Eclipse EC-P10 User manual

EC-P10
10-20 Zone Intruder Alarm System
Installation Manual

2 P0016-LI-02.01
Contents
1.System Overview ........................................... 4
System Configuration ............................................................. 4
Control Panel .......................................................................... 5
Remote Keypads .................................................................... 5
EC-LED Remote Keypad ............................................................ 5
EC-LCD Remote Keypad ............................................................ 5
Expansion Modules ................................................................ 5
EC-EX10 Zone & Output Expander ........................................... 5
EC-EX10/I Zone Expander ........................................................ 5
EC-COM/IP Communication Module...................................... 5
EC-USB-Link ............................................................................ 5
Upload/Download Software................................................... 5
2.Installation..................................................... 6
Installation Sequence............................................................. 6
Control Panel .......................................................................... 6
Mounting .................................................................................... 6
Wiring the Control Panel ........................................................... 6
Control Panel Layout ................................................................. 7
PCB Layout ................................................................................. 8
Connecting Devices to the Network.......................................10
Remote Keypads ..................................................................11
PCB Layouts .............................................................................11
Wiring Detection Devices .....................................................11
Normally Closed.......................................................................11
Normally Open .........................................................................11
Single EOL - N/C ......................................................................12
Double EOL...............................................................................12
Triple EOL .................................................................................12
Loudspeaker Connections ...................................................12
External Sounder/Strobe Connections................................13
TR ..............................................................................................13
0V..............................................................................................13
+12 ...........................................................................................13
Bell (1) ......................................................................................13
Strobe (2) .................................................................................13
Panel Outputs 1 - 5...............................................................13
2-Wire Smoke Detectors ......................................................13
Telephone Line Connections................................................14
Commissioning .....................................................................14
Power-Up Options Menu..........................................................14
3.Programming the Control Panel ................ 15
Introduction...........................................................................15
Exiting Engineer’s Program Mode........................................15
Menu Navigation and Data Entry.........................................16
LCD Navigation ........................................................................16
Selection List............................................................................16
Bit Toggle Selection .................................................................17
Number Entry ...........................................................................18
String Edit - Number Mode .....................................................18
String Edit - Text Mode ............................................................19
1. Zone Programming...........................................................19
Zone Type .................................................................................19
Zone Wiring ..............................................................................20
Zone Attributes ........................................................................20
Zone Bypass Options...............................................................21
Zone Chime.............................................................................. 21
Zone Soak Test........................................................................ 21
Zone Text ................................................................................. 21
Zone Link ................................................................................. 21
2. Arming Control.................................................................. 22
Arming Timers ......................................................................... 22
Arming Modes ......................................................................... 22
Arm Options 1.......................................................................... 22
Arm Options 2.......................................................................... 23
Arm Keyswitch Control............................................................ 23
Auto Arm/Disarm .................................................................... 23
3. System Configuration....................................................... 24
System Timers......................................................................... 24
System Counters ..................................................................... 24
Hardware - Volume Levels...................................................... 25
Hardware - Output Monitoring ............................................... 25
Hardware - Monitoring ............................................................ 25
Configuration ........................................................................... 25
Control Timers ......................................................................... 26
Banner Text ............................................................................. 26
Remote Control Labels ........................................................... 26
Voice Options........................................................................... 26
Activate by Link Control .......................................................... 26
Voice Message Options .......................................................... 26
System Links ........................................................................... 27
4. Keypad Configuration ...................................................... 28
Keypad Options 1.................................................................... 28
Keypad Options 2.................................................................... 28
Keypad Sounds ....................................................................... 28
5. Expander Configuration ................................................... 29
Expander Options.................................................................... 29
Expander Sounds .................................................................... 29
Expander Outputs ................................................................... 29
Expander Output Attributes.................................................... 29
6. Panel Outputs and Devices ............................................. 30
Panel Output Type................................................................... 30
Panel Output Attributes .......................................................... 30
Output Types ........................................................................... 30
00: Global ................................................................................ 30
Group 02: Control Timer......................................................... 31
Group 03: Remote Control ..................................................... 31
Group 04: Link Control ........................................................... 32
Group 10: Zone Count ............................................................ 32
Group 20: Zone Mimic............................................................ 32
Group 30: Zone Alarm ............................................................ 32
Group 40: Zone Tamper ......................................................... 33
Group 50: Zone Masked......................................................... 33
Group 60: Zone Fault.............................................................. 33
Group 70: Zone Bypassed...................................................... 33
Group 80: User Access ........................................................... 33
Communication Ports ............................................................. 33
GSM & SMS Centre................................................................. 33
IP Configuration....................................................................... 34
7. On-board Communicator ................................................. 35
ARC 1-4: Telephone Number.................................................. 35
ARC 1-4: Account Number...................................................... 35
ARC 1-4: Protocol .................................................................... 35
ARC 1-4: Protocol Options ...................................................... 35
ARC 1-4: Call Sequence/Attempts......................................... 35
ARC 1-4: Reported Event Groups........................................... 35

