Eastsign BU-650II.PLUS User manual

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Laminator
BU-650II.PLUS & BU-865II.PLUS
User Manual
Eastsign International Limited
Room 1818, 18/F., Shatin Galleria, 18-24 Shan Mei Street, Fotan, Shatin, N.T.,
Hong Kong
TEL: + 852 - 2117 0098
FAX: + 852 - 2117 0099
Website: www.eastsign.com
Email: [e-mail]

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
I. Introduction
BU-650II.PLUS & BU-865II.PLUS is developed for simple laminating machine
with auto-removing film and auto-receiving back paper, which is based on the
design of BU-650IIZ and deep understanding on the principle of lamination. It is
simple in structure, user-friendly and competitive in price.
This is working principle:
1) The motor drives to turn the up and bottom roller
2) Feeding roller and liner collecting roller is driven by up and bottom roller. It
saves manpower and is easy to operate.
Due to improved structure, it is more stable now and there is positive feedback
from distributors and end-users.
This machine is consisted of feeding roller, collecting roller and film guiding bar.
It can be used continuously or for a long period because of auto-peeling and
auto-collecting liner. So it is easy to use and work efficiently. This machine
works at low power consumption and variable speed.

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
II. Technical Specifications and Main Parameters
1
Machine Model
BU-650II.PLUS
BU-865II.PLUS
2
Maximal Laminating
Width
650mm
865mm
3
Laminating Speed
5m/min
5m/min
4
Maximum Diameter of
Collecting Media
150mm
150mm
5
Maximal Lifting Height
25mm
25mm
6
Roller Diameter
65mm
65mm
7
Supply Voltage
250V/10A
250V/10A
8
Main Motor
YN60-10 / i=50
YN60-10 / i=50
9
Machine size
760*280*500mm
975*280*500mm
10
Machine Weight
30 KG
40KG

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
III. Laminator’s structure name
Figure 1
1. Bottom Roller
2. Top Roller
3. Film Guiding Pole
Pole
4. Liner Collecting
Roller
5. Film Feeding Roller
6. Tension Knob for
Liner Collecting Roller
7. Tension Knob for
Film Feeding Roller
8. Handle for Lifting
Rollers
9. Control Panel
10. Front Working
Platform

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
IV. Operating Guide to Laminator
1. When laminating machine arrives in place, you should check if it is damaged
or not and there is any missing parts.
2. Before connecting to the main power, you should pay attention that the
power indicated on the laminating machine should be the same as the power
supply
3. Machine operating: first you should select the direction of roller rotation,
putting down the upper switch of selecting direction is positive turning, the
bottom switch is negative. Putting down the upper stopping switch is opening,
the bottom switch is stopping.
If you want to change the direction of roller turning, first you should stop the
machine, change the switch of selecting direction then you can start the
machine again. This avoids damaging the machine because of changing the
direction of the motor.
4. Adjusting the machine’s speed: counterclockwise rotate the switch of
adjusting speed is slowing down, clockwise rotation is increasing speed.
5. The sequence of cutting power is opposite to putting through the power.
6. All feeding and collecting roller can load and unload as a whole. There is
knob on one end of roller (Figure 1), which adjusts the friction to ensure that
the speed of receiving back paper is synchronized to the speed of laminating, to
ensure the quality of laminating. Clockwise rotating the handle is to increase
the damping, counterclockwise rotating reduces damping.
7. Both sides of the handle are for the rollers lifting. Rotating the handle in
clockwise direction descend the roller. Rotating the handle in counter-clockwise
lifts roller. If you rotate the roller clockwise, you will find the torque decreases
when the top roller comes into contact with the bottom roller. This is called
“space position”. The weight of the roller presses evenly on the bottom roller.
This time you can start lamination. When lifting the rollers, the handle of both
sides should rotate consistently to ensure the up roller level, or else it will
damage the parts.

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
Control Panel Power Supply and Switch
Figure2

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
V. Laminating Process
Figure 3

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
VI .Safety Precautions
1. Before using the machine, you should firstly read the machine’s manual to
comprehensively understand the main structure, performance and
technique. You should pay attention to all warning logo pasted on the
machine, to prevent accidents.
2. The power used by machine must be same as the power stated on the
nameplate and connected to earth.
3. The machine does not set optical protection switch. Operators in using the
machine should be carefully pay attention that don’t let your finger close
to the roller, to prevent your finger pressing.
4. If work is completed, you should raise the roller, to prevent the roller
deformation by pressing long time. At the same time, you should cut the
power supply.
5. Do not cut the film or picture on the roller to prevent scratching the roller
by sharp knives. After the roller is contaminated by glue, you can use
alcohol to clean the roller. It must not be organic solvents or water to
prevent the roller damaged and electrical short circuit.
6. The workplace should be dry and well ventilated, less dust, water.
Inflammable and explosive materials should not be stacked near the
equipment to prevent fire accidents.
7. Regular check on equipment and power cord.

Laminator BU-650II.PLUS & BU-865II.PLUS User Manual
Revised on Sep 16, 2013
Copyright © 2013 Eastsign International Limited
VII. Warranty
1. Customer should fill in the warranty form on our website.
http://eastsign.com/warranty_form.php
2. Warranty period is one year.
3. No free repair is available for damages caused by improper use.