Eaton Eaton 5PX Assembly instructions

Eaton 5PX
Advanced User Guide
Copyright © 2021 EATON
All rights reserved.
614-40094-00
5PX1000IRT2UG2
5PX1500IRT2UG2
5PX2200IRT2UG2
5PX2200IRT3UG2
5PX3000IRT2UG2
5PX3000IRT3UG2
5PXEBM48RT2UG2
5PXEBM72RT2UG2
5PXEBM72RT3UG2

614-40094-00
2
Special symbols
The following are examples of symbols used on the UPS or accessories to alert you to importantinformation:
DANGER: Dangerous voltage levels are present within the UPS. The UPS has its own internal power
source (the battery). Consequently, the power outlets may be energized even if the UPS is
disconnected from the AC power source.
Important instructions that must always be followed.
CAUTION: Batteries present a risk of energy or electrical shock or burn from high short circuit current.
Observe proper precaution. Batteries may contain HIGH VOLTAGE and CORROSIVE, TOXIC and
EXPLOSIVE substances.
Information, advice, help.
Read the documentation provided.
Disconnect input plug.
Before maintenance, first shut down the UPS then disconnect the AC power source, internal and
external batteries then discharge capacitors by pressing the ON button and wait 5 minutes.
This equipment should only be used in a dry indoor environment.
Operating range of temperature.
Operating range of humidity.
The UPS and their batteries must be kept in a ventilated place.

614-40094-00
3
Table of Contents
1 Introduction ................................................................................................................... 5
1.1 Environmental protection .................................................................................................................... 5
1.2 Benefits.................................................................................................................................................. 6
2 Presentation................................................................................................................... 7
2.1 Standard installation ............................................................................................................................ 7
2.2 Rear panel.............................................................................................................................................. 8
2.3 Optional accessories............................................................................................................................. 9
3 Installation ..................................................................................................................... 9
3.1 Inspecting the equipment .................................................................................................................... 9
3.2 Recommended positions.................................................................................................................... 11
3.3 EBM connection .................................................................................................................................. 12
3.4 UPS connection................................................................................................................................... 14
3.5 Connection with a FlexPDU (Power Distribution Unit) optional module......................................... 14
3.6 Connection with a HotSwap MBP (Maintenance ByPass) optional module .................................... 14
4 Interfaces and communication ................................................................................... 16
4.1 Control panel....................................................................................................................................... 16
4.2 LCD description................................................................................................................................... 17
4.3 Display functions................................................................................................................................. 18
4.4 User settings........................................................................................................................................ 20
4.5 Communication ports......................................................................................................................... 23
4.6 UPS remote control functions............................................................................................................ 25
4.7 Eaton Intelligent Power Software suite ............................................................................................. 28
4.8 Cybersecurity ...................................................................................................................................... 28
5 Operation ..................................................................................................................... 28
5.1 Start-up and normal operation .......................................................................................................... 28
5.2 Starting the UPS on battery................................................................................................................ 29
5.3 UPS shutdown..................................................................................................................................... 29
5.4 Operating modes ................................................................................................................................ 29
5.5 Return of AC input power ................................................................................................................... 30
5.6 Retrieving the event log...................................................................................................................... 30
5.7 Retrieving the fault log ....................................................................................................................... 30

614-40094-00
4
6 UPS maintenance......................................................................................................... 30
6.1 Equipment care................................................................................................................................... 30
6.2 Storing the equipment........................................................................................................................ 30
6.3 When to replace batteries................................................................................................................... 31
6.4 Replacing batteries ............................................................................................................................. 31
6.5 Replacing the UPS equipped with a HotSwap MBP .......................................................................... 33
6.6 Recycling the used equipment........................................................................................................... 33
7 Troubleshooting........................................................................................................... 33
7.1 Typical alarms and faults.................................................................................................................... 34
7.2 Silencing the alarm ............................................................................................................................. 36
7.3 Service and support ............................................................................................................................ 36
8 Specification and technical characteristics................................................................ 36
8.1 UPS model list ..................................................................................................................................... 37
8.2 Extended Battery Module model list.................................................................................................. 37
8.3 Electrical input .................................................................................................................................... 37
8.4 Electrical input connections............................................................................................................... 38
8.5 Electrical output.................................................................................................................................. 38
8.6 Electrical output connection.............................................................................................................. 39
8.7 Battery ................................................................................................................................................. 39
8.8 Environmental and safety .................................................................................................................. 40
9 Glossary ........................................................................................................................ 40

