Royal Sovereign RSH-380SL User manual

OWNER'S MANUAL
Desk Top RSH-380SL
Laminator
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal
SovereignInternational Inc.
www.royalsovereign.com

1
TABLE OF CONTENTS
TOPIC P AGE
1. Introduction ....................................................................................................................................... 2
2. Safety Precautions............................................................................................................................. 2
3. Included with Laminator..................................................................................................................... 3
4. Product Identification ......................................................................................................................... 3
5. Loading Film........................................................................................................................................4
6. Threading Film
6.1. Hot Film double-sided laminating .............................................................................................. 5-6
6.2. Hot Film single-sided laminating ............................................................................................. 7
7. Control of Roller Pressure ................................................................................................................ 8
8. Control Panel ....................................................................................................................................9
9. Laminating Steps
9.1. Hot Laminating.......................................................................................................................... 10
10. Using Cross Cutter......................................................................................................................... 11
11. Maintenance .................................................................................................................................. 11
12. Troubleshooting ............................................................................................................................. 12
13. Recommended Temperature and Speed Settings ....................................................................... 13
14. Specifications................................................................................................................................. 14
15. Warranty......................................................................................................................................... 15

2
Desk Top RSH-SERIES
1. INTRODUCTIONS
Thank you for choosing a Royal Sovereign laminator. It has been designed and
manufactured to provide years of continuous service. For complete operating and
maintenance information please read this manual thoroughly. Upon receipt of your
laminator, please inspect the box, the machine and all other contents for shipping
damage. Damage should be brought to the immediate attention of the delivering carrier
(See page 3 for list of shipment elements).
2. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points
that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/
or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should
make repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness
for the unit.
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot.
13. Do not place foreign objects inside the machine.
14. Do not cover the surface of the machine until the machine has completely cooled.

3
3. INCLUDED WITH LAMINATOR
PART NAME EA REMARK PART NAME EA REMARK PART NAME EA
REMARK
FUSE(65TS)
(AC250V 10A)
1
Power supply:
220V~240V
FUSE(65TS)
(AC250V 20A)
1
Power supply:
100V~110V
FUSE(65TS)
(AC250V 15A)
1
Power supply:
120V
4. PRODUCT IDENTIFICATION
* No. 11,12 are only designed for "S" model.
NO
PART NAME
NO
PART NAME
1
UPPER FILM
7
GUIDE-DOCUMENT
2
IDLE BAR
8
HANDLE-TENSION
3
HOT ROLLER
9
PRESSURE LEVER
4 SAFETY COVER 10 CONTROL PANEL
5 FRONT-TABLE 11 DECURLING BAR
6
LOWER FILM
12
IDLE BAR

4
5. LOADING FILM
Picture 1
Picture 2
Picture 3
Picture 4
1. As shown in picture 1, insert auto grips onto the upper/lower film shaft.
2. As shown in picture 2, using the special tool, fix the auto grips on the
film shaft with set-screws.
3. Set the glossy side of the upper and lower film towards the heat rollers.
( Glossy side is PET film and matte side is thermal polymer laminating
adhesive)
4. Center film as shown in picture 3 and 4.

5
6. THREADING FILM
6.1. HOT FILM DOUBLE SIDED LAMINA TING
UPPER ROLL FILM
ADHESIVE SIDE
IDLE BAR
LAMINATING HOTROLLERS
GLOSSY SIDE
PULL ROLLERS
ADHESIVE SIDE
LOWER ROLL FILM
IDLE BAR
GLOSSY SIDE
1. Turn the power switch on ("I" position). Power switch is located
in the rear of the unit on the left side.
2. Turn on the lower hot roller by pressing S/D
button on the control panel. This button will be lit
when the lower heat is on.
3. Complete the "Loading Film" steps as shown on
page 4.
4. Set the temperature and speed according to the
Recommended Temperature and Speed section.
5. Remove the Front Table.
6. Pull down the upper film over the Safety Cover to
the lower film; align and center the lower film to
upper film (Picture 1).
7. Rewind the upper film until the film aligns with the
Safety Cover.
8. Thread the film under the Upper Idle Bar and
underneath the Safety Cover until the film rests on
the upper roller (Picture 2).
Picture 1
Picture 2

