Front Runner SSDR005 User manual

SSDR005_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
Universal Drawer
Medium SUV
SSDR005
ENG
1
Thank you for purchasing Front Runner Universal Drawers System.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

SSDR005_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
10MM 10MM
1 1 X Universal Drawer Medium SUV
2 X Set Of Keys
2 6 X Eye Nut
3 6 X M8 Nylon Washer
4 6 X Stud Plate
5 4 X Carabiner Hook 60mm
6 4 X M6 Wing Nut
7 4 X Turnbuckle
8 4 X M6 x 20 Hex Bolt
9 8 X M6 x 19 x 1SS Flat Washer
10 8 X M8 D-Ring
11 4 X M6 Nyloc Nut
12 4 X M8 x 16 x 1.6 Flat Washer
13 4 X M8 x 16 Hex Bolt
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
17
1
4
3
2
5
6
7
8
9
11
10
9
6.5MM

SSDR005_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 3
FIT AND SECURE
2
2.1
2.2
2.3
Assemble each of the 4
turnbuckles (Item 7) with a wing nut
(Item 6) as shown. The wing nut will be
used to lock the Turnbuckles after they
have been set.
Place the Drawer System in the vehicle
and center it. Make sure the Turnbuckles
will be pulling outward to the existing
mounting points in the vehicle to prevent
it from moving after it has been secured.
If your vehicle does not have Tie-Down
points you can use the D-Rings (Item 10)
supplied.
Position the D-Rings so that the
Turnbuckles will pull outward to prevent
the Drawer System from moving after it
has been secured.
Mark the position of the D-Rings and drill
6.5mm holes.
Secure the D-Rings using M6 x 20 Hex
Bolts, M6 x 19 x 1SS Flat Washers and M6
Nyloc Nuts (Items 8, 9 & 11)
7
6
10MM
6.5MM
8
9
11
10
9

SSDR005_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 4
4
3
2
5
6
FIT AND SECURE
2
2.4
2.5
Connect the 60mm Laser Cut Carabiner
(Item 5) onto the D-rings on the drawers
upright.
Connect the Turnbuckles (Item 6) on the
other side of the 60mm Laser Cut Carabiner
and hook it into the existing tie-downs that
are fitted to the vehicle.
Secure the drawer by tensioning the
Turnbuckles until there is no more
movement on the drawer. Make sure the
drawer stays in position when doing this.
Lock the Turnbuckles with the wing nuts.
Do this by tightening the wing nuts up to
the turnbuckles.
Assemble the Eye-Nuts with a M6 Nylon
Washer and a Stud Plate
(Items 2, 3 & 4) and slide them into the
extrusion.

SSDS602_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 5
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
4
Now's the time to visit your favorite Front Runner Dealer in person or Online.
Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on: