E&G Classics 1091-018U-16 User manual

IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE !
Copyright © 2016 by E&G Corporation, LLC. All right reserved. The reproduction or uti li za tion of this work in any form or any elec tron ic, me chan i cal, or other means, no known or here af ter in vent ed,
including xe rog ra phy, pho to copy ing, and re cord ing, and in any in for ma tion storage retrieval system is for bid den with out written per mis sion of owners.
Notes to the Technician/Installer:
E&G is proud to present this package to you and reminds you that for technical in for ma tion, contact technical as-
sistance at 410-381-4900. Do not at tempt the in stal la tion of any E&G prod uct without first reading the detailed in -
struc tions. E&G will not war rant
dam aged parts or the ve hi cle due to altered in stal la tion procedures.
07/05/2016
2.
sing a small flat blade screwdriver, begin prying out the factory
chrome mouldings starting at the sides.
Copyright 2016 by E&G Corporation, LLC. Visit us online today at www.egclassics.com
2016 GMC Sierra SLT & SLE
3 Piece “Denali Style” Grilles
TOOLS RE UIRED
Automotive grade masking tape, plastic clip removal tool, electric drill, 9/64”, 5/32” and 1/16” drill bits, 1/4” nut
driver, flat blade screwdriver, glass cleaner and soft, clean cloths.
Upper Overlays - Will not fit base or factory Denali models
1. Apply masking tape to the painted filler between the grille and the
bumper to help protect the paint finish.
3. Continue to pull the mouldings off the factory grille. The mouldings
will either unclip or the mounting tabs will break off. These mould-
ings are not reused.
3
2
1
LT Part # 1091-018U-16 / LE Part #1091-058U-16
3
Important: If the factory grille on the vehicle you are working on does not have three chrome
rectangular openings, please call technical support at 410-381-4900 before proceeding.
4.
For “SLE” grilles only: se a 5/32” drill bit to enlarge the factory
mounting slots (where shown, each side) prior to E&G grille sec-
tion alignment.
4

6. Begin aligning the upper grille bottom section first. Align the center
two studs where the factory retaining clips are located. Insert a
small flat blade screwdriver to pry the tab away from the stud and
press in on the grille to begin seating the studs. Work from the cen-
ter out, alternating from bottom to top studs.
7. Continue aligning the studs with the retaining clips. Move the clips
as needed to press the grille tightly against the factory insert. Make
sure that once the upper grille bottom section is pressed into place
that it is perfectly centered inside the factory chrome surround.
Copyright 2016 by E&G Corporation, LLC. Visit us online today at www.egclassics.com
8. Install the upper grille center section using the same procedure out-
lined in Steps 6 and 7. Make sure that the edges of the grille align
with one another. You can use a small secton of wood or plastic and
insert it into any of the grille openings and tap the wood or plastic
with a mallet to adjust the side to side gap (alignment).
5. Paint all of the lower studs on all three grille sections with black
paint to help conceal them once the grille sections are installed.
6
5
9. Install the upper grille top section using the same procedure out
lined in Steps 6 and 7.
9
7
8
10. Once properly aligned with the factoy grille surround, use a 1/16”
drill bit to drill through the six (6) mounting holes in the E&G
grilles. Drill through the center of the holes, do not allow the drill
bit to touch the E&G grille. Apply a rust preventing sealer to the
hole in the grille as a precautionary measure against rust.
10

11. Install the supplied #6 x 3/4” Torx pin head screws to secure the
outer edges of the E&G grilles and finish the installation. Do not
overtighten or you could indent the grilles at the screw locations
or strip out the holes in the factory plastic grille.
Copyright 2016 by E&G Corporation, LLC. Visit us online today at www.egclassics.com
11
Quantity: Description: Part Number:
1 LT Denali tyle Upper Top Grille Overlay 1091-018A-16
1 LT Denali tyle Upper Center Grille Overlay 1091-018B-16
1
LT Denali tyle Upper Bottom Grille Overlay
1091-018C-16
1 Installation Hardware Kit 1091-0182-16
1 Torx T-10 Pin Head Tool 1999-0107-00
6 #6 x 3/4” Torx Pin Head crews 1999-0108-00
LT Upper 3 Piece “Denali” tyle Grille Part #1091-0185U-16
Quantity: Description: Part Number:
1 LE Denali tyle Upper Top Grille Overlay 1091-058A-16
1 LE Denali tyle Upper Center Grille Overlay 1091-058B-16
1
LE Denali tyle Upper Bottom Grille Overlay
1091-058C-16
1 Installation Hardware Kit 1091-0182-16
1 Torx T-10 Pin Head Tool 1999-0107-00
6 #6 x 3/4” Torx Pin Head crews 1999-0108-00
LE Upper 3 Piece “Denali” tyle Grille Part #1091-0585U-16
E&G Warranty Infor ation:
E&G Corporation, LLC. warrants its parts and products to be free from defects
in ma te ri al, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G. This warranty is limited
to the repair or replacement, at E&G’s option, of the defective part or product. Full E&G warranty information is avail-
able online @ www.egclassics.com.
E&G Product Returns:
Please contact the authorized E&G Dealer where you purchased our product
from in regards to any workmanship or warranty claims. All items returned to E&G must have a return authori-
zation number issued by us for inspection or a defective product and or warranty issue. All merchandise sent
back to E&G without proper paperwork or authorization will be rejected and returned.
SLT shown, SLE si ilar.