Dyson purifier cool Gen1 User manual

User manual
SV12 JN.00000 PN.000000-00-00 00.00.00 VERSION NO.01
Contents
Assembling your machine
Getting started
Power and continuous monitoring
Information menu
Auto mode
Airflow speed
Oscillation
Night mode and Sleep timer
Changing your HEPA+Carbon filter
Resetting your HEPA+Carbon filter life
Looking after your machine
Dyson Purifier Cool Gen1 logo
Front view of the Dyson
Purifier Cool Gen1 fan,
showing the amplifier loop
and mesh filter cover, screen
below the loop amplifier and
outer cover release button
on the side.
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dyson Purifier Cool
Gen 1 o cerca il tuo prodotto tra le migliori offerte di Trattamento Aria

Assembling your machine
Getting started
Place the remote control on top
of the machine with the buttons
facing down.
Plug in and switch on.
Information menuOscillation on/off
Airflow speed
Auto mode
Night mode
Standby on/off
Dyson Purifier Cool Gen1
Supplied with a combined glass HEPA+Carbon filter.
Shroud
Shroud release buttons
Standby on/off
Remote control
LCD screen
Amplifier loop
Filters (inside)
Use both hands to lift your machine out of the box, by its base.
Do not lift out by the loop amplifier.
An image of the air purifier fan with
the remote placed on the top of the
loop amplifier and the location of the
standby on/off button on the top of
the base of the machine.
The layout of the remote control with the power button on the top left, the
airflow speed toggle button in the middle left and the oscillation button on
the bottom left. On the top right-hand side is the Auto mode button, then
going downwards is the Night mode button and then the Information menu
button at the bottom.

Power and continuous monitoring
Stand-by on/off
Continuous monitoring
Press the Standby on/off button on your Dyson purifying fan or remote
control to stop your machine. It will continue to monitor the air quality.
Continuous monitoring is turned off by default. Once turned on,
it will always be active until you turn it off again.
With continuous monitoring turned on, your Dyson purifying fan will gather
particulate matter information, which is displayed on the LCD screen.
Continuous monitoring
Press and hold the Auto mode button on the remote control for 5 seconds
to turn it on. The LCD screen will indicate when continuous monitoring
is on or off.

Information menu
Filters
Particulate matter (PM10)
The remaining filter life is shown
on the LCD screen and will indicate
when your filters need replacing.
Larger microscopic particles up to 10 microns
in size, suspended in the air we breathe. These
include dust, mould and pollen.
Particulate matter (PM2.5)
Microscopic particles up to 2.5 microns in size,
suspended in the air we breathe. These include
smoke, bacteria and allergens.
Indoor particulate matter – 12 seconds
Monitors the current particulate matter with a
graph showing the last 12 seconds of data.
Press this button to scroll through the information being monitored by your
Dyson purifying fan.
Information about particulate matter and filter levels is shown on the
LCD screen.
When a particular type of pollutant causes air quality to decrease,
a symbol for the pollutant will show on the LCD screen.
The remote control with
the information button
on the bottom right.

Auto mode
Oscillation
Press the Oscillation button to circulate the air around the room and scroll
through the oscillation settings from 0°to 350°.
Airflow speed
Press the Airflow speed button to increase and decrease the airflow speed.
Set your Dyson purifying fan to Auto mode and the on-board sensors will
intelligently adjust the settings of the machine according to the air quality.
Air quality: your machine will pause when the target air quality has been
reached, switching on again when the air quality levels drop.
Airflow speed: the airflow speed will increase until the target air quality
has been reached.
In Night mode, your Dyson purifying fan will continue to monitor and
respond to changes, but only using its quietest settings – and with its
LCD screen dimmed.
Press the Night mode and Sleep timer button to scroll through the
timer options.
Night mode and Sleep timer
The remote control with
the oscillation button
on the bottom left.
The remote control
with the Airflow speed
toggle button on the
left hand side, in the
middle.
The remote control with
the Auto mode button
above the Night mode
button on the top right.
The remote control with
the Night mode and
Sleep timer button on
the right hand side,
in the middle, above
the Information menu
button.

Changing your HEPA+Carbon filter
Supplied with a HEPA+Carbon filter.
To change your HEPA+Carbon filter, push down on the buttons either side
of your machine to release the outer cover. Push down on the tabs to remove
the filter.
Push the replacement filter into the outer cover and make sure the tabs click
into place.
Put the outer covers into position on your machine and push firmly until they
both click securely into position.
Plug in and switch your machine, and reset your filter life.
Resetting your HEPA+Carbon filter life
Resetting your HEPA+Carbon filter life
It's important to reset your filter life after you have replaced your filter.
Press and hold the Night mode button on your remote control.
The display on your machine will countdown from five, the filter life will
be reset and your machine is ready to use.
Before changing your filter, switch off and unplug your Dyson purifying fan.
The remaining filter life is displayed on the screen and will indicate when
your non-washable filters need replacing. Press the Information button
on your remote.
You’ll need to reset the filter life on your machine.
Dyson Purifier Cool Gen1
5
sec
The air purifier fan with the filter covers open
showing a HEPA plus carbon filter located in the
filter covers. Arrows demonstrate that the filter
covers will need to be assembled onto the base
of the machine.
Pressing the Night mode
and Sleep timer button
on the middle right of the
remote control, above the
Information menu button
for 5 seconds.

Looking after your machine
Error codes
Cleaning your machine
To always get the best performance from your Dyson purifying fan,
it’s important to regularly clean it and check for blockages.
If your machine is dusty, wipe with a damp lint-free cloth.
Look for blockages in the air inlet holes on the filter and the small
aperture inside the loop amplifier.
Use a soft brush to remove dust and debris.
Don’t use detergents or polishes to clean your machine.
If your machine shows an error code, try turning it off and then on again.
If this doesn’t clear the error code contact Dyson Customer Care.
For more information and support for your machine go online:
www.dyson.com/support