614-40094-00
5
•
•
•
Materials Abbreviations Number in the symbols
Polyethylene terephthalate PET 01
High-density polyethylene HDPE 02
Polyvinyl chloride PVC 03
Low-density polyethylene LDPE 04
Polypropylene PP 05
Polystyrene PS 06
1 Introduction
Thank you for selecting an Eaton 5PXproduct to protect your electrical equipment.
TheEaton 5PXrange has been designed with the utmost care. We recommend that you take the time to read this
advanced user guide to take full advantage of the many features of your UPS (Uninterruptible Power System).
Before installing yourEaton5PX,please read the information and safety instructions provided. Follow the instructions in
the quick start guide and if necessary, refer to this advance user guide.
To discover the entire range ofEatonproducts, we invite you to visit ourweb siteateaton.comor
contactyourEatonlocal representative.This UPS can be used in IT power system. This UPS complies with the IP20
protection type.
1.1 Environmental protection
Eatonhas implemented an environmental-protection policy. Products are developed according to an eco-design
approach.
Substances
This product does not contain CFC and HCFC. This product does not contain asbestos. This product is compliant with
regulations on the restriction of the use of substances in electrical and electronic equipment.
Packaging
To improve waste treatment and facilitate recycling, separate the various packing components.
The cardboard we use comprises over 50% of recycled cardboard.
Plastic bags are made of polyethylene.
Packing materials are recyclable and bear the appropriate identification symbol.
Follow all local regulations for the disposal of packing materials.
End of life
Eatonwill process products at the end of their service life in compliance with local regulations. Eatonworks with
companies in charge of collecting and eliminating our products at the end of their service life.
Product
The product is made up of recyclable materials. Dismantling and destruction must take place in compliance with all local
regulations concerning waste. At the end of its service life, the product must be transported to a processing center for
electrical and electronic waste.eaton.com/recycling

614-40094-00
6
Battery
The product contains lead-acid batteries that must be processed according to applicable local regulations concerning
batteries. The battery may be removed to comply with regulations and in view of correct disposal.
1.2 Benefits
The Eaton 5PXuninterruptible power system (UPS) protects your sensitive electronic equipment from themost common
power problems, including power outages, voltagesags, impulsive transients, line noise, and long-term under and over
voltage conditions.
Power outages can occur when you least expect it and power quality can be erratic. These power problemshave the
potential to corrupt critical data, destroy unsaved work sessions, and damage hardware - causinghours of lost
productivity and expensive repairs.
With the Eaton 5PX, you can safely eliminate the effects of power disturbances and guard the integrityof your
equipment. Providing outstanding performance and reliability, the Eaton 5PX’s unique benefitsinclude:
• ABM® technology that uses advanced battery management to increase battery service life, optimize recharge time, and
provide a warning before the end of useful battery life
• Standard communication options:one RS-232 communication port, one USB communication port, relay output
contacts
• Optional connectivity cards with enhanced communication capabilities
• Extended runtime with up to four Extended Battery Modules (EBMs) per UPS
• Remote On/Off control
• Backed by worldwide agency approvals
• Remote firmware upgrade capability.

