Edco CPU12-35K Datasheet

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 1
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LIST MANUAL
MODEL CPU12-35K
REVISED STARTING
SERIAL # 170410128
12” SELF-PROPELLED SCARIFIER
SKU # MODEL # POWER OPTION
75700 CPU12-35K KOHLER 35HP GASOLINE ENGINE MODEL CH980

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 2
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY
BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly.
Extreme care must be taken when operating electric
models with water present: Ensure power cord is prop-
erly grounded, is attached to a Ground-Fault-Interrupter
(GFI) outlet, and is undamaged.
•Check all electrical cables - be sure connections are tight and
cable is continuous and in good condition. Be sure cable is
correctly rated for both the operating current and voltage of
this equipment.
•Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with qualied electri-
cian or service person if there is any doubt as to whether the
outlet is properly grounded. Adhere to all local codes and
ordinances.
•NOTE: In the event of a malfunction or breakdown, grounding
provides a path of least resistance for the electric current to
dissipate. The motor is equipped with a grounded plug and
must be connected to an outlet that is properly installed and
properly grounded. DO NOT modify the plug provided on the
motor. If the plug does not t the outlet have a qualied electri-
cian install the proper receptacle.
•Switch motor OFF before disconnecting power.
•Engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects or other reproduc-
tive harm.
• Gasoline is extremely ammable and poisonous.
It should only be dispensed in well ventilated areas,
and with a cool engine.
•Small gasoline engines produce high concentra-
tions of carbon monoxide (CO) example: a 5 HP 4 cycle
engine operation in an enclosed 100,000 cu. ft. area with
only one change of air per hour is capable of providing
deadly concentrations of CO in less than fteen minutes.
Five changes of air in the same area will produce noxious
fumes in less than 30 minutes. Gasoline or propane pow-
ered equipment should not be used in enclosed or partially
enclosed areas. Symptoms of CO poisoning include, head-
ache, nausea, weakness, dizziness, visual problems and
loss of consciousness. If symptoms occur - get into fresh
air and seek medical attention immediately.
SAFETY
MESSAGES
SAFETY MESSAGES
Indicates an imminent hazard which, if not
avoided, will result in death or serious injury.
Indicates an imminent hazard which, if not
avoided, can result in death or serious injury.
Indicates hazards which, if not avoided, could
result in serious injury and or damage to the
equipment.
•Safety Instructions are proceeded by a graphic alert symbol
of DANGER, WARNING, or CAUTION.
ELECTRICAL POWERED EQUIPMENT
GASOLINE/PROPANE POWERED EQUIPMENT
•Equipment should only be operated by trained personnel in
good physical condition and mental health (not fatigued). The
operator and maintenance personnel must be physically able
to handle the bulk weight and power of this equipment.
•This is a one person tool. Maintain a safe operating distance
to other personnel. It is the operators’ responsibility to keep
other people (workers, pedestrians, bystanders, etc.) away
during operation. Block off the work area in all directions with
roping, safety netting, etc. for a safe distance. Failure to do so
may result in others being injured by ying debris or exposing
them to harmful dust and noise.
•This equipment is intended for commercial use only.
•For the operator’s safety and the safety of others, always keep
all guards in place during operation.
•Never let equipment run unattended.
•Personal Protection Equipment and proper safety attire must
be worn when operating this machinery. The operator must
wear approved safety equipment appropriate for the job such
as hard hat and safety shoes when conditions require. Hear-
ing protection MUST be used (operational noise levels of this
equipment may exceed 85db). Eye protection MUST be worn
at all times.
Keep body parts and loose clothing away from moving
parts. Failure to do so could result in dismemberment
or death.
•Do not modify the machine.
•Stop motor/engine when adjusting or servicing this equipment.
Maintain a safe operating distance from ammable
materials. Sparks from the cutting-action of this machine
can ignite ammable materials or vapors.
GENERAL INSTRUCTIONS
DUST WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activi-
ties contains chemicals known to cause cancer,
birth defects, or other reproductive harm. Some
examples of these chemicals are:
•Lead from lead-based paints, and
•Crystalline silica from bricks and concrete and other
masonry products.
Your risk of exposure to these chemicals varies depending
on how often you do this type of work. To reduce your risk:
work in a well ventilated area, use a dust control system, such
as an industrial-style vacuum, and wear approved personal
safety equipment, such as a dust/particle respirator designed
to lter out microscopic particles.
•Do not disconnect power by pulling cord. To disconnect, grasp
the plug, not the cord.
•Unplug power cord at the machine when not in use and before
servicing.