P0016-LI-02.01 3
ARC 1-4: Cancel on Success...................................................36
ARC 1-4: IP Address.................................................................36
ARC 1-4: IP Port Number.........................................................36
Options: Auto Test Call Period ................................................36
Options: Auto Test Call Time...................................................36
Options: Auto Test Days ..........................................................36
Options: PSTN Pre-Dial Number .............................................36
Fast Format: Reporting Channels ..........................................36
Fast Format: Restore Channels..............................................37
Fast Format: Open/Close Channels.......................................37
Channel Type ...........................................................................38
Channel Attributes...................................................................38
Speech Dialler: Telephone Numbers 1 and 2 .......................38
Speech Dialler: Dial Sequence ...............................................38
Speech Dialler: Trigger Type ...................................................38
UDL Options .............................................................................38
UDL Password ..........................................................................38
UDL Ring Count........................................................................39
Call-Back Number....................................................................39
UDL Dial Sequence..................................................................39
UDL Remote IP Address ..........................................................39
UD Remote IP Port...................................................................39
UDL Account Number ..............................................................39
8. System Users....................................................................40
User Access Code ....................................................................40
User Type..................................................................................40
User Locked By ........................................................................40
User Name ...............................................................................40
User Link...................................................................................40
9. Utilities ..............................................................................41
Time and Date..........................................................................41
User Menus...........................................................................41
Away ArmA.........................................................................41
Stay Arm 1S......................................................................41
Stay Arm 22*...................................................................41
Stay Arm 33*...................................................................41
Walk Test11*.................................................................41
Test Bell & Outputs12*.................................................41
Do Test Call13* .............................................................41
View Event Log21*........................................................41
Print Event Log22*........................................................41
Call UDL23*...................................................................41
Chime on/off24* .......................................................... 41
Change Code81* .......................................................... 41
Program Mode91*........................................................ 41
View Zone Status92* ................................................... 41
Exit Menu99*................................................................ 41
Log Events ............................................................................ 42
LED Indications..................................................................... 45
Fault & Status Messages..................................................... 45
Resetting Faults & alarms ...................................................... 45
4.Specifications.............................................. 46
EC-P10 Control Panel........................................................... 46
Electrical .................................................................................. 46
Environmental ......................................................................... 46
Physical .................................................................................... 46
EC-LED Remote Keypad....................................................... 46
Electrical .................................................................................. 46
Environmental ......................................................................... 46
Physical .................................................................................... 46
EC-LCD Remote Keypad....................................................... 46
Electrical .................................................................................. 46
Environmental ......................................................................... 46
Physical .................................................................................... 46
EC-EX10/I Zone Expander ................................................... 46
Electrical .................................................................................. 46
Environmental ......................................................................... 46
Physical .................................................................................... 46
EC-EX10 Zone & Output Expander ...................................... 47
Electrical .................................................................................. 47
Environmental ......................................................................... 47
Physical .................................................................................... 47
EC-COM/IP Communication Module ................................... 47
Electrical .................................................................................. 47
Environmental ......................................................................... 47
Physical .................................................................................... 47
Standards ............................................................................. 47
Safety ....................................................................................... 47
EMC .......................................................................................... 47
Security .................................................................................... 47
Warranty ............................................................................... 47

