Edco CPU-10FC Datasheet

Printed in USA
©2006
Page 1
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
PARTS LIST MANUAL
10” SELF-PROPELLED SCARIFIER
REVISED STARTING SERIAL NO. 060210009
MODEL
CPU10FC-20H
SHOWN
*SKU NO. MODEL POWER OPTION
73400 CPU10FC-20H 20 HP HONDA GX620, GASOLINE ENGINE
73500 CPU10FC-13H 13 HP HONDA GX390, GASOLINE ENGINE
73700 CPU10FC-12KC 12 HP KOHLER COMMAND CS12T, GASOLINE ENGINE
73600-230 CPU10FC-10B/230/3 10 HP BALDOR 3 PHASE MOTOR 230 VOLT, 23 FLA, ELECTRIC MOTOR
73600-460 CPU10FC-10B/460/3 10 HP BALDOR 3 PHASE MOTOR 460 VOLT, 11.5 FLA, ELECTRIC MOTOR
*ADD AN “R” SUFFIX TO ANY SKU NO. LISTED FOR SCARIFIER WITH OUTRIGGER FRONT WHEELS
CPU10FC SCARIFIERS

Printed in USA
©2006
Page 2
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING
TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly.
SAFETY
MESSAGES
The safety instructions are proceeded by a graphic alert message of
DANGER, WARNING, or CAUTION.
Indicates an imminent hazard which, if not avoided,
will result in death or serious injury.
Indicates an imminent hazard which, if not avoided,
can result in death or serious injury.
Indicates hazards which, if not avoided, could result
in serious injury and or damage to the equipment.
GASOLINE
Powered Equipment
• Do not operate gasoline powered equipment without adequate ven-
tilation. Carbon monoxide is an invisible, odorless gas that can kill.
ELECTRICAL
Powered Equipment
•ELECTRICAL HAZARD - Be sure equipment is properly grounded.
Failure to comply could kill or result in serious injury.
The engine exhaust from this product contains chemicals known to
the State of California to cause cancer, birth defects or other reproduc-
tive harm.
!!
!!
!
GENERAL INSTRUCTIONS
• You must read and understand the operators instruction manual and
all other manuals associated with this machine. For your safety
and the safety of others around you, it is extremely important to fully
understand how to operate this machine in the way it was intended.
Different model machines or older/newer versions of the same model
may have different parts and controls that you need to understand.
If instructions are not readable or available DO NOT USE this
machine and contact the factory for a replacement Manual.
• You must be able to physically handle the bulk weight and power of
this machine. If not properly controlled this machine can cause
death or serious injury.
• Do not operate this machine in an impaired mental state. You must
be able to exercise good judgement and reactions to maintain a safe
working environment.
• This is a “one person” machine which means only one operator can
be operating the machine at any one time. For the safety of others,
maintain a safe operating distance to other personnel. Your work
area should be defined and appropriately marked so bystanders
and coworkers do not stand or walk near this machine and end up
seriously injured by flying debris or exposing them to harmful noise
or dust.
• This equipment is for Commercial use. Although this is a “one
person” machine your work team should understand how to shut
this machine off and quickly get medical help if an accident strikes
the operator.
• Keep all guards in place during operation. The guards are to pro-
vide protection from inadvertent contact with dangerous moving
parts, pinch points, or hot surfaces.
• Wear appropriate Personal Protective Equipment (PPE) including
safety glasses, safety boots, work gloves, respiratory protection,
!!
!!
!
hearing protection, and head protection. Do not wear loose clothing
that can get tangled in moving parts. Failure to do so could result in
dismemberment or death. Wear an approved respirator when re-
moving hazardous materials or when grinding/cutting dry materials.
Some dust particles such as concrete dust can contain silicate
particles which can cause silicosis (a very serious lung disease).
Contact NIOSH or OSHA for further details. When wet grinding/
cutting, avoid contact with the concrete/asphalt slurry which can
cause serious skin irritations.
• You must maintain this machine per the maintenance schedule in
the operator manual. Remember before adjusting, servicing, or
fueling this machine, disconnect the source of power to the machine
by disconnecting the spark plug (Gas models), or by unplugging the
electrical power cord (electric models) or air hose (Pneumatic
models) AT THE MACHINE so you can assure yourself it remains
unplugged while you are working on it. Do not modify this machine.
Use only genuine EDCO parts and accessories. Repairs and ser-
vice should be performed by approved EDCO dealers or authorized
technicians.
• You should look carefully around the area before you begin work so
you can identify potential hazards such as deck inserts, pipes,
columns, openings, electrical cords or outlets, or any other objects
protruding from the slab surface.
• This machine has no brain so you must use your own. There is no
substitute for safety. The safety decals on the machine are to serve
as a reminder for information you must already know before you
begin using this machine. Take a moment to reread the safety
decals each time you use the machine. If your machine is missing
any decals, contact the factory for a replacement (EDCO 1-800-
638-3326).