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 3
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LIST MANUAL
MODEL CPU12-35K
12” SELF-PROPELLED SCARIFIER
Section Page Number
Safety Messages and General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Illustration 1: Frame & Console Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5
Illustration 2: Lifting System Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7
Illustration 3: Hydraulic Pump Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9
Illustration 4: Rear Axle & Jackshaft Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11
Illustration 5: Transmission, Drive Lever & Linkage Grouping. . . . . . . . . . . . . . . . . . 12, 13
Illustration 6: 5th Wheel Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15
Illustration 7: Water Valve & Hose Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Illustration 8: Lifting Bail Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Illustration 9: Bearing Grouping for Cutter Drum . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Illustration 10: Cutter Drum Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Illustration 11: Engine & Mount Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 21
Illustration 12: Battery Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Illustration 13: Instrument Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Illustration 14: Idler Arm Grouping for Transmission Belt . . . . . . . . . . . . . . . . . . . . . 24
Illustration 15: Belt Drive Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Illustration 16: Belt Cover Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 27
Illustration 17: Fuel Tank Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29
Illustration 18: Optional Vacuum Hood Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Decal Sheets 1 & 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 33
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Limited Equipment Warranty of Sale - Terms & Conditions . . . . . . . . . . . . . . . . . . . 36 (Back Page)
HOW TO ORDER REPLACEMENT PARTS
 To insure product safety and reliability, always use
genuine EDCO replacement parts when making
repairs to the equipment.
 When calling for parts, specify the MODEL and
SERIAL number of the machine, which can be found
on the NAME PLATE. Keep that information in the
space provided. In addition to this information, give
part number, description, and quantity as listed on
the parts list to your parts representative.
 Please note: Due to improvements and changes
in the equipment, the illustrations shown may be
di󰀨erent than the actual machine.
FILL IN INFORMATION BELOW
Date of Purchase ______________________________
Model # _____________________________________
Serial # ______________________________________
SKU # ______________________________________
TABLE OF CONTENTS

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 4
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 1: FRAME & CONSOLE GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 5
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 1: FRAME & CONSOLE GROUPING
ITEM # PART # DESCRIPTION QTY.
1 61213 MAIN FRAME, CPU-12 1
2 61209 COVER, DRUM (HOOD), CPU-12 1
3 61210 ROD, ALLTHREAD 1/2-13 HOOD LATCH 2
4 61208 TUBE, HOOD LATCH 3/4”OD X 3-3/4”L 2
5 10312 WASHER, FLAT 1/2 SAE ZINC 2
6 40358 NUT, TAIL HANDLE 1/2-13 2
7 10407 NUT, HEX LOCK 1/2-13 ZINC 2
8 61304K CONSOLE, CPU12-35K 1
9 10021 SCREW, CAP 3/8-24 X 1 6
10 10025 WASHER, FLAT 3/8 SAE ZINC 12
11 10811 WASHER, LOCK 3/8 ZINC 6
12 10014 NUT, HEX 3/8-24 ZINC 6
13 61305 PANEL, REAR, CPU12-35K 1
14 10806 SCREW, CAP 5/16-18 X 1 4
15 10801 WASHER, LOCK 5/16 ZINC 4
16 10213 WASHER, FLAT 5/16 SAE ZINC 4
17 61003 DOOR, CONSOLE SIDE ACCESS, CPU-12 1
18 10018 SCREW, CAP 1/4-20 X 3/4 4
19 10038 WASHER, LOCK 1/4 ZINC 4
20 10602 WASHER, FLAT 1/4 SAE ZINC 4
21 10608 GRIP, HAND 1” MODEL AT 2
22 51024 HANDLE BAR 24”, ZINC PLATED 2
23 51230 KNOB, STAR CLAMPING 3/8-16 X 1”STUD 2
24 10145 PIN, DETENT RING 3/16 X 1-5/16 E.L. 2

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 6
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 2: LIFTING SYSTEM GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 7
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 2: LIFTING SYSTEM GROUPING
ITEM # PART # DESCRIPTION QTY.
1 75004 HANDWHEEL, LARGE W/ 5/8-8 X 16”ROD 1
2 10411 SCREW, SKT. HD. CAP 1/2-13 X 4 ZINC 1
3 50550 SLEEVE, BRASS 1/2” TAPERED 1
4 10104 KNOB, BALL 1-7/8 W/ 1/2-13THD, BLK. 1
5 80009 BEARING, BALL 5/8” 2-HOLE (NO G.F.) 1
6 10412 BOLT, CARRIAGE 1/4-20 X 1 2
7 10602 WASHER, FLAT 1/4 SAE ZINC 2
8 10861 NUT, KEPS LOCK 1/4-20 ZINC 2
9 55010 SPACER, HANDWHEEL 5/8”ID X 3/4”L 1
10 10096 COLLAR, LOCKING 5/8”ID 1
11 61214 LINKAGE, LOWER CONTROL 25”L, CPU-12 1
12 10808 FITTING, GREASE 1/4-28 STRAIGHT 7
13 10322 SCREW, CAP 1/2-20 X 2 1
14 10205 NUT, HEX LOCK 1/2-20 ZINC 1
15 61218 ARM, CYLINDER CONTROL, CPU-12 1
16 61219 SUPPORT, PIVOT, CPU-12 2
17 10021 SCREW, CAP 3/8-24 X 1 4
18 10025 WASHER, FLAT 3/8 SAE ZINC 8
19 10811 WASHER, LOCK 3/8 ZINC 4
20 10014 NUT, HEX 3/8-24 ZINC 4
21 61020 CYLINDER, HYDRAULIC 1
22 10324 SCREW, CAP 1/2-13 X 3-1/2 1
23 10009 WASHER, FLAT 3/4 SAE ZINC 3
24 61217 TUBE, CYL. 3/4”OD X 2-5/16, CPU-12 1
25 10407 NUT, HEX LOCK 1/2-13 ZINC 1
26 10326 SCREW, CAP 5/8-11 X 3 1
27 10809 NUT, HEX LOCK 5/8-11 ZINC 1
28 61216 FORK, OUTRIGGER, CPU-12 1
29 50030 WHEEL 6 X 2 X 3/4”BRG.,ALUM./RUBBER 2
30 61048 AXLE TUBE 3/4ODX1/2IDX3-1/16, CPU12 2
31 61047 SPACER, WHEEL 3/4”ID X 13/32, CPU12 4
32 81001 SCREW, CAP 1/2-13 X 4 2
33 10407 NUT, HEX LOCK 1/2-13 ZINC 2

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 8
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 3: HYDRAULIC PUMP GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 9
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 3:
HYDRAULIC PUMP GROUPING
ITEM # PART # DESCRIPTION QTY.
1 50227 PUMP, HYDRAULIC ELEC., 12VDC M-301 1
2 10710 FITTING, SWIVEL 45, 1/4NPT HYD. 1
3 57078 HOSE, HYDRAULIC 1/4NPT X 6-1/2”LOA 1
461116 VALVE, FLOW CONTROL 2
5 10717 NIPPLE, HEX 1/4 NPT (BRASS) 1
6 61215 HOSE, HYDRAULIC 1/4NPT X 27-1/2”LOA 1
7 10709 FITTING, SWIVEL 90, 1/4NPT HYD. 1
8 10055 SCREW, CAP 3/8-16 X 1 2
9 10811 WASHER, LOCK 3/8 ZINC 2
10 10025 WASHER, FLAT 3/8 SAE ZINC 2
11 61064 CABLE, EYE-EYE 4GA. X 40” (RED) 1
12 10342 SCREW, CAP 5/16-18 X 1-1/2 1

