EcoQuest Ozone Blaster 2 User manual

Ozone Blaster 2
By EcoQuest
3500/7000 mg/hr. Ozone Generator
Commercial Air Purifier
OWNER’S MANUAL
Please read all of the information provided in this owner’s manual
before operating your new Commercial Air purifier.

CAUTION
RISK OF ELECTRICAL
SHOCK DO NOT OPEN
ATTENTION
Caution: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO
NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVCE PERSONNEL.
This “bolt of lightning” indicates that uninsulated material
within your unit may cause an electrical shock. For the safety
of everyone, do not remove product covering.

INTRODUCTION
This commercial air purifier is an advanced and convenient
contaminant remediation product. High-powered oxidation in a
compact, lightweight, rugged and simple design. Utilizing controlled
corona discharge ozone technology developed specifically to reduce
odors and smoke in unoccupied spaces, ideal for treatment of homes,
offices, automobiles, boats and More!
Model:
Ozone Blaster 2
Rated Voltage:
Europe AC 220-240V/50-60Hz
USA/Japan AC 100-120V/50-60Hz
Power Consumption:
100W
Ceramic Plate Size(2 plates):
90X50MM
Air Volume:
Max 100 CFM(2.8 M3/min)
Active Oxygen(on) ：
3.5-7.0 g/h
Sound Level(DB):
45 Db
Product size(mm):
W210xH180xD260MM
Weight:
2.9Kgs(6.38Lbs)

Operating your Ozone Blaster 2
(Front View)
Timer Control Knob Turn clockwise to set the timer for timed
operation up to TWO hours.
Indicator Light Illuminates when unit is in operation.
High-low switch ozone high and low change-over switch

(Back View)
Fuse Holder Houses removable fuse. (Two amp, 0.79 inch in
length)
Power Cord Grounded cord

Ozone Blaster 2 removes odors, bacteria, mold and viruses in
unoccupied spaces. The unit has a timer that will enable it to run for a
maximum duration of 2 hours. The timer will then shut the purifier off.
To operate the Ozone Generator Air Purifier:
Close off the desired area to be treated.
Remove all occupants and pets.
Position the unit as close as possible to the odor source.
In such environments as motels that have individual heating
and cooling systems, turn the fan on and set on re-circulate.
Set timer to desired time and leave the room.

When your Ozone Blaster 2 no longer produces enough ozone, replace
the ozone plates.(Usual replacement after 6000 hours of operation)
How to replace the ozone plate:
1) Turn the unit off and unplug from outlet.
2) Use a screwdriver to unfasten cover screw and remove cover.
3) Pull ceramic plate out of ozone generator module.
4) Install ceramic plate as shown in above figure (be careful not to
drop the plate).

If you suspect a problem with your unit check the following:
1) Unit plugged in properly.
2) Unit is properly grounded to avoid potential shock.
3) Fuse is installed properly and in good condition. To replace
fuse, pull out the plastic fuse holder, remove old fuse and insert
new fuse. Replacement fuse must be two amp (0.79 inch).
Refer to picture as follows:
The ozone generator commercial air purifier comes with a one Year
Limited Warranty.
This device is warranted to be free from all defects in material in normal
use for a period of 1 year from date of purchasing. The warranty is
granted only to the original purchaser. This warranty provides for the
repair or replacement of the unit, replacement product or parts may
included re-manufactured or refurbished parts or components.
This warranty does not cover part of the unit that requires replacement
under normal use. Any damages or malfunctions caused by negligence,
abuse, or use not in accordance with the owner’s manual are not
covered by this warranty. Likewise, any defects or damages caused by
unauthorized service.