Printed in USA
©2006
Page 3
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
PARTS LIST MANUAL
MODEL CPU10FC
Section Page Number
Safety Messages/General Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
How To Order Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Illus. 1: Frame Grouping . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,5
Illus. 2: Lifting System Grouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,7
Illus. 3: Transmission Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8,9
Illus. 4: Clutch & Rear Axle Grouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10,11
Illus. 5: Honda Engine Grouping For 20HP Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,13
Illus. 6: Engine Grouping For 12HP & 13HP Units. . . . . . . . . . . . . . . . . . . . . . . . . . . 14,15
Illus. 7: Electric Motor Grouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16,17
Illus. 8: Belt Drive Grouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18,19
Illus. 9: Drum Bearing & Axle Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Illus. 10: Standard 4-Shaft Cutter Drum Grouping . . . . . . . .. . . . . . . . . . . . . . . . . . 21
Illus. 11: Optional 6-Shaft Cutter Drum Grouping . . . . . . . . . . . . . . . . . . . . . . . . . 22
Illus. 12: Optional Diamond Grooving Head Grouping . . . . . . . . . . . . . . . . . . . . . . . 23
Limited Equipment Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Page
Date of Purchase ______________________
Name of Machine
__________________
Model # ______________________________
Serial # ______________________________
Belt Size(s) ___________________________
FILL IN INFORMATION BELOW
Toll Free: 1-800-638-3326
FAX: [phone]
email: [email protected]
www.edcoinc.com
To insure product safety and reliability, always
use genuine EDCO replacement parts when making
repairs to the equipment.
When calling for parts, specify the MODEL
and SERIAL NUMBER of the machine which can be
found on the NAME PLATE. Keep that information in
the space provided. In addition to this information,
give part number, description and quantity as listed
on the parts list to your parts representative.
Please note: Due to improvements and
changes in the equipment, the illustrations shown may
be different than the actual machine.
HOW TO ORDER REPLACEMENT PARTS

Printed in USA
©2006
Page 4
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 1: FRAME GROUPING
15
14
11
13
12
12
11
10 9
8
76
19
36
35
*
*
38
24
28
22
20
18
16
17
3
4
5
2
30 31
32
29 28
27
26
25
23
33
34
1
40
41
42
21
45 46
47
44
43
37
39
48
49 50

Printed in USA
©2006
Page 5
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ITEM# PART# DESCRIPTION QTY.
1 64401 MAIN FRAME 1
2 64007 CONSOLE 1
3 10055 SCREW, CAP 3/8-16 x 1 3
4 10811 WASHER, LOCK 3/8 3
5 10025 WASHER, FLAT 3/8 3
6 10070 WASHER, HOSE 3/4 1
7 80021 CONN., SWIVEL FEM. 3/4HOSE X 1/2MPT (INCLUDES ITEM 6) 1
8 10711 VALVE, BALL 1/2 FPT 1
9 10724 ELBOW, STREET 1/2 NPT x 90°(BLACK) 1
10 10799 BARB, ELBOW 90°, 3/8 HOSE x 1/4 MPT 1
11 10714 CLAMP, HOSE SIZE M4 ADJ. TO 5/8” 2
12 64058 HOSE, WATER 3/8”ID x 37”L 1
13 50075 BARB, 3/8 HOSE x 1/4 MPT 1
14 10716 ELBOW, STREET 1/4 NPT x 45°(BRASS) 1
15 80029 NOZZLE, SPRAY 1/4 NPT(BRASS) 1
16 61108 GRIP, HAND 1” MODEL SX 2
17 51024 HANDLE BAR 24”L 2
18 10145 PIN, DETENT RING 3/16 x 1-5/16” EFF. L 2
19 51230 KNOB, STAR CLAMPING(3/8-16 x 1 STUD) 2
20 10837 BOLT, EYE 1/2-13 x 1-1/2 x 1-1/8”ID 1
21 10312 WASHER, FLAT 1/2 SAE 1
22 10155 NUT, HEX NYLON LOCK 1/2-13 1
23 64070 COVER, BELT 1
24 64071 SCREW, CAP 1/2-13 x 5-1/2 1
25 64072 SPACER, BELT COVER 1/2”ID x 3-7/8”L 1
26 10045 WASHER, LOCK 1/2 1
27 10417 NUT 1/2-13 1
28 10312 WASHER, FLAT 1/2 2
29 10157 NUT, HEX NYLON JAM 1/2-13 1
30 10055 SCREW, CAP 3/8-16 x 1 2
31 10811 WASHER, LOCK 3/8 2
32 10025 WASHER, FLAT 3/8 2
33 64003 LOCK, HOOD 2
34 11522 WASHER, SERRATED BELLEVILLE .489” ID 2
35 64406 RUBBER SEAL, REAR 1
36 64405 RETAINING BRKT., REAR SEAL 1
37 10031 SCREW, CAP 1/4-20 X 1 4
38 10602 WASHER, FLAT 1/4 4
39 10150 NUT, HEX NYLON LOCK 1/4-20 4
40 64402A HOOD SUBASSEMBLY (INCLUDES ITEMS 41-47) 1
41 64402 HOOD ONLY 1
42 64030 PLUG, CAP 3" TUBE 1
43 64404 RUBBER SEAL, FRONT 1
44 64403 RETAINING BRKT., FRONT SEAL 1
45 10150 NUT, HEX NYLON LOCK 1/4-20 7
46 10602 WASHER, FLAT 1/4 7
47 10031 SCREW, CAP 1/4-20 X 1 7
-- 64407 RUBBER SEAL W/ BRKT. (INCLUDES ITEMS 48 & 49) 1
48 64408 RETAINING BRKT., SIDE SEAL 2
49 64409 RUBBER SEAL, SIDE 2
50 11643 RIVET, BLIND 3/16"DIA 4
51 10816 SCREW, CAP 3/8-24 X 1-1/2 (SEE ILLUS. 9, ITEM 4) -
52 10025 WASHER, FLAT 3/8 SAE (SEE ILLUS. 9, ITEM 5) -
53 10152 NUT, HEX NYLON LOCK 3/8-24 (SEE ILLUS. 9, ITEM 6) -
PARTS LISTING - ILLUSTRATION 1: FRAME GROUPING

Printed in USA
©2006
Page 6
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 2:LIFTING SYSTEM GROUPING
15
16
17
OPTIONAL
10
3
22
28
30
30
20
18
17
16
14
13
12
41
27
33
40
37
46
45
45
44
43
42
39
38
1
4
34
34
33
31
31
32
32
27
25
26
26
25
36
35 24
23
29
21
19
11
9
8
7
6
5
2

Printed in USA
©2006
Page 7
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
PARTS LISTING - ILLUSTRATION 2: LIFTING SYSTEM GROUPING
ITEM# PART# DESCRIPTION QTY.
1 64011A HANDWHEEL SUBASSEMBLY (INCLUDES ITEMS 2-11) 1
2 64011 HANDWHEEL, SMALL W/ 5/8-8 x 20” ROD 1
3 80007 DECAL, CUT CONTROL DN-UP(SMALL ROUND) 1
4 14023 KNOB, BALL 1-3/8”DIA. W/1/2-13 THREADS 1
5 50550 SLEEVE FOR 1/2” CAPSCREW, TAPERED 1
6 10411 SCREW, SOCKET HEAD CAP 1/2-13 x 4 1
7 85005 BEARING, BALL 5/8”ID x 1-1/2” OD THRUST 1
8 64013 LINKAGE, UPPER SUPPORT 1
9 10440 COLLAR, LOCKING 7/8” ID 1
10 10073 WASHER, FLAT 5/8 1
11 10096 COLLAR, LOCKING 5/8” ID 1
12 10326 SCREW, CAP 5/8-11 x 3 1
13 10073 WASHER, FLAT 5/8 2
14 79035 BUSHING, RUBBER 1-1/16”OD x 5/8”ID x 1/4” THK. 1
15 14023 KNOB, BALL 1-3/8”DIA. W/1/2-13 THD. 1
16 10308 SCREW, CAP 1/2-20 x 1-1/2 2
17 10154 NUT, HEX NYLON LOCK 1/2-20 2
18 10808 FITTING, GREASE 1/4-28 STRAIGHT 1
19 10784 CLAMP, HOSE SIZE 20, ADJ. TO 1-3/4” 2
20 10930 BELLOWS-1-1/4” ID x 2-3/8”E.L. x 1-3/4”R.L. 1
21 64012 LINKAGE, LOWER CONTROL 18”L 1
22 10808 FITTING, GREASE 1/4-28 STRAIGHT 1
23 10347 SSCREW, CAP 1/2-20 X 2-1/4 1
24 10154 NUT, HEX NYLON LOCK 1/2-20 1
25 10003 SCREW, CAP 7/16-20 x 1-1/4” 4
26 10062 WASHER, FLAT 7/16 4
27 10153 NUT, HEX NYLON 7/16-20 4
28 64006A FORK SUBASSEMBLY (INCLUDES ITEMS 29-36) 1
29 64006 FORK 1
30 62022 BEARING, BALL 1” 2-HOLE FLANGE 2
31 64031 SPACER, WHEEL 3/4” ID x 1”L 2
32 80028 WHEEL 6 x 2 x 3/4” BEARING 2
33 10009 WASHER, FLAT 3/4 2
34 10306 PIN, COTTER 3/16 x 1-1/4 2
35 10373 BOLT, TAP 1/2-13 x 5(FULL THREAD) 1
36 10417 NUT 1/2-13 1
37 64450 OUTRIGGER WHEELASSEMBLY COMPLETE (INCLUDES ITEMS 38-46) 1
38 64451 OUTRIGGER FORK 1
39 10961 FITTING, GREASE 1/4-28 x 90° 2
40 10003 SCREW, CAP 7/16-20 x 1-1/4 4
41 10062 WASHER, FLAT 7/16 4
42 10153 NUT, HEX NYLON LOCK 7/16-20 4
43 10932 WHEEL 4 x 1-1/2 x 3/8” BRG., POLY TREAD 2
44 10815 SCREW, CAP 3/8-24 x 2-3/4 2
45 10025 WASHER, FLAT 3/8 6
46 10004 NUT, LOCK 3/8-24 2

Printed in USA
©2006
Page 8
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 3: TRANSMISSION GROUPING
1
27
16
15
14
53
49
34
52
51
50
49
49
48
47
46 45 44
43
42
41
35 37A
40
38
36
39
37
35
40
34
20
30
29
29
28
31 32
29 33
21
25
24
26
26
23
23
22
21
20
19
18
17
13
12
11
10
9
1
6
5
2
3
3
34
7
8

Printed in USA
©2006
Page 9
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
PARTS LISTING - ILLUSTRATION 3: TRANSMISSION GROUPING
ITEM# PART# DESCRIPTION QTY.
1 50061A TRANSMISSION SUBASSEMBLY (INCLUDES ITEMS 2-8) 1
2 50061 TRANSMISSION, HYDROSTATIC 1
3 50071 KEY, WOODRUFF 1/8 x 1/2(#404) 3
4 50048 SPROCKET #3511 x .67” BORE 1
5 50062 SHEAVE, HYD. TRANS. 4”OD x 1Gr. x .671”B 1
6 64022 TRANSMISSION CONTROLARM 1
7 10811 WASHER, LOCK 3/8 1
8 10404 NUT 3/8-16 1
9 10909 BOLT, CARRIAGE 3/8-16 x 3 4
10 10040 WASHER, GARRET 1”OD x 17/32”ID x .054”T 4
11 64018 MOUNT, TRANSMISSION 1
12 10811 WASHER, LOCK 3/8 4
13 10404 NUT 3/8-16 4
14 10055 SCREW, CAP 3/8-16 x 1 4
15 10811 WASHER, LOCK 3/8 4
16 10025 WASHER, FLAT 3/8 4
17 10018 SCREW, CAP 1/4-20 x 3/4 1
18 10038 WASHER, LOCK 1/4 1
19 50266 FAN BLADE W/ PLATE 7”, TRANSMISSION 1
20 10152 NUT, HEX NYLON LOCK 3/8-24 2
21 10011 SPACER, STEEL 5/8”OD x 3/8”ID x 3/8 2
22 64024A LINKAGE SUBASSY., DRIVE HORIZ.(INCLUDES ITEMS 23-25) 1
23 10919 ROD END, FEMALE 3/8-24 R.H. THREADS 2
24 10014 NUT 3/8-24 1
25 64024 ROD, ALL THREAD 3/8-24 x 2”L 1
26 10816 SCREW, CAP 3/8-24 x 1-1/2 2
27 64021 BELL CRANK, DRIVE LINKAGE 1
28 10322 SCREW, CAP 1/2-20 x 2 1
29 10312 WASHER, FLAT 1/2 5
30 10045 WASHER, LOCK 1/2 1
31 10417 NUT 1/2-13 1
32 10040 WASHER, GARRET 1”OD x 17/32”ID x .054”T 1
33 10154 NUT, HEX NYLON LOCK 1/2-20 1
34 10152 NUT, HEX NYLON LOCK 3/8-24 2
35 10011 SPACER, STEEL 5/8”OD x 3/8”ID x 3/8” 2
36 64023A LINKAGE SUBASSY., DRIVE VERT. (INCLUDES ITEMS 37-39) 1
37 10919L ROD END, FEMALE 3/8-24 L.H. THREAD 1
37A 10919 ROD END, FEMALE 3/8-24 R.H. THREAD 1
38 10014 NUT 3/8-24 1
39 64023 LINKAGE, ROD 3/8 x 14-1/4”L 1
40 10816 SCREW, CAP 3/8-24 x 1-1/2 2
41 64020 LEVER, DRIVE 1
42 10920 KNOB, BALL 1-3/8”DIA. W/ 5/16-24 THD. 1
43 10314 SCREW, CAP 1/4-20 x 1-3/4 1
44 10602 WASHER, FLAT 1/4 1
45 50074 SPRING, EXT. 1”OD x 3-15/16” INSIDE ENDS 1
46 10015 NUT, LOCK 1/4-20 1
47 10150 NUT, HEX NYLON LOCK1/4-20 1
48 10322 SCREW, CAP 1/2-20 x 2 1
49 10312 WASHER, FLAT 1/2 4
50 10045 WASHER, LOCK 1/2 1
51 10417 NUT 1/2-13 1
52 10040 WASHER, GARRET 1”OD x 17/32”ID x .054”T 1
53 10154 NUT, HEX NYLON LOCK 1/2-20 1

Printed in USA
©2006
Page 10
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 4: CLUTCH & REAR AXLE GROUPING
25
24
48
16
60
18
63
62
61
64
65
66
67
68
68
68
69
70
64
65
66 63
62
61
73
72
72
71
45
43 42
40
39
41
51
46
47
50
49
49 33
59
58
57
56
55
54
53
52
37
36
35
34
33
32
31
24
23
22
21
28
29
30
26
20 21
27
20
19
15
17
15
14
13
12
11
10
9
8
7
7
6
5
4
3
2
1
38

Printed in USA
©2006
Page 11
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
PARTS LISTING - ILLUSTRATION 4: CLUTCH & REAR AXLE GROUPING
ITEM# PART# DESCRIPTION QTY.
1 14023 KNOB, BALL 1-3/8”DIA. W/1/2-13 THD. 1
2 64025 LEVER, CLUTCH 1
3 10150 NUT, HEX NYLON LOCK 1/4-20 1
4 10905 SCREW, CAP 1/4-20 x 1-1/4 1
5 10433 WASHER, BELLEVILLE SPRING 1/2”ID x 3/32” 1
6 10921 SPRING, COMP. .72”OD x 1.25”FL x .08”WD 2
7 57126A CLUTCH LINKAGE SUBASSEMBLY 1
(INCLUDES ITEMS 8-18)
8 57126 LINKAGE, CLUTCH 19-1/4”L 1
9 10024 PIN, ROLL 1/4 x 1-1/4 1
10 64082 BRACKET, SAFETY SWITCH 1
11 57151 BRACKET, CLUTCH LINKAGE LOCK 1
12 10014 NUT 3/8-24 1
13 3605 ROD END, MALE 3/8-24 1
14 10997 BOOT, RED RUBBER, STOP SWITCH 1
15 10312 WASHER, FLAT 1/2 2
16 10992 SWITCH,PUSH BUTTON, 1PST N.O., MOMENT. 1
17 10887 SWITCH,PUSH BUTTON, 1PST N.C., MOMENT. 1
18 10674 BOOT, TOGGLE SWITCH 1
19 10408 SCREW, CAP 1/2-13 x 9 1
20 10312 WASHER, FLAT 1/2 2
21 64026A BELLCRANK SUBASSEMBLY, CLUTCH 1
(INCLUDES ITEMS 22-25)
22 64026 BELL CRANK, CLUTCH 1
23 10924 CAM FOLLOWER BRG. 3/4 x 3/8-24 THD. 1
24 10025 WASHER, FLAT 3/8 2
25 10152 NUT, HEX NYLON LOCK 3/8-24 1
26 10155 NUT, HEX NYLON LOCK 1/2-13 1
27 10030 SCREW, CAP 3/8-24 x 2 1
28 10011 SPACER, STEEL 5/8”OD x 3/8”ID x 3/8” 1
29 10025 WASHER, FLAT 3/8 2
30 10152 NUT, HEX NYLON LOCK 3/8-24 1
31 64027A CLUTCH & JACKSHAFT SUBASSEMBLY 1
(INCLUDES ITEMS 32-50)
32 50436 SPROCKET #40B10 x 3/4” BORE 1
33 50049 BEARING, BALL 3/4” 2-HOLE FLANGE 2
34 50523 KEY 3/16”SQ. x 1-1/8”L 1
35 10307 KEY 1/4”SQ. x 2-1/4”L 1
36 64027 JACKSHAFT, CLUTCH 10-1/2”L 1
37 10009 WASHER, FLAT 3/4 1
38 57038A BEARING & CARRIER ASSEMBLY, CLUTCH 1
(INCLUDES ITEMS 39 & 40)
ITEM# PART# DESCRIPTION QTY.
39 57038 BEARING, BALL 3/4”ID x 1.8504”OD 1
40 57039 CARRIER, CLUTCH BEARING 1
41 50476 SPROCKET, CLUTCH #35A60 1
42 10354 SCREW, SKT. HEAD CAP 3/8-24 x 1-3/4 2
43 10113 SPACER, STEEL 9/16”OD x 3/8”ID x 7/32” 2
45 10152 NUT, HEX NYLON LOCK 3/8-24 2
46 50477 CLUTCH, DOG, SUBASSEMBLY 1
* 57042 CLUTCH, DOG BLOCK 1
* 3695 SEAL, OIL .750 x 1.375 x .250 1
* 10808 FITTING, GREASE 1/4-28 STRAIGHT 1
47 57044 CLUTCH, SPRING CUP 1
48 10922 SPRING, COMP. 1”OD x 3.75”FL x .105”WD 1
49 10768 CLAMP, HOSE, SAE #16, ADJ. TO 1-1/2” 2
50 10930 BELLOWS: 1-1/4”ID x 2-3/8”E.L. x 1-3/4”R.L. 1
51 64032 CHAIN #35 x 24-1/2” L.O.A. 1
(INCLUDES #35 CONNECTING LINK)
52 10055 SCREW, CAP 3/8-16 x 1 2
53 10811 WASHER, LOCK 3/8 2
54 10025 WASHER, FLAT 3/8 2
55 50509 MOUNT, JACKSHAFT BEARING 1
56 10309 SCREW, CAP 3/8-24 x 1-1/4 4
57 10025 WASHER, FLAT 3/8 4
58 10811 WASHER, LOCK 3/8 4
59 10014 NUT 3/8-24 4
60 64028A AXLE & WHEEL SUBASSEMBLY 1
(INCLUDES ITEMS 61-69)
61 10914 SCREW, CAP 1/2-13 x 1 2
62 10045 WASHER, LOCK 1/2 2
63 10433 WASHER, BELLEVILLE SPRING 1/2”ID x 3/32 2
64 50098 WHEEL 8 x 2 x 1” BORE 2
65 10906 RETAINING RING, EXT. 1” 2
66 62022 BEARING, BALL 1” 2-HOLE FLANGE 2
67 64028 AXLE SHAFT 1”RD x 20-3/8”L 1
68 10307 KEY 1/4”SQ. x 2-1/4”L 3
69 61126 SPROCKET #40B34 x 1”BORE 1
70 64033 CHAIN #40 x 25-3/4”L 1
(INCLUDES #40 OFFSET & CONNECTING LINKS)
71 10003 SCREW, CAP 7/16-20 x 1-1/4 4
72 10062 WASHER, FLAT 7/16 8
73 10153 NUT, HEX NYLON LOCK 7/16-20 4

Printed in USA
©2006
Page 12
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
21
21
20
19
26
17
13
12
11
10
9
16
15
14
8
7
6
5
5
3
2
1
25
18
26
27
23
22
24
4
20
47
46
31
28
42
46
38
INCLUDED WITH HONDA ENGINE.
AIR CLEANER ASSEMBLY PLUS HOSE
*
45
44
43
49
50
48
41
40
39
37
33 34
32
30
29
35
36
ILLUSTRATION 5: HONDA ENGINE GROUPING FOR 20HP UNITS