614-40094-00
7
2 Presentation
2.1 Standard installation
Tower installation Rack installation
Weights and dimensions
Description (UPS) Weights (lb / kg) Dimentions (inch / mm) D x W x H
5PX1000IRT2UG2 43.2 / 19,6 17.6x17.2x3.4 / 448x438x85,5
5PX1500IRT2UG2 49.4 / 22,4 17.6x17.2x3.4 / 448x438x85,5
5PX2200IRT2UG2 62.2 / 28,2 23.7x17.2x3.4 / 603x438x85,5
5PX2200IRT3UG2 60.6 / 27,5 19x17.2x5.1 / 483x438x129
5PX3000IRT2UG2 69.9 / 31,7 23.7x17.2x3.4 / 603x438x85,5
5PX3000IRT3UG2 68.6 / 31,1 19x17.2x5.1 / 483x438x129
Description (EBM) Weights (lb / kg) Dimentions (inch / mm) D x W x H
5PXEBM48RT2UG2 61.3 / 27,8 17.6x17.2x3.4 / 448x438x85,5
5PXEBM72RT2UG2 89.1 / 40,4 23.7x17.2x3.4 / 603x438x85,5
5PXEBM72RT3UG2 87.5 / 39,7 19x17.2x5.1 / 483x438x129

614-40094-00
8
2.2 Rear panel
5PX1000IRT2UG2 - 5PX1500IRT2UG2
5PX2200IRT2UG2 - 5PX3000IRT2UG2
5PX2200IRT3UG2 - 5PX3000IRT3UG2
5PXEBM48RT2UG2 - 5PXEBM72RT2UG2
5PXEBM72RT3UG2
①UPS
② Input AC power source
③Primary group (critical equipment)
④Outlet group (programmable outlets)
⑤USB communication port
⑥RS232 communication port
⑦Relay output contact
⑧Connector for ROO (Remote On/Off) control and RPO
(Remote Power Off)
⑨Slot for optional communication card
⑩Connector for additional External Battery Module
⑪Connector for automatic recognition of an additional
battery module
⑫Ground screw

614-40094-00
9
1.
2.
2.3 Optional accessories
Part number Description
5PXEBM48RT2UG2
5PXEBM72RT2UG2
5PXEBM72RT3UG2
Extended Battery Module
Network-M2 Eaton Gigabit Network Card (SNMP v1/v3 and IP v4/v6 // Ethernet 10/100/1000BaseT)
INDGW-M2 Eaton Industrial Gateway Card (Modbus TCP / RTU)
Relay-MS Eaton Relay card (1 x RS232 or 5 x Relay output)
INDRELAY-MS Eaton Industrial relay card (5x relay outputs with dry contacts for remote alarm information)
EMPDT1H1C2
Environmental Monitoring Probe Gen2
Compatibility : Gigabit Network Card (Network-M2) / Industrial Gateway Card (INDGW-M2) / Eaton
ePDU G3/G3+
MBP3KIF
MBP3KID
MBP3KI
HotSwap external maintenance bypass 4 FR
HotSwap external maintenance bypass 4 DIN
HotSwap external maintenance bypass 6 IEC
EFLX8F
EFLX8D
EFLX12I
FlexPDU 8 FR
FlexPDU 8 DIN
FlexPDU 8 IEC
3 Installation
3.1 Inspecting the equipment
If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or
place of purchase and file a claim for shipping damage. If you discover damage after acceptance, file a claim for
concealed damage.
To file a claim for shipping damage or concealed damage:
File with the carrier within 15 days of receipt of the equipment;
Send a copy of the damage claim within 15 days to your service representative.
Check the battery recharge date on the shipping carton label. If the date has passed and the batteries were never
recharged, do not use the UPS. Contact your service representative.