6
Desk Top RSH-SERIES
8. Carefully pull up the laminate from the lower roll up
towards the first idle bar and then around the back
side of the second Idler (Caution: lower roller may
be hot).(Picture 3)
9. Tack the lower film to the upper film that is resting
on the main hot rollers (Picture 4).
10. Reinstall the Front Table and close the Safety
Cover.
11. Adjust the nip setting to 1/4'' (6mm).
12. Insert and push the leader board into the hot
rollers (Picture 5).
13. Adjust the nip setting to "Laminating" mode.
14. Push the Run button.
15. Press the Run button and adjust the supply roll
tension knobs by rotating clockwise or
counterclockwise. Turn it until the supply roll
films have some resistance (the tension
varies depending on the film thickness; the
thicker the film the more tension is required)
(Picture 6).
16. Press Stop button when the leader board has
completely exited the rear of the unit.
17. Use the Cross Cutter to cut the leader board from
the web (see page 18).
18. Peel Trim any excess film off of the leader board
edges. The leader board can be reused.
19. Set the roller nip setting to the appropriate position
for the lamination or encapsulation application.
Picture 3
Picture 4
Picture 5
Picture 6

7
6.2. HOT FILM SINGLE SIDED LAMINA TING
ROLL FILM
ADHESIVE SIDE
IDLE BAR
LAMINATING HOT ROLLERS
GLOSSY SIDE
PULL ROLLERS
IDLE BAR
SHAFT DE-CURLING BAR
1. Turn the power switch on("I" position). Power switch is located in the rear of the unit on the left side.
2. Follow the steps in the "Loading Film" procedure by loading the upper shaft with OPP Film.
3. Set the temperature and speed as shown as the recommended in page 13.
4. Center the OPP film.
5. Thread the film under the Upper Idle Bar and underneath the Safety Cover until the film rests on
the upper hot roller.
6. Pull a sheet of A3 paper into the laminating roller and pass under the idle-bar
and over the shaft-decurling bar. Make sure the idle-bar being in the lower location while laminating.
7. Link the paper to the film.
8. Adjust the nip setting to "Laminating" mode.
9. Press the run button and adjust the supply roll tension knobs by rotating clockwise or counterclockwise.
Turn it until the supply roll films have some resistance(the tension varies depending on the film thickness:
the thicker the film the more tensions is required) (Picture 6).
10.Stop the laminator when all of the laminated items have completely exited the
rear of the
machine.

8
3
7. CONTROL OF ROLLER PRESSURE
1
To set, pull the pressure lever outward and turn to one of the following positions.
1. OPEN: For detaching and cleaning rollers.
2. 6MM: For laminating 6mm[0.24in] thick board.
3. 5MM: For laminating 5mm[0.2in] thick board.
4. 3MM: For laminating 3mm[0.12in] thick board.
5. 1.5MM: For laminating 1.5mm[0.06in] thick board.
6. LAMINATING: For laminating 25~250micron(1~10mil) thick film.

9
8. CONTROL PANEL
LED Display
1. TEMPERATURE DISPLAY: Display current temperature.
2. SPEED DISPLAY: Display current Speed.
3. To change the roller’s temperature up or down.
150˚C
140˚C
1 130˚C 2
120˚C
110˚C
o o
(Range 110 C-150 C and 5 degree for a level.)
4. To change the speed of rollers. (Range 1-9)
5. REV: To reverse the rollers. Must press and hold the button to activate.
3
6. RUN /STOP: To start or stop the rollers from turning.
7. S/D: Single laminating/Double laminating.
NOTE: *1.Only one roller is heating while turning on the main power switch. Please press
the button “S/D” for two sides laminating and the LED-light is bright at once.
*2. STAND-BY MODE and AUTO POWER OFF MODE
STAND-BY MODE: If no activity is made within 30 minutes after each use the machine
will automatically switch into stand by mode (In stand-by mode the temperature will
decrease to 80~90 °C (176~194°F) and every other LED light of the temperature and
speed will be lit.
AUTO POWER OFF MODE: If the machine is in stand by mode and no activity is made
for 60 minutes the machine will automatically power off (Only the No.1 speed LED lights).
-If any activity is made while in stand by or auto power off mode the machine will return to
it’s previous stage.
4
5 6 7