Printed in USA
©2006
Page 13
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ITEM# PART# DESCRIPTION QTY.
1 15056A ENGINE SUBASSY., HONDA 20HP 1
(INCLUDES ITEMS 2-13)
2 15056 ENGINE, HONDA 20HP GX620-K1TZF2 1
3 15168 MUFFLER, HONDA VHRM3 1
4 11533 FITTING, ADAPTER 6-M14 x 1.5 TO 1/4-18 NPT 1
5 11579 BARB, PUSH ON, 1/2 HOSE x 1/4 MPT 2
6 64057 HOSE, PUSH ON, 1/2ID x 10-1/2”L 1
7 57159 BRACKET, OIL DRAIN 1
8 50552 PIPE PLUG, 1/2 NPT (BRASS) 1
9 10087 BOLT, CARRIAGE 3/8-16 x 1-3/4 2
10 10040 WASHER, GARRET 1”OD x 17/32”ID x .054”T 4
11 51014 MOUNT BRACKET, CHANNEL 2
12 10811 WASHER, LOCK 3/8 2
13 10404 NUT 3/8-16 2
14 10018 SCREW, CAP 1/4-20 x 3/4 2
15 10038 WASHER, LOCK 1/4 2
16 10602 WASHER, FLAT 1/4 2
17 10335 BOLT, CARRIAGE 3/8-16 x 2-1/2 2
18 10804 BOLT, CARRIAGE 3/8-16 x 1-1/2 2
19 64017 MOUNT, ENGINE 1
20 10811 WASHER, LOCK 3/8 4
21 10404 NUT 3/8-16 4
22 10321 SCREW, CAP 1/2-20 X 1-1/4 2
23 10312 WASHER, FLAT 1/2 SAE 2
24 10154 NUT, HEX NYLON LOCK 1/2-20 2
25 10309 SCREW, CAP 3/8-24 X 1-1/4 PLATED 2
26 10025 WASHER, FLAT 3/8 SAE 4
27 10152 NUT, HEX NYLON LOCK 3/8-24 2
PARTS LISTING-ILLUSTRATION 5: HONDA ENGINE GROUPING FOR 20HP UNITS
ITEM# PART# DESCRIPTION QTY.
28 51081 CABLE, TURN-TO-LOCK CONTROL 72” 1
(CUT TO LENGTH 54”)
29 10846 SCREW, SELF-TAP HEX WASHER 1/4-20x1/2 2
30 15129 CABLE, CHOKE 72” 1
(CUT TO LENGTH 58”)
31 15138 METER, HOUR REDINGTON INDUCTIVE 1
32 84011 BATTERY, 12 VOLT/300 C.C.A. 1
33 10156 NUT, HEX NYLON LOCK 3/8-16 2
34 64008 CLAMP, BATTERY HOLD DOWN 1
35 64049 RUBBER PAD 2-1/2”L x 1-1/2”W x 1/8 THICK 1
36 50117B CABLE, EYE TO EYE, 4 GA. x 24” (BLACK) 1
37 50117R CABLE, EYE-EYE 4GA. X 24" (RED) 1
38 11583 INSULATOR, BATTERY TERMINAL 1
U-1 STYLE RED L.H.
39 10818 BOLT, CARRIAGE 5/16-18 x 3/4 2
40 10801 WASHER, LOCK 5/16 2
41 10054 NUT 5/16-18 2
42 64014A GAS TANK SUBASSEMBLY 1
(INCLUDES ITEMS 43-45)
43 64014 TANK, GAS (INCLUDES CAP, ITEM 45) 1
44 61058 TUBE, FUEL PICK UP 19” 1
45 61056 CAP, GAS TANK 1
46 10762 CLAMP, HOSE-SPRING TYPE 3/8” GREEN 2
47 64035 HOSE, FUEL 1/4” ID x 50” 1
48 10053 SCREW, CAP 5/16-18 x 3/4 3
49 10801 WASHER, LOCK 5/16 3
50 10213 WASHER, FLAT 5/16 3

Printed in USA
©2006
Page 14
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 6: ENGINE GROUPING FOR 12HP & 13HP UNITS
9
OIL DRAIN
TO ENGINE
28
27
26
25
24
26
25
24
20
18
17
6
5
4
3
1
12 13
14
11
10
8
7
19
22
21
16 15
29
30
31
32
23
2
33
OPTIONAL

Printed in USA
©2006
Page 15
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
PARTS LISTING-ILLUSTRATION 6: ENGINE GROUPING FOR 12HP & 13HP UNITS
ITEM# PART# DESCRIPTION QTY.
1 15029A ENGINE SUBASSEMBLY, HONDA 13HP(SHOWN) 1
(INCLUDES ITEMS 2-11)
15045A ENGINE SUBASSEMBLY, KOHLER 12HP
(INCLUDES ITEMS 2-11)
2 ENGINE 1
15029 HONDA 13HP GX390K1-QXC9 (SHOWN)
15045 KOHLER 12HP COMMAND PRO CS12T
3 10804 BOLT, CARRIAGE 3/8-16 x 1-1/2 2
4 51014 MOUNT BRACKET, CHANNEL 2
5 10025 WASHER, FLAT 3/8 2
6 10404 NUT 3/8-16 2
7 11542 BARB, PUSH ON 3/8”ID x 12mm x 1.50 MALE 1
8 64068 HOSE, PUSH ON 3/8”ID x 12”L 1
9 11580 BARB, PUSH ON 3/8”ID x 1/2MPT 1
10 57159 BRACKET, OIL DRAIN 1
11 50552 PIPE PLUG, 1/2 NPT 1
12 10018 SCREW, CAP 1/4-20 x 3/4 2
13 10038 WASHER, LOCK 1/4 2
14 10602 WASHER, FLAT 1/4 2
15 10321 SCREW, CAP 1/2-20 x 1-1/4 2
16 10312 WASHER, FLAT 1/2 2
17 64017 MOUNT, ENGINE 1
18 10154 NUT, HEX NYLON LOCK 1/2-20 2
19 10309 SCREW, CAP 3/8-24 x 1-1/4 2
20 10025 WASHER, FLAT 3/8 4
21 10152 NUT, HEX NYLON LOCK 3/8-24 2
22 10908 BOLT, CARRIAGE 3/8-16 x 2-1/2 2
23 10804 BOLT, CARRIAGE 3/8-16 x 1-1/2 4
24 10025 WASHER, FLAT 3/8 4
25 10811 WASHER, LOCK 3/8 4
26 10404 NUT 3/8-16 4
27 10340 BOLT, TAP 1/2-13 x 3(FULL THREAD) 1
28 10417 NUT 1/2-13 1
29 64066 GRILL, REAR 1
30 10806 SCREW, CAP 5/16-18 x 1 3
31 10801 WASHER, LOCK 5/16 3
32 10213 WASHER, FLAT 5/16 3
33 15138 METER, HOUR, REDINGTON INDUCTIVE (OPTIONAL) 1