614-40094-00
10
Package content
Verify that the following additional items are included
with the UPS:
①UPS
⑬Connection cable to AC power source (2200VA &
3000VA models only)
⑭Connection cables for the protected equipment
⑮RS232 communication cable
⑯USB communication cable
⑰Safety instructions
⑱Quick start
⑲Cable locking systems
⑳Rack kit for 19-inch 4-post enclosures
㉑Two supports for tower position (tower feet)
㉒Communication card (optional)
㉓ FlexPDU module(optional)
㉔ Connection cables between FlexPDU module and UPS(
optional)
㉕HotSwap MBP module (optional)
㉖Connection cables between HotSwap MBP module
and UPS (optional)

614-40094-00
11
3.2 Recommended positions
Installation in tower position
If you ordered other UPS accessories, refer to specific user manuals to check the tower installation with the UPS.
To install the UPS:
Place the UPS on a flat, stable surface in its final location.Always keep 6" or 150 mm of free space behind the UPS rear
panel for ventilation.
If installing additional EBM, place them next to the UPS in their final location.
Follow steps 1 to 5 to adjust the orientation of the LCD panel and of the logo.

614-40094-00
12
Installation in rack position
Follow steps 1 to 4 for module mounting on the rails.
The rails and necessary hardware are supplied by Eaton.
3.3 EBM connection
Tour installation
A small amount of arcing may occur when
connecting an EBM to the UPS. This is normal and will
not harm personnel. Insert the EBM cable into the UPS
battery connector quickly and firmly.
1.Attach the UPS and the EBMs to each other using the
supplied mounting plate. Up to 4 EBMs may be
connected to the UPS.
2. Connect the EBMs power cable and the attached
battery detection cable as shown in the picture.
3. Verify that the EBM connections are tight and that
adequate bend radius and strain relief exist for each
cable.

614-40094-00
13
Rack installation
A small amount of arcing may occur when
connecting an EBM to the UPS. This is normal and will
not harm personnel. Insert the EBM cable into the UPS
battery connector quickly and firmly.
To increase stability, it is preferable to place the
EBM below the UPS.
1. Fix the rail on the back of the rack.
2. Fix the rail on the front of the rack using the two holes
at the bottom.
3. Fix the ears plate to the UPS.
4. Place the UPS on the rails and fix the ears plate to the
top hole of the rail.
5. Connect the EBM power cable as shown in the picture.
6. Connect the RJ45 battery detection cable of the first
EBM between the EBM and the UPS connector "Batt
detection" (11). For any additional EBM, connect the
battery detection cable to the previous EBM.
Verify that the EBM connections are tight and that
adequate bend radius and strain relief exist for each
cable.

614-40094-00
14
3.4 UPS connection
Check that the indications on the name plate located on the back of the UPS correspond to the AC-power source
and the true electrical consumption of the total load.
1.For the 5PX 1000 / 1500, connect the UPS input socket
(2) to the AC power source using the cable of the
protected equipment.
For the 5PX2200/ 3000, connect the UPS input socket (2)
to the AC-power source using the cable (13) supplied.
2.Connect the loads to the UPSusing the cables (14).It is
preferable to connect thepriority loads to the
outletsmarked (3) and the non-priorityloads to the
outlets Group1, Group2 (4) that can be programmed.
For the 5PX2200/ 3000 models, connect any high-power
devicesor matching Power Distribution Unit (PDU) to
the16Aoutlet.
Fit the connection securingsystem that prevents the
plugsfrom being pulled outaccidentally.
3.To program shutdown and startup of the Group1 and
Group2 outlets in order to extend battery runtime and
perform scheduled shutdowns, please see the "In/Out
settings" section.
3.5 Connection with a FlexPDU (Power Distribution Unit) optional module
1.5PX 1000 / 1500 : Use the power cable of the protected
equipment.
5PX2200/ 3000 connect the UPS input socket to the AC
power source using the cable (13) supplied.
2.Connect the input socket on the FlexPDU module (40)
to the UPS outlet (3) using the cable (24) supplied. The
cable and the connectorsare marked in red.
3.Connect the equipment to the outlets (41) on the
FlexPDU module. These outlets differ, depending on the
version of the FlexPDU module.
4. Fit the connection securingsystem that prevents the
plugsfrom being pulled outaccidentally.
3.6 Connection with a HotSwap MBP (Maintenance ByPass) optional module
The HotSwap MBP module makes it possible to service or even replace the UPS without affecting the connectedloads
(HotSwap function).