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 10
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 4: REAR AXLE & JACKSHAFT GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 11
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 4: REAR AXLE & JACKSHAFT GROUPING
ITEM # PART # DESCRIPTION QTY.
1 61228 AXLE SHAFT 1”DIA. X 30”L, CPU-12 1
2 10115 KEY 1/4SQ X 2 1
3 61126 SPROCKET #40B34 X 1”BORE 1
4 61052R BEARING, BALL 1” MODIFIED 3-HOLE RIGHT SIDE 1
5 61052L BEARING, BALL 1” MODIFIED 3-HOLE LEFT SIDE 1
6 10132 KEY 1/4SQ X 3 2
7 61231 SPACER, WHEEL 1”ID X 2-3/4”L 1
8 10008 WASHER, FLAT 1” SAE ZINC 1
9 61065 WHEEL 8 X 3 X 1”BORE 2
10 10312 WASHER, FLAT 1/2 SAE ZINC 2
11 10045 WASHER, LOCK 1/2 ZINC 2
12 10914 SCREW, CAP 1/2-13 X 1 2
13 10309 SCREW, CAP 3/8-24 X 1-1/4 ZINC 6
14 10025 WASHER, FLAT 3/8 SAE ZINC 12
15 10811 WASHER, LOCK 3/8 ZINC 6
16 10014 NUT, HEX 3/8-24 ZINC 6
17 61053 JACKSHAFT 3/4”DIA. X 5”L, CPU-12 1
18 10016 KEY 3/16SQ X 1-1/2 1
19 61124 SPROCKET, DUAL #3560-4010, CPU-12 1
20 50045 BEARING, BALL 3/4” PILLOW BLOCK 2
21 10804 BOLT, CARRIAGE 3/8-16 X 1-1/2 F.T. 4
22 10025 WASHER, FLAT 3/8 SAE ZINC 4
23 10811 WASHER, LOCK 3/8 ZINC 4
24 10404 NUT, HEX 3/8-16 ZINC 4
25 50048 SPROCKET #3511 X .67”BORE 1
26 50071 KEY, WOODRUFF 1/8 X 1/2 (SAE #3) 1
27 61229 CHAIN #35 X 26-1/8” + CL, CPU-12 1
28 61230 CHAIN #40 X 24-13/16” + CL, CPU-12 1

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 12
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 5: TRANSMISSION, DRIVE LEVER & LINKAGE GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 13
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ITEM # PART # DESCRIPTION QTY.
1 10920 KNOB, BALL 1-3/8 W/
5/16-24THD, BLK
1
2 61221 LEVER, DRIVE, CPU-12 1
3 10312 WASHER, FLAT 1/2 SAE ZINC 3
4 10340 BOLT, TAP 1/2-13 X 3
(FULL THREAD)
1
5 10417 NUT, HEX 1/2-13 ZINC 2
6 10013 NUT, HEX 1/4-20 ZINC 2
7 50074 SPRING, EXT. 1”OD X 3-15/16 1
8 10602 WASHER, FLAT 1/4 SAE ZINC 1
9 10905 SCREW, CAP 1/4-20 X 1-1/4 1
10 61223 LINKAGE, ROD 3/8 X 19-1/4”L 1
11 10014 NUT, HEX 3/8-24 ZINC 3
12 10919 ROD END, FEMALE
3/8-24 R.H. THREAD
3
13 10919L ROD END, FEMALE
3/8-24 L.H. THREAD
1
14 10816 SCREW, CAP 3/8-24 X 1-1/2 3
15 10011 SPACER, STEEL
9/16OD X 3/8ID X 3/8
4
16 10004 NUT, HEX LOCK 3/8-24 ZINC 4
17