EASY COOPS Chicken Coop Plan 8x24 User manual

8' x 24' Chicken Coop Plan
Up to 50 chickens

Compare Free vs. Premium plan
Free plan Premium edion
Pages
51
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
TRY PREMIUM
18

24'x8' chicken coop material list
Site Preparation
•Concrete
•Bricks
Bottom Frame
•Pressure-Treated Lumber
•Plywood
Walls Exterior Siding
•Pressure-Treated Lumber
•Wood siding boards
Walls Frames
•Pressure-Treated Lumber
Top Frame
•Pressure-Treated Lumber
Shed’s Roof
•Pressure-Treated Lumber
•Pressure-Treated Board
•Plywood
•Building paper
•Asphalt shingles
•Metal drip edge
Fasteners & Hardware
•Corner braces
•Galvanized nails
•Wood screws
Front/Side Shed's Window
•Pressure-Treated Lumber
•Window beading
•Glass

Framing the Coop's Floor
1.1 Assemble the frame using 1 1/2" x 7 1/4" pressure-treated lumber.
You will need eight boards cut to 7'-6 1/4" that will be the joist.
1.2 Secure the beams with 8x3" wood screws.
1.3 Using a speed square or carpenter's square, check the corners to make sure they are 90°.
STEP 1
1 1/2"7'-6 1/4"1 1/2"
1'-1 3/4"7 x 1'-2 1/2"11"

STEP 2
Assemble Side Wall Frames
2.1 Using 1 1/2" x 3 1/2", 1 1/2" x 5 1/2" and 3 1/2" x 3 1/2" pressure-treated lumber, construct right
side wall frame using the drawing below as a reference. For each wall you will need nine boards cut to
6'-11", four boards cut to 5'-1/2" and two boards cut to 3'-3" that will be studs, two boards cut to 11'-9
1/4" that will be top and bottom beams, four boards cut to 1'-11" that will be the window headers, two
boards cut to 1'-8" that will be rough sills and two boards cut to 1'-5" that will be cripple studs.
2.2 Connect the beams with 3" wood screws.
2.3 Using a speed square or carpenter's square, check the corners to make sure they are 90°.
1'-2 1/2" 1'- 1/4" 10 3/4" 10 3/4" 1'- 1/4" 1'- 1/4" 10 3/4" 10 3/4" 1'- 1/4" 1'-2 1/2"3 1/2" 3 1/2"
1 1/2"
6'-11"
1 1/2"
1'-11"
1'-8"
1'-8"
1'-5"
5 1/2"
5'- 1/2"
11'-9 1/4"
1'-5"
1'-11"
1'-8"
5'- 1/2"
1'-8"
3'-3" 3'-3"
5 1/2"

STEP 3
9" 1'- 1/4" 10 3/4" 10 3/4" 10 3/4" 1'- 1/4" 9"
Assemble Front and Back Wall Frames
3.1 Using 1 1/2" x 3 1/2" and 1 1/2" x 5 1/2" pressure-treated lumber, construct front wall frame using
the drawing below as a reference. You will need six boards cut to 6'-11" and two boards cut to 5'-10 1/2"
that will be studs, two boards cut to 2'-3 1/4" that will be the bottom beams, one board cut to 7'-2 1/4"
that will be the top beam, two boards cut to 2'-11" that will be the door header and two boards cut to 7"
that will be cripple studs.
3.2 Connect the beams with 2x3" wood screws.
3.3 Using a speed square or carpenter's square, check the corners to make sure they are 90°.
7'-2 1/4"
1 1/2"
6'-11"
1 1/2"
2'-3 1/4" 2'-8" 2'-3 1/4"
5'-10 1/2"
2'-11"
7"
5 1/2"

STEP 4
Assemble Aviary Side Wall Frames
4.1 Using 1 1/2" x 3 1/2" and 3 1/2" x 3 1/2" pressure-treated lumber, construct side wall frames for
aviary using the drawing below as a reference. For each side wall you will need four boards cut to 7'-5"
that will be the studs and two boards cut to 12'-1 1/4" that will be the top and bottom beams.
4.2 Connect the beams with 2x3" wood screws. To connect top beams to the coop's frame use 3" x 3"
corner braces.
4.3 Using a speed square or carpenter's square, check the corners to make sure they are 90°.
2'-10 1/2" 2'-8 3/4" 2'-8 3/4" 2'-7"
12'-1 1/4"
7'-5"

STEP 5
1'-6 3/4" 1' 1' 1'
3'
3'-3"
1'-1"
5 1/2"
1'-6 3/4"
Assemble Aviary Front Wall Frame
5.1 Using 1 1/2" x 3 1/2", 1 1/2" x 5 1/2" and 3 1/2" x 3 1/2" pressure-treated lumber, construct aviary
front wall frame using the drawing below as a reference. You will need four boards cut to 7'-5" and two
boards cut to 5'-10 1/2" that will be studs, two boards cut to 7'-2 1/4" that will be top and boom beams,
two boards cut to 3'-3" that will be the door header and two boards cut to 1'-1" that will be cripple studs.
5.2 Connect the beams with 2x3" wood screws.
5.3 Using a speed square or carpenter's square, check the corners to make sure they are 90°.
7'-2 1/4"
5'-10 1/2"
7'-5"

STEP 6
Assemble the Roof Frame
6.1 Using 1 1/2" x 5 1/2" pressure-treated lumber, cut thirty eight rafters 5'-5 3/4" long according to the
dimensions in drawings below.
6.2 Using 1 1/2" x 3 1/2" pressure-treated lumber, cut sixteen collar ties 5' long according to the
dimensions in drawings below.
6.3 Using 1 1/2" x 5 1/2" pressure-treated board, cut one board 10 1/4" long, one board 1'-3 3/4" long
and sixteen boards cut to 1'-2 1/2" long that will be ridge boards according the illustration below.
6.4 Connect the beams with 3" and 5" wood screws.
10 1/4"16 x 1'-2 1/2"1'-3 3/4"
5'-5 3/4"

STEP 7
Install Building Paper
7.1 Cover the walls with building paper. You will need 295 sq ft.