614-40094-00
15
1.Connect the input socket (48) onthe HotSwap MBP
module to theAC power source using the cable(13)
supplied.
2.Connect the UPS input socket (2)to the “UPS
Input” (47) on theHotSwap MBP module, using thecable
(26) supplied. This cableand the connector are
markedblue.
3.Connect the UPS outlet (3) to the “UPS Output” (46)
on the HotSwap MBP module, using the cable (26)
supplied. This cable and the connector are marked in
red.
4. Connect the equipment to the outlets(42) on the
HotSwapMBP module.
These outlets differ,depending on the version of
theHotSwap MBP module.
Caution :Do not use UPS outlets(4) to supply
equipmentbecause use of switch (45) on theHotSwap
MBP module would cutsupply to the equipment.
HotSwap MBP module operation
The HotSwap MBP module has a rotaryswitch (45) with
two positions:
Normal: the load is supplied by the UPS,LED (43) is on.
Bypass: the load is supplied directly bythe AC power
source. LED (44)is on.Load is not protected.
UPS start-up with the HotSwap MBP module
1. Check that the UPS is correctly connected to the HotSwap MBP module.
2.Start the UPS by pressing the button on the UPScontrol panel. LED (43) "UPS ON - OK to switch"on the HotSwap
MBP module goes ON (otherwise,there is a connection errorbetween the HotSwap MBP module and the UPS).
3. Set switch (45) to Normal position.The red LED onthe HotSwap MBP module goes OFF.
HotSwap MBP module test
1. Set switch (45) to Bypass position and check that the load is still supplied.
2. Set switch (45) back to Normal position.

614-40094-00
16
4 Interfaces and communication
4.1 Control panel
The screen provides useful information about the UPS itself, load status,events, measurements and settings.
The LED bar ⑨has been implemented to provide a quick visual reference of UPS status "at-a-glance".
①Power ON indicator (green)
②On battery indicator (yellow)
③Alarm Indicator (red)
④Escape
⑤Up
⑥Down
⑦Enter
⑧On/Off button
⑨Led bar
Led indicator
The following table shows the indicator status and description :
Indicator Status Description
Green On The UPS is "On" and the load is protected.
Yellow On The UPS is in battery mode and the load is protected.
Flashing The battery voltage is below the warning level.
Red On The UPS has an active alarm or fault. See troubleshooting page for additional
information.
Led bar
Static blue The UPS is "On" and the load is protected.
Flashing blue The UPS is on battery or the battery service age warning is reached.
Static red The UPS has an active alarm or fault.
Flashing red The UPS output has stopped due to a fault.

614-40094-00
17
4.2 LCD description
①Load status and measurements
②Equipment status icon
③Status / Message
④Battery status
As default, or after 5 minutes of inactivity, the LCD displays the screen saver.
The backlight LCD automatically dims after 5 minutes of inactivity. Press any button to restore the screen.
Note. If other indicator appears, see troubleshooting page for additional information.
The following table describes the status information provided by the UPS :
Operation status Possible cause Action
Standby mode
The UPS is OFF, waiting for start-up
command from user
Equipment is not power until button is pressed
during start up and the green "normal mode" LED
indicator is illuminated.
Normal mode
The UPS is operating normally. The UPS is powering and protecting the equipment.
In AVR mode
No beep
The UPS is operating normally but the
utility voltage is outside Normal mode
thresholds.
The UPS is powering the equipment through the
Automatic Voltage Regulation device. The equipment is
still normally protected.
On Battery
One beep every 10
seconds
A utility failure has occurred and the
UPS is in Battery mode.
The UPS is powering the equipment with battery
power. Prepare your equipment for shutdown.
End of backup time
1 beep every 3
seconds
The UPS is in Battery mode and the
battery is running low.
This warning is approximate, and the actual time to
shutdown may vary significantly. Depending on the
UPS Load, the "Battery Low" warning may occur before
the battery reaches 20% capacity remaining.