Printed in USA
©2006
Page 16
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 7: ELECTRIC MOTOR GROUPING
47
42
41
46
47
48
18
48
47
52
51
50 49
50
57
56
54
49 48
46
19 59
60
20
64
63
62
61
58
50
53 47 48 50
28
30
31
21
22
23
24
25
26
44
45
27
38
37
36
35
41
41
40
39
43
42
32
33
34
29
55
AC INPUT
17
16
15
13
14
13
12
11
10
9
6
5
4
3
7
8
4
3
6
5
4
3
22
1
TO SAFETY SWITCHES

Printed in USA
©2006
Page 17
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ITEM# PART# DESCRIPTION QTY.
1 16004 MOTOR, BALDOR 10HP-3PH 60HZ 3450RPM 1
2 64061 MOUNT BRKT., 10 HP BALDOR 2
3 10404 NUT 3/8-16 6
4 10811 WASHER, LOCK 3/8 6
5 10417 NUT 1/2-13 4
6 10804 BOLT, CARRIAGE 3/8-16 X 1-1/2 F.T. 4
7 10802 BOLT, CARRIAGE 3/8-16 X 1 FULL THD. 2
8 10040 WASHER, GARRET 17/32 X 1 X .054 2
9 64017 MOUNT, ENGINE/MOTOR 1
10 10340 BOLT, TAP 1/2-13 X 3 (FULL THREAD) 1
11 10417 NUT 1/2-13 1
12 10309 SCREW, CAP 3/8-24 X 1-1/4 PLATED 2
13 10025 WASHER, FLAT 3/8 SAE 4
14 10152 NUT, HEX NYLON LOCK 3/8-24 2
15 10321 SCREW, CAP 1/2-20 X 1-1/4 2
16 10312 WASHER, FLAT 1/2 SAE 2
17 10154 NUT, HEX NYLON LOCK 1/2-20 2
18 64412 WIRE HARNESS 10/4 X 66" 1
19 16172 STRAIN RELIEF 1"NPT X .625-.750" 1
20 10770 CONDUIT LOCK NUT 1" NP 1
21 64413 WIRE HARNESS 10/4 X 50" 1
22 41122 TREADLE, TRANSFER ARM 1
23 10150 NUT, HEX NYLON LOCK 1/4-20 1
24 10984 CONN., LIQUID TITE 90D X 3/4NPT 2
25 10740 CONDUIT LOCK NUT 3/4 NP 2
26 16450 STARTER 11-M2-BRF-P32-33-02460 (230V) 1
16447 STARTER 11-M2-BRF-P32-15-02460 (460V) 1
27 64411 BRACKET, LOVATO STARTER 1
28 10362 SCREW, MACHINE 8-32 X 3/4 4
29 10875 WASHER, FLAT #8 SAE 4
30 10461 WASHER, LOCK, INT. TOOTH #8 4
31 10462 NUT 8-32 8
32 10053 SCREW, CAP 5/16-18 X 3/4 2
33 10213 WASHER, FLAT 5/16 SAE 4
34 10807 NUT, LOCK 5/16-18 2
35 10018 SCREW, CAP 1/4-20 X 3/4 1
PARTS LISTING-ILLUSTRATION 7: ELECTRIC MOTOR GROUPING
ITEM# PART# DESCRIPTION QTY.
36 10602 WASHER, FLAT 1/4 SAE 2
37 11566 CLAMP, LOOM, 1-3/4" (SAE SIZE 28) 1
38 10150 NUT, HEX NYLON LOCK 1/4-20 1
39 64414 WIRE HARNESS 16/3 X 40" 1
40 40066 STRAIN RELIEF 1/2NPT X .350-.450" 1
41 10790 CONDUIT LOCK NUT 1/2 NP 3
42 41130 STRAIN RELIEF 1/2NPT X .550-.650" 2
43 64415 WIRE HARNESS 16/5 X 48" 1
44 16500 TRANFORMER W/ BOX COMPLETE 1
REPLACEMENT PARTS INCLUDE:
16150 TRANSFORMER 75VA 240/480P.V.-24S.V. 1
16501 ENCLOSURE, NEMA 4X, 6.9 X 6.9 X 5.9 1
16502 ENCLOSURE PANEL 5.8 X 5.8 1
16504 FUSE, MIDGET 600VAC, 5 AMP 1
16505 FUSE BLOCK, SINGLE POLE W/ BOX LUGS 1
16506 SCREW, SHEET METAL 8 X 3/8 TRUSS HD 12
45 64062 SHROUD, MOTOR 1
46 10905 SCREW, CAP 1/4-20 X 1-1/4 4
47 10038 WASHER, LOCK 1/4 6
48 10602 WASHER, FLAT 1/4 SAE 6
49 52045 SPACER, STEEL 5/8OD X 3/8ID X 3/4L 4
50 10439 THREAD-SERT 1/4-20, BLIND RIVET 6
51 10011P SPACER,PLTD.STL.5/8OD X 3/8ID X 3/8 1
52 10031 SCREW, CAP 1/4-20 X 1 1
53 10018 SCREW, CAP 1/4-20 X 3/4 1
54 10362 SCREW, MACHINE 8-32 X 3/4 4
55 10875 WASHER, FLAT #8 SAE 4
56 10461 WASHER, LOCK, INT. TOOTH #8 4
57 10462 NUT 8-32 8
58 64063 SHROUD SIDE PANEL, MOTOR 1
59 10846 SCREW, CAP STSHW 1/4-20 X 1/2 2
60 10038 WASHER, LOCK 1/4 2
61 64066 GRILLE, REAR 1
62 10213 WASHER, FLAT 5/16 SAE 3
63 10801 WASHER, LOCK 5/16 3
64 10806 SCREW, CAP 5/16-18 X 1 3

