ECA Marina HDMI MAR-H-BA-108 User manual

1
10 Mountain View Drive • Shelton, CT 06484 • P:800.521.3175 • F:203.924.6687 • www.electri-cable.com
© ECA–April 2014—Product specifications subject to change without notice INSTALL-MARHD-041014
Innovative Power + Data Solutions
9065-0256 Rev C
Marina HDMI™Install Instructions

2
10 Mountain View Drive • Shelton, CT 06484 • P:800.521.3175 • F:203.924.6687 • www.electri-cable.com
© ECA–April 2014—Product specifications subject to change without notice INSTALL-MARHD-041014
Innovative Power + Data Solutions
9065-0256 Rev C
Marina HDMI™Install Instructions
Cauons & Warnings
WARNING: FAILURE TO FOLLOW CAUTIONS AND WARNINGS BELOW COULD RESULT IN ELECTRICAL SHOCK, FIRE, PROPERTY DAM-
AGE, PERSONAL INJURY OR DEATH.
Cauons:
 Read Instrucons · Read all warnings and operang instrucons before using.
 Never use in a wet environment. Never allow liquid of any kind to spill onto or enter any part of the product.
 Retain Instrucons · Retain these instrucons for future use.
 Follow Warnings · Read and follow all warnings and instrucons in these instrucons and marked on Equipment.
 Service · There are no user serviceable parts in this product unless described in the following pages. Do not open or modify this
product in any manner.
Warnings:
 Power Source · This product is only to be operated from the power source indicated on the product. Use only with a grounded
(neutral) conductor. For safety do not bypass or disable the third (grounding) pin.
 Power Disconnecon · To remove powered devices safely grasp device plug and pull straight from powered outlet. Do not pull
on device cord or remove plug from any angle other than straight from outlet. Never touch metal conductors on plug during
connecng or removal from product.
 Power Cord · Route products power cords where they will not be stepped on, pinched, have items placed on them or become a
tripping hazard. Never allow power cords to sit in any liquid or get wet in any manner.
 Locaon · This product is intended to be used in a dry environment only.
The Marina HDMI media sharing product uses 4 HDMI share cables, and a digital switcher to change between HDMI in-
puts. The users display their informaon on a single monitor when they click their “share” buon. The Marina provides
4 power outlets, and 4 USB charging ports. Other features include 2 customizable telecom plates, a 15’ HDMI monitor
cord, and a single 108” power cord.
Part Number Grommet Bezel Finish*
MAR-H-AL-108 Clear Anodized Brushed Aluminum
MAR-H-BA-108 Black Anodized Brushed Aluminum
MAR-H-GW-108 Gloss White Powder Coat
MAR-H-S-108 Silver Powder Coat
MAR-H-B-108 Black Texture Powder Coat
*Technology Bay is always graphite grey

3
10 Mountain View Drive • Shelton, CT 06484 • P:800.521.3175 • F:203.924.6687 • www.electri-cable.com
© ECA–April 2014—Product specifications subject to change without notice INSTALL-MARHD-041014
Innovative Power + Data Solutions
9065-0256 Rev C
Surface Preparaon:
1. Provide a cutout in surface for the Marina HDMI at desired locaon as shown in Fig. 1. (Note Fig. 1 repre-
sents underside of work surface)
2. Mark or pilot drill the locaon for center mounng screws as shown in Fig. 1. Note: Use cauon that any
pilot holes do not pierce nished surface.
Marina HDMI Grommet Installaon:
1. Adjust Grommet for table thicknesses less than 1.18” (30mm) by removing Grommet Skirt. For table thick-
nesses greater than 1.18” (30mm) proceed to step 2 below.
a. Remove 4 boom Grommet screws in each corner of Grommet. Retain screws for reinseron into
Grommet later. Note: Do not remove or loosen top Grommet screws.
b. Remove and discard skirt.
c. Reinstall the 4 screws removed above.
2. Insert Grommet into surface cutout and secure to table with 2 - #8 at head screws (not provided) through
mounng holes in side of Grommet, see Fig. 2. Ensure Grommet is centered in cutout and at to work sur-
face.
3. Check for smooth operaon of both doors.
Marina HDMI Technology Bay Installaon:
1. Install 1 - #10 pan head screw (not provided) into center mounng screw posion on underside of work
surface, see Fig.1. Do not fully ghten screw at this point. Note: Ensure all screws will not pierce nished
work surface.
2. Insert middle ange slot of one end of the Marina onto mounng screw to support the Marina while in-
stalling 2nd - #10 pan head screw (not provided) align with the other center mounng screw posion. Do
not fully ghten screws at this point.
3. Center the Marina in the cutout and secure to underside of surface using remaining holes in side anges.
Note: It is important that the Marina is centered in cutout and there is a consistent air gap between the
Marina and Grommet.
4. Tighten center screws from step 1 and 2 above.
Making Connecons:
1. Connect HDMI cable provided between Marina HDMI output port, see Fig. 3, and screen HDMI input port.
2. Connect power cord to 120 VAC outlet.
Operaon:
1. To verify that the switcher is operang as designed, connect two or more inputs devices (laptops or tab-
lets) to the user HDMI “Share” cords and switch the display between the units. If no image is displayed on
your monitor, conrm the monitor’s input seng is correct. Conrm the monitor to Marina output connec-
ons are secure. Visual Note: check the display window on the side of the unit. In the center INPUTS win-
dow there should be one LED lit. In the right window for signals, there should be the LED for the output lit
and one inputs signal LED lit for each device connected to the share cables, Fig. 4.
Marina HDMI™Install Instructions

4
10 Mountain View Drive • Shelton, CT 06484 • P:800.521.3175 • F:203.924.6687 • www.electri-cable.com
© ECA–April 2014—Product specifications subject to change without notice INSTALL-MARHD-041014
Innovative Power + Data Solutions
9065-0256 Rev C
Marina HDMI™Install Instructions
Fig. 2
Marina Grommet Mounng:
Fig. 3
Connecons:
Fig. 4
Operaon:
Fig. 1
Surface Cutout Dimensions:

5
10 Mountain View Drive • Shelton, CT 06484 • P:800.521.3175 • F:203.924.6687 • www.electri-cable.com
© ECA–April 2014—Product specifications subject to change without notice INSTALL-MARHD-041014
Innovative Power + Data Solutions
9065-0256 Rev C
Marina HDMI™Install Instructions
Warranty
This product is warranted for a period of one (1) year from the date of purchase. This warranty is null and void in the case of
abuse, uses outside its normal intended use, or field modifications made in any manner.
Marina HDMI™ technical specicaon:
 Power
 4, 120 VAC spill resistant receptacles.
 4, USB charging ports that work with USB compable devices. Each pair capable of (2.1A, 11 Was, 5V/DC.)
 Integral circuit breaker protecon. (located on side of unit)
 Video
 Extron:
 4x1 HDMI Switcher
 HDMI Show Me cables
 Maximum data rate—6.75 Gbps (2.25 Gbps per color)
 Maximum pixel clock—165 MHz
 Formats—RGB and YCbCr digital video
 Standards— HDMI
 Input— 4
 Output— 1
 Regulatory compliance
 Safety—cETLus
 EMI/EMC—CE, C-ck, FCC Class A, ICES, VCCI
 Environmental—complies with appropriate requirements of RoHs and WEEE.
 Shipping
 Weight—20 lbs.
 Carton— 16” X 12” X 12”