING THE LOCK
1) Mounting the baseplate to the header:
Separate the baseplate from the lock housing with the Hex wrench.
Place the baseplate against the header with the counter sunk slots
visible, and the large slot over the wire hole. Using an electric drill
with a Philips bit attach the baseplate to the header at both slotted
locations with the screws provided. Tighten the screws just snug
enough to allow for nal adjustments.
2) Aligning the lock and armature:
Close and latch the door. Temporarily mount the lock to
the baseplate and verify the lock face and the armature
are making full contact for the entire length of the arma-
ture. If any adjustment required gently tap the baseplate
with a soft mallet until full contact is achieved. Mark
the two baseplate corner locations lightly with a pencil
for reference. Remove the lock from the baseplate and
tighten both adjustment screws. Drive the remaining 5
screws into the header using the baseplate as a physical
template. Screw heads must not project above the baseplate.
3) Attaching the lock to the baseplate:
Using the Hex wrench, permanently fasten the lock to
the baseplate with the two 1/4” - 20 x 1-1/4” machine
screws removed in step 1. Install the plug caps over
the mounting screws with a small mallet.
BASEPLATE
HEADER
ARMATURE &
LOCKFACE MUST
MAKE FULL CONTACT
MAGLOCK
SHOULD BE PARALLEL
LOCK
PLUG
CAPS
SOCKET HEAD
MOUNTING SCREWS