Printed in USA
©2006
Page 18
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 8: BELT DRIVE GROUPING
1
17 16
21
11
5
2
3
4
6
7
8
9
10
12
13
14
18
19
20
22
15

Printed in USA
©2006
Page 19
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ITEM# PART# DESCRIPTION QTY.
1 64019A IDLER ARM SUBASSEMBLY (INCLUDES ITEMS 2-6) 1
2 64019 BRACKET, IDLER 1
3 10029 SCREW, CAP 3/8-24 X 1-3/4 1
4 10113 SPACER, STEEL 9/16” OD x 3/8” ID x 7/32”T 1
5 50115 PULLEY, IDLER 3”OD x 1GR.AB x 3/8” BRG. 1
6 10152 NUT, HEX NYLON LOCK 3/8-24 1
7 50074 SPRING, EXT. 1”OD x 3-15/16” INSIDE ENDS 1
8 10312 WASHER, FLAT 1/2 1
9 10155 NUT, HEX NYLON LOCK 1/2-13 1
10 10025 WASHER, FLAT 3/8 1
11 10156 NUT, HEX NYLON LOCK 3/8-16 1
12 10528 SHEAVE, 4.15”OD x 1GR.AB x TAPER LOCK 1
13 10305 KEY 1/4” SQUARE x 1-1/4”L 1
14 BUSHING, SHEAVE TAPER LOCK 1
10529A 1-1/8” WITH COUNTERBORE (20HP HONDA)
10544 1” BORE (13HP HONDA)
10529 1-1/8” BORE (12HP KOHLER)
10537 1-3/8” BORE (10HP BALDOR)
15 BELT 1
10218 4L-450 (HONDA, 12HP KOHLER COMMAND, BALDOR)
10240 AP-44(20HP KOHLER COMMAND)
16 BUSHING, SHEAVE JA 1
10533 1-1/8” BORE (20HP HONDA)
10557 1” BORE (13HP HONDA)
10533 1-1/8” BORE (12HP KOHLER)
* NO BUSHING FOR 10HP BALDOR
17 10118 KEY, 3/8”SQ. x 2-1/4 1
18 SHEAVE 1
64037 2.8”OD x 4Gr.3V x JA (13/20HP HONDA & 12HP KOHLER)
64069 3”OD x 4 Gr.3V x 1-3/8” BORE (10HP BALDOR)
19 64038 SHEAVE 4.75”OD x 4GR. 3V x SDS 1
20 10305 KEY 1/4” SQ. x 1-1/4” L 1
21 10064 BUSHING, SHEAVE SDS x 1-1/4” BORE 1
22 10235 BELT 3VX-475 4
PARTS LISTING-ILLUSTRATION 8: BELT DRIVE GROUPING

Printed in USA
©2006
Page 20
E-CPU10FC-PL-0206
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone [phone] • 1-800-638-3326
Fax [phone] • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]
ILLUSTRATION 9: DRUM BEARING & AXLE GROUPING
ITEM# PART# DESCRIPTION QTY.
1 64410 SPINDLE SHAFT 24" 1
2 64162 PIN, DOWEL 1/4 x 5/8(.002 OVERSIZED) 1
3 84082R BEARING, ROLLER 1-1/4 PILOT 4-HOLE 1
NOTE: SET SCREW COLLAR REMOVED
4 10816 SCREW, CAP 3/8-24 x 1-1/2 8
5 10025 WASHER, FLAT 3/8 12
6 10152 NUT, HEX NYLON LOCK 3/8-24 8
7 CUTTER WHEEL DRUM ASSEMBLY COMPLETE 1
64420 4 SHAFT CUTTER DRUM (REFER TO ILLUS. 10)
64430 6 SHAFT CUTTER DRUM (REFER TO ILLUS. 11)
8 64160 BEARING & DRIVER ASSEMBLY COMPLETE 1
A 10490 SCREW, SOCKET HEAD CAP 1/2-13 x 1 3
B 64155B HUB WITH SHAFT, DRIVE 1
C 64154 RETAINING RING, INTERNAL 2-3/16” 2
D 64152 BEARING, ROLLER 35mm x 72mm x 23mm 2
E 64153 SPACER, BEARING CENTER 1
F 64151 HOUSING, BEARING 1
G 10953 FITTING, GREASE 1/8 NPT STRAIGHT 1
9 64159 SHIM 3/8”ID x 5/8”OD x .031”THK. (USE WHEN REQ’D) 2
10 10445 NUT, JAM 7/8-9 LEFT HAND THREAD 2
11 64158 WASHER, INT. TOOTH 7/8 1
G
C
D
FE
D
C
B
A
8
7
6
11
10
5
9
4
8
2
1
6
5
5
4
3