4 P0016-LI-02.01
1. System Overview
System Configuration

P0016-LI-02.01 5
Control Panel
The EC-P10 control panel is an advanced intruder alarm system
with 10 on-board zones and on-board multi format communicator.
The system can be expanded to 20 zones using the 10 zone
expansion modules (EC-EX10 or EC-EX10/I). The system is ideally
suited to domestic and small commercial installations.
The control panel provides a multi-channel integrated speech
dialler and voice annunciation feature. Voice messages are
recorded via a touch tone telephone or by using the Eclipse UDL
software package.
Remote arming and disarming and system control can also be
carried out by calling the protected premises with a touch-tone
telephone. On answering the incoming call you are greeted with a
voice prompted menu.
The system can be further enhanced by using the EC-COM/IP
module which provides both IP and X-10 connectivity. X-10 is a
simple home automation protocol that uses the existing mains
wiring to communicate with X-10 compatible devices via a XM10U
controller. Once the EC-COM/IP is installed, both the system and
X-10 devices can be controlled remotely using smart phone apps.
A choice of either LCD or LED remote keypads is available. Other
features include:
f10 programmable on-board zones
f5 programmable outputs (1Amp rated)
fOn-board communicator/modem/speech dialler
fLocal or remote upload/download
f250 event log
f1.5 Amp switched mode power supply
fTwo communication ports for accessories etc
fLoudspeaker output
fSelectable battery charging rate
fReal time clock
fTwo-wire smoke detector support
fFlash upgradable
Remote Keypads
The EC-P10 will accept up to a maximum of 4 remote keypads. All
remote keypads require a 4-wire connection to the control panel
using standard alarm cable. The following remote keypad models
are available:
EC-LED Remote Keypad
The LED keypad features a dual 7 segment display for displaying
zone status and system fault messages. A set of dedicated
system status LEDs for AC, Ready, Armed, Trouble, Bypass, Alert
and Alarm are also provided. Other features include:
f4-wire connection using standard alarm cable
fInternal sounder
fBacklit keyboard
EC-LCD Remote Keypad
The LCD keypad features a 2 x 20 character blue display for
showing all zone status and system fault messages. A set of
dedicated system status LEDs for AC, Trouble and Alert are also
provided. Other features include:
f4-wire connection using standard alarm cable
fInternal sounder
fBacklit keyboard
Expansion Modules
The following expansion modules are available:
EC-EX10 Zone & Output Expander
The EC-EX10 is a housed zone and output expansion module that
is connected to the 4-wire control panel network. Features
include:
f10 fully programmable zone inputs
f10 programmable outputs (8 x 100mA; 2 x 1Amp)
fInternal piezo sounder
f16Ωloudspeaker connection, with programmable volume
fTamper protection
fEngineer keypad port
fStylish housing
EC-EX10/I Zone Expander
The EC-EX10/I is a housed zone expansion module that is
connected to the 4-wire control panel network. Features include:
f10 fully programmable zone inputs
fTamper protection
fStylish housing
EC-COM/IP Communication Module
The EC-COM/IP is an IP based communicator and X-10 home
automation interface PCB module. Features include:
fEthernet connection to LAN/WAN
fRemote access via Eclipse UDL or smart phone app
fAlarm reporting via LAN/WAN to PC based alarm receiver
fX-10 port for automating X-10 devices via XM10U/E
controller
fX-10 devices controlled via the system or smart phone app
fPCB module clips into EC-P10 control panel housing
EC-USB-Link
The EC-USB-Link provides USB connectivity between the EC-P10
and the host computer. It is required when a direct connection is
required between the Eclipse UDL software package and the
control panel.
Upload/Download Software
Eclipse UDL is a Windows® based software package that can be
used to remotely or locally program and diagnose the Eclipse
range of security systems. Features include:
fSimple intuitive user interface
fLocal or remote via modem and IP
fSystem remote control
fAdvanced system diagnostics
fMulti language support
fSystem audit trail