STEP 8
Coop's Roof Sheathing Installation
8.1 You will need 285 Sq Ft of building paper and asphalt shingle roofing.
8.2 Cover the plywood and drip edge with building paper. Try to install sheets with 1" overlapping.
Use 2" nails to secure the sheets.
8.3 Install asphalt shingle roofing using an industrial stapler.
Shingles layer
Building paper layer
5'-9 3/4"
24'-5 1/2"

STEP 9
Assemble and Install Front and Back Doors
9.1 Build the door frame using 3/4" x 3 1/2" pressure-treated lumber.
You will need two boards cut to 5'-11 1/2" that will be the vercal girts, two boards cut to 2'-1/2" that will
be the horizontal girts and one board cut to 5'-9" that will be cross brace.
9.2 Prepare the 5/8" plywood sheet with dimensions 2'-7 1/2" x 5'-11 1/2" for the door according to the
drawing.
9.3 Use 3/4" x 2 1/2" pressure-treated lumber for the door trim and fasten with 2" wood screws.
You will need two boards cut to 2'-2 1/2" and two boards cut to 5'-11 1/2".
9.4 Using 1/4" x 3/4" pressure-treated lumber, cut and install a starter course 2'-2 1/2" long using node E
on page 32 as a reference.
9.5 For the exterior siding on the door, use 1/2" x 6" wood siding boards and the illustration below as a
reference. Assemble siding shields with 2" galvanized nails.
9.6 Install three 3" door hinges using 6x1" wood screws.
Finish the door installaon by aaching 6" door pull and 3" surface bolt (see nodes G, H).
Front wall ( 1 : 35 )
G ( 1 : 8 )
H ( 1 : 8 )

STEP 10
Assemble and Install Windows
You will need to assemble four windows
10.1 Using 1 1/2" x 1 1/2" pressure-treated lumber, assemble the outer frame for the window as shown in
the drawing below. You will need four boards cut to 1'-7 1/2" that will be the vercal and horizontal girts.
Cut the recesses in each beam for splicing connection and mill a recess for the glass.
10.2 Prepare and install 1'-5 1/4" x 1'-5 1/4" glass into inner frame groove and fasten it by window
beading from four sides. Use 1/2" galvanized nails.
10.3 Insert window into wall openings and connect them with 3" wood screws to the wall beams.

STEP 11
Assemble The Nesting Boxes
You will need to assemble two nesting boxes.
11.1 Cut 5/8" plywood for the box according to the drawing.
You will need to cut one 10" x 6'-8 3/4" sheet for the top plane, one 1'-8" x 6'-8 3/4" sheet for the boom
plane, one 2'-6" x 6'-8 3/4" sheet for the back wall and six 1'-8" x 2'-4 3/4" sheets for the side and inner
partitions.
11.2 Use 1 1/2" x 3 1/2" pressure-treated material for building the nesting box frame and secure with 3"
and 5" wood screws. You will need two boards cut to 3'-1 1/2", two boards cut to 2'-3 1/2", two boards
cut to 1'-1" and two boards cut to 6'-8 3/4".
11.3 Provide and install nest's roost from the pressure-treated lumber with cross section 3/4" x 1 1/2".
You will need ten boards to 2'-2" and two boards cut to 6'-7 1/2".
6'-11 3/4"
3'-1 1/2"

STEP 12
Assemble The Roost
You will need to assemble two roosts.
12.1 Assemble the roost using 1 1/2" x 2 1/2" pressure-treated material.
You will need two boards cut to 4' and two boards cut to 3'-1".
12.2 Connect the beams with 3" wood screws.
12.3 Install the roost to the walls with the help of 3" screws. Using 1 1/2" x 2 1/2" pressure-treated
material prepare one support stud 4' long and connect it to the corner of the roost according to the
drawing below.
4
'
4
'

Assemble and Install Door Ramp
You will need to prepare two ramps: for the front and back doors.
13.1 Using 3/4" x 3 1/2", 3/4" x 5 1/2", 1 1/2" x 3 1/2" and 1 1/2" x 7 1/4" pressure-treated lumber,
construct door ramp using the drawing below as a reference. You will need three boards cut to 2'-9 1/2"
that will be support girts, two boards cut to 1'-2 1/2" that will be joists (cut the top edge to t the angle of
support girts), one board cut to 5" x 2'-9 1/2" that will be rim joist and ten boards cut to 2'-9 1/2" that will
be top sheathing.
13.2 Assemble siding shields with 2" and 3" galvanized nails.
STEP 13
2'-9 1/2"
2
'-1
1
"

STEP 14
Final Touches
Now that your chicken coop is all done, you are ready to decorate it any way you want using your
favorite paint, stain, or preservative.

Compare Free vs. Premium plan
Free plan Premium edion
Pages
51
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
 0 0
TRY PREMIUM
18

Copyright
The text and illustrations that appear here are the exclusive property of shedplans.org and are
protected by federal copyright laws. The duplication, sale or distribution of any portion of these
plans without prior written consent from the original designer will be subject to the appropriate
penalties for copyright infringement. Sharing this plan on the web is only permited with
an indicated original source: https://easycoops.com/
For more great HOW-TO plans please visit: https://easycoops.com/