614-40094-00
18
4.3 Display functions
Press the Enter (⮠) button to activate the menu options. Use the two middle buttons (⯅and ⯆) to scrollthrough the
menu structure. Press the Enter (⮠) button to select an option. Press the (ESC) button to cancelor return to the previous
menu.
Menu map for display functions
Main menu Submenu Display information or Menu function
Measurements -
Load: [Total Load/Load (Primary)/Load (Group 1)/Load (Group 2)] : W, A, VA, pF
[Input/Output] : V, f
[Efficiency] : %
[Battery Info] : %, min, V, number of EBM, Age service, Age Warning
[Average power usage] : Toal, Primary, Group 1, Group 2
[Cumulative power] : Total, Since Primary, Since Group 1, Since Group 2
Control
Load Segments
Group 1: ON / OFF
Group 2: ON / OFF
These commands overrule user settings for load segments.
Start battery test Starts a manual battery test (possible if load >20% and battery >80%)
Change battery Disable charger, Replace battery, Update settings
Connectivity test Dry contacts test, Relay card test, Line failure test, Battery low test
Functions reset Reset fault state, Reset power usage, Reset battery life, Card reset, Restore
factory settings
Settings
Local settings Sets product general parameters, see User settings
Input / output
settings Sets input and output parameters
ON / OFF settings Sets ON / OFF conditions
Battery settings Sets battery configuration
Communication
settings
Sets communication parameters (input/output signals, remote signals, IPV4
address)
Event log
View alarms Displays the alarms stored
View events Displays the events stored
View all Displays the faults and events stored
Reset all Clears the faults and events stored
Fault log
View fault Displays the faults stored
Reset faults Clears faults

614-40094-00
19
Main menu Submenu Display information or Menu function
Identification Type / Model / Part Number / Serial Number / UPS Firmware / NMC Firmware /
IPV4 Address / IPV6 Address / Com card MAC Address
Registration Links to Eaton registration website

614-40094-00
20
4.4 User settings
The following table displays the options that can be changed by the user.
Submenu Available settings Default settings
Local
settings
Language
[English] [Français] [Deutsch] [Español] [Русский]
[Português] [Italiano] [Simplified Chinese] [Japanese]
Menus, status, notices and alarms, UPS fault, Event Log
data and settings are in all supported languages.
English
Automatic message for user
configuration when UPS is
powered for the first time.
Date / time Format: [International] [US] [International]
LCD Modify LCD screen brightness and contrast to be adapted
to room light conditions. [0]
Audible
alarm
[Enabled] [Disabled on battery] [Always disabled]
Enable or disable the buzzer if an alarm occurs. [Enabled]
Level: [0-8] [6]
Protected
access
[Enabled] [Disabled]
Allow the user to lock the settings modification. Password
is: 0577 [Disabled]
In/Out
settings
Output
voltage [200 V] [208 V] [220 V] [230 V] [240 V] [230 V]
Input
thresholds
[Normal] [Extended]
Extended mode authorises lower input voltage(150V)with
out transferring to battery.
This can be used if the load can withstand low voltage
supply.
[Normal]
Sensitivity
[High] [Low]
Low sensitivity extend the range of input frequency
accepted before transferring to battery.
[High]
Load
segments
[Auto start delay] UPS:[No delay]; Group1:[3s];
Group2:[6s]
[Auto shutdown delay] UPS:[Disabled]; Group1:
[Disabled]; Group2:[Disabled]
Overload
prealarm
[10%] … [105%]
Load % when overload alarm occurs [105%]
ON/OFF
settings Start/Restart
[Cold start]
[Auto restart]
[Auto start]
[Cold start] : ON
[Auto restart] : ON
[Auto start] : OFF