Eaton SPDV60-300 User manual

Specification are subject to change without notice. Copyright 2007 Eaton Power Quality Pty Ltd
Technical Specification –SPDV60-300 Tvss Doc# 510083
Page 1 of 2
Web: http://www.powerware.com.au Phone: 1300 UPS UPS
SPDV60-300 SURGE DIVERTER
(Single mode, 220-250V (380-440V), 60/30kA)
INSTALLATION INSTRUCTIONS
FEATURES
• 1 mode plug-in protection (L-N)
• Compact solution for primary protection
• DIN43880 base, 35 mm DIN-rail mountable
• MOV is thermally protected
• Includes dry-contact alarm
Applications
• Mains point-of-entry /Main SWB
• Telecommunication Systems / Rectifiers
• Process and Control Systems / Factories & Units
• Computer Systems / Medical Systems
• All sensitive Electronic Equipment
FUNCTIONAL DESCRIPTION
The SPDV60-300 is designed to protect single and 3-
phase power systems against damage from surges
and spikes caused by lightning and other electrical
sources. The unit is intended for point-of-entry or
sub-board protection and is connected in parallel with
the power system via HRC fuses. The unit features a
plug-in module that may be replaced without rewiring
in the event of a fault. Check that the model you have
purchased is rated correctly for your power system.
.
This model (SPDV60-300) is designed for single
and 3-phase power systems, with a grounded
neutral, in the range of 220-250V(380-440V). If
your power system is “delta” (i.e. ungrounded),
or a different voltage, this model is NOT suitable.
Please contact your supplier for a suitable model to
suit your application.
OPERATION
The operational status of the unit is shown by a flag
indicator on the front of the module. In normal
operation, the flag is green. If the unit becaomes
damaged, the flag changes to red, indicating that
replacement is necessary. A ‘dry-contact’ alarm
output is fitted to the base unit and will change over if
the module is faulty or not in place.
WARRANTY
Eaton Power Quality warrants this unit against faulty
parts and workmanship for a period of 12 months
from the date of purchase. If this product fails to
operate correctly, please contact your Eaton
representative. This warranty doesn’t cover neglect
or intentional misuse. As this product is intended for
use in electrically harsh environments no claim is
made of suitability for purpose. This unit is designed
to reduce the likelihood of damage, not prevent it.
Please also note that an excessive surge, such as
from a direct lightning strike to the site or a power
system fault, may cause damage to the unit and
render it inoperable. A unit that has been damaged in
this way is not warrantable.
For installation details,
see over page.
SPECIFICATIONS
Manufacturers name and model Eaton Powerware
SPDV60-300
Method of mounting Fixed. DIN Rail mount
Input voltage 220-250VAC (380-440V)
40-70Hz
Maximum continuous operating
voltage - MCOV 300VAC
Service type TN-C and TN C-S (3-phase
with grounded neutral)
Test classification Class II
Supply current <10mA
Initial clamp voltage 470V
Maximum rated surge current -
Ismax 8/20us 60kA
Nominal surge current - In
8/20us 30kA
Residual voltage (Vpl) @
3kA, 8/20uS 1.0kV
Residual voltage (Vpl) @ Ismax
30kA, 8/20uS 1.4kV
Energy absorbtion (2ms) 2130j
Nominal surge lifetime (In) 30kA (8/20uS), 20 times
Internal protection MOV thermal disconnect
device
External disconnector
requirements Gg/Gl HRC fuses, 1 per unit/phase, 160A maximum.
Terminations Power terminals 25mm2,
Alarm terminals 1.5mm2
Alarms/indicators Flag indicator, dry contact
alarm relay –
250VAC/24VDC, 2A
Location Category Indoor
Enclosure rating IP20
Applicable standards. IEC61643-1, IEC610006,
ANSI/IEEE C62.41,
AS1768-1991, AS3100
Dimensions DIN43880, 1 units (17mm)
Weight 100g
Environment -10 to 60C, 0-90%RH
Warranty 12 months, workmanship
and materials

Specification are subject to change without notice. Copyright 2007 Eaton Power Quality Pty Ltd
Technical Specification –SPDV60-300 Tvss Doc# 510083
Page 2 of 2
Web: http://www.powerware.com.au Phone: 1300 UPS UPS
INSTALLATION
Refer to the procedure and diagram shown to connect the
SPDV60-300.
PROCEDURE:
1. CHECK
• Always work safely – disconnect power before
making connections.
• All wiring must be carried out by suitably qualified
personnel according to the applicable standards.
• Check for correct operating voltage and power
system. This model (SPDV60-300) is designed for
power systems in the range of 220-250V(380-
440V). If your power system is “delta” (i.e.
ungrounded), or a different voltage, this model
is not suitable. Please contact your supplier.
• ** For installation adjacent to an M.E.N. link, use
as shown.
• ** For installations remote from the M.E.N., a
separate N-E protector is required (SPD50Ngi).
• Always use the correct size HRC fuses.
• For services >160A, use 160A fuses. For services
<160A, no fuse is necessary however an SPD
fault may cause a loss of power to the site.
• Always use Gg or Gl-rated fuses. Do not use
delay types or ‘semiconductor’ fuses.
• For 80A domestic supplies, no fuse is necessary.
2. INSTALL
• Locate a fuse position as close as possible to the
Main Switch.
• Install fuseholders or fuse-switch.
• Locate a suitable position for the SPD, ensuring
adequate space for cables. Do not install above
heat-generating objects or in any position that is
exposed to weather.
• Install unit to DIN-rail in switchboard or cabinet.
3. CONNECT
• Connect wiring - refer to connection diagrams. If
using stranded cable, always use wire ferrules for
lowest resistance and to prevent damage to the
wire.
• Use a suitably-rated cable for power connections.
Cable should be rated for operation at the system
voltage and should be 6mm2to 25mm2.
• Use short cables for all connections or protection
will be reduced.
• Use a suitably-rated cable for alarm connections.
Cable should be rated for operation at the system
voltage and should be 0.5mm2to 1.5mm2.
4. NOTES:
• 160A fuses are rated such for maximum surge
rating. On services below 160A, high-level surges
may cause disconnection of the supply.
• Wiring from fuse to SPD is carrying surge currents
only, not load current. This means that smaller
cables may be used than is normal for the current
rating.
• If using under-sized cables, some energy
authorities require double insulation (i.e. sleeving)
of the cables.
• Maximum alarm relay resistive load is 2A.
• Unplug the alarm connector for termination.
• It is recommended not to connect the alarm
contacts to AC mains circuits if possible, to
prevent flashover from surges on the AC line.
Connect to a PLC or BMS if available.
• Do not Megger test cabling with unit connected –
unit may be damaged.
EARTHING
For proper operation, all surge diverters rely upon a good
earth connection:
• The main earth wire (from earth link on switchboard to
ground rod or system) MUST be as short and direct as
possible. Extra cable must not be looped.
• Earth connections from the unit to neutral or earth link
MUST be as short as possible.
Failure to consider the above points can result in
improper operation of the unit and possible damage to
the installation.