6 P0016-LI-02.01
2. Installation
Installation Sequence
Before attempting to install the alarm system, read this section.
Once you have an overall understanding of the installation
sequence, carefully work through each step.
1. Design the Layout
Make a rough sketch of the premises to get an idea of where all
alarm detection devices, keypads and other modules are to be
located.
2. Mounting the Control Panel
The control panel must be mounted within the protected area
close to an unswitched AC power source and the incoming
telephone line.
You must complete all wiring before connecting the battery, or
applying AC to the panel.
3. Install the Remote Keypads
Mount the remote keypads at locations that are easily accessible
during entry and exit from the protected area. Connect the remote
keypads to the control panel.
4. Zone Wiring
Install detection devices and connect to control panel or
expander.
5. Other Wiring
Complete all other wiring including external/internal sounders
and telephone line connections.
6. Apply Power to the Control Panel
Once steps 1 to 5 are completed, apply power to the control
panel. First, connect the red battery lead to the positive terminal
and the black lead to negative. Then, connect the AC.
7. Program the System
If available use the Eclipse UDL software package to program the
system, if this is not available program this system in accordance
with the procedures in Section 3.
8. Testing the System
Test the system thoroughly to ensure that all features and
functions are operating as required.
Control Panel
Mounting
Mount the control panel on a flat, plumb wall using at least three
appropriate screws. The rear casing has been designed with a
central key-hole slot so that mounting is possible without
removing the Printed Circuit Board (PCB).
The angled slot in the lower corner has been provided to allow the
panel to be levelled easily. If the PCB has to be removed, carefully
pull back the two front PCB securing clips, lift the front of the PCB
and slide it downward. To replace the PCB simply reverse the
above procedure.
It is essential to ensure that none of the fixing slots or cable
entries are accessible after fixing.
Mains cabling must be secured (e.g. with a cable tie) to one of the
anchor points provided.
Wiring the Control Panel
WARNING: ELECTRICITY CAN KILL
BEFORE connecting the control panel ALWAYS
disconnect the supply at the consumer unit.
If in ANY doubt consult a qualified electrician.
ONLY connect the mains supply to the mains terminal
block, NEVER connect the mains supply directly to the
PCB.
The system installation MUST be carried out in
accordance with the national safety standards, for
example EN 60950: 1992.
ALWAYS refer to National Wiring Regulations when
conducting installation.
An appropriate and readily accessible disconnection
device (e.g. an unswitched fused spur) MUST be
provided as part of the installation.
The disconnection device must NOT be fitted in a
flexible cord.
Where identification of the neutral in the mains supply
is NOT possible, a two-pole disconnection device MUST
be used.
The building mains supply MUST incorporate
appropriate short-circuit backup protection (e.g. a fuse
or circuit breaker) of High Breaking Capacity (HBC, at
least 1500A).
Use mains cable of adequate carrying capacity for the
rated current (i.e. at least 0.75mm2).

P0016-LI-02.01 7
Control Panel Layout
1
3 4 6
2
5
1. Main Printed Circuit Board (PCB)
The main PCB that provides the terminals connection to remote
keypads and detection devices, see PCB Layout on next page for
full details.
2. Switched Mode Power Supply
The switch mode power supply module is housed under this
protected area and provides power to the main PCB via the three-
way harness.
3. Mains Connection
The AC Mains supply is connected to a 3 way Euro Type fused
terminal block, which is fitted with a 500mA fuse.
Fuse T500mA
L
E
N
To Power Supply
Module
4. Mains Supply Cable Entry
The mains supply cable must be routed into the control panel
housing via this cable entry.
5. Communication Module
An optional Eclipse communication Module can be clipped into
the housing under the main PCB.
5. Standby Battery
The system housing will accept a 12V 7Ah battery to provide
continued operation in the event of an AC mains failure. Connect
the red battery lead to the positive terminal of the battery and
then connect the black battery lead to the negative terminal.
Control Panel
RD
Network
BAT
12V 7Ah
Sealed Lead Acid Battery
The system will only become “live” when the AC supply is
connected or the “Battery On” pins are shorted.

8 P0016-LI-02.01
PCB Layout
1
2
3
4 5 6 7 6 8 9 10 11
12
13
14
15
161616171618
1. PSU Connector
The harness from the switched mode power supply module plug
onto this connector and provides the power (13.7V) to power the
system.
2. Engineer’s Remote Keypad Connector
An engineer’s remote keypad maybe plugged onto to this
connector so that system programming and testing can be carried
out at the location of the control panel.
3. Lid Tamper Switch
This switch detects when the cover is in position and the screw is
fully secured. The tamper is designed to activate when the screw
is undone.
4. Battery Connections
A 12V rechargeable battery must be connected to these two
terminals in order to provide continuous system operation in the
event of mains failure. The battery output is protected by an auto
resetting fuse (PTC) rated at 1.6 Amp.
5. Network Connections
The network terminals provide connections to the remote keypads
and zone expanders. The + and – terminals provide power whilst
the R and R terminals are the data signals.
6. Zone Inputs 1 to 10
Detection devices such as movement sensors, vibration and door
contacts are connected to the zone input terminals. There are
several ways in which to wire a detection device (see page 11).
Each zone is fully programmable, see page 19 for information on
programming zones.
7. Auxiliary 12V
These terminals provide auxiliary power for detection devices that
require 12V power, e.g., moment sensors. The auxiliary output is
protected by an auto resetting fuse (PTC) rated at 1.1 Amp).
8. Speaker
These terminals are used for driving 16Ωextension loudspeakers
(see page 12).
9. Bell Tamper Return
This terminal is connected to the tamper return connection from
an external sounder unit. If it is not required link it to 0V.
10. External Sounder 12V
These terminals provide power for external sounder units. The
output is protected by an auto resetting fuse (PTC) rated at 1.1A.
11. Panel Outputs 1 to 5
These are fully programmable high current (1 Amp), switched
negative supervised outputs. Panel outputs 1 and 2 default to bell
and strobe operation, but can be programmed for other functions
if required, see page 30 for programming details. Each output can
also be programmed for supervision monitoring, see page 25.
12. Two-Wire Smoke Detector Enable
Set this link as shown when connecting 2-wire smoke detectors to
Panel Output 5.
2-wire Smoke Detectors Enabled: Panel Output 5
must be programmed as “2-wire Smoke” (0047)
and smoke detectors must be connected as shown
page 13.
2-wire Smoke Detectors Disabled: Panel Output 5
will function as a normal output.
13. Communication Ports 1 and 2
Two serial communication ports 1 and 2 are provided for local
downloading and for third party devices.
14. RJ11 Telephone Line Connector
An RJ11 connector is provided so that the panel can be
connected to the telephone line via a standard RJ11 patch lead.
15. Telephone Line Connections
Telephone line connections (see page 14).
16. Power/Status LED
On steady when either AC or standby battery is present. Flashes
when the on-board communicator is dialling or sending data.
17. Battery Charging Rate
The standby battery can be recharged at different rates:

P0016-LI-02.01 9
300mA: This is the recommended charge rate for a
7Ah standby battery. The system will fully recharge a
flat battery within 24hours.
750mA: This is the recommended charge rate for a
17Ah standby battery. The system will fully recharge
a flat battery within 24hours.
18. Battery On (Kick Start)
When powering the system from battery only, the “Battery On”
pins must be momentarily shorted together with a plain blade
screwdriver or similar to kick start the power supply into
operation.

10 P0016-LI-02.01
Connecting Devices to the Network
Before connecting devices to the control panel network, isolate
ALL power from the control panel (AC Mains & Battery). Do not
continue if there is still power present on the control panel.
Connecting devices with power still present on the
control panel may damage the device or control panel
and invalidate any warranty.
Remote keypads and zone expanders are all connected to the
same network terminals located at the bottom left hand corner of
the control panel and may be connected serially (daisy chain), in
parallel (star) or any combination of the two.
Network Connections
The network is made up of four terminals incorporating power and
data. To ensure correct operation, all four terminals on the device
must be connected to the corresponding terminals on the control
panel, or previous device. The table below shows each terminal
and its description:
+ +12V Supply
- 0V Supply
R Data Return
D Data I/O
Control Panel
Network
500 metres
Remote Keypad
Address = 1
12V
RD
0V
Remote Keypad
Address = 3
RD
Remote Keypad
Address = 2
12V
RD
0V
12V
RD
0V
Zone & Output Expander
Address = 1
12V
RD
0V
12V
RD
0V
IN OUT
To additional devices
Cable Type and Distances
For improved immunity to electrical noise, the use of screened 4
core cable is recommended. The screen should be twisted
together and wired into the (–) terminal at the control panel only.
The maximum recommended distance for devices when using
standard 7/0.2 alarm cable is:
f250m for each branch when using the star (parallel)
configuration
fWhen using a daisy chain (series) configuration the
maximum distance will depend on the number of devices
connected on the chain. The more devices that are
connected, the shorter the distance to the last device (this is
due to voltage drop in the cable)
Whichever method of wiring configuration is used, ensure that the
voltage between the ‘+’ and ‘–’ terminals at each device is no
lower than 10.0V when the system is running on the standby
battery.
Overcoming Voltage Drop
There are several ways to overcome voltage drop:
fUse thicker lower resistance cable. Standard 7/0.2 alarm
cable has a resistance of 8Ωper 100m
fDouble up on the power connections – this will require using
a 6 or 8-core cable rather than a 4-core cable
fInstall a power supply to power the device locally, remember
to common the two negative connections
Installing a Power Supply
When a power supply is installed, the 0V connections on the
power supply must be connected through to 0V on the control
panel and the +12V connection between the control panel and
the device must be disconnected (see figure below).
Control Panel
Network
500 metres
Remote Keypad
Address = 1
12V
RD
0V
Remote Keypad
Address = 2
Remote Keypad
Address = 3
Remote Keypad
Address = 4
RD
12V
RD
0V
12V
RD
0V
12V
RD
0V
1km
Power Supply
12V
0V
Disconnect +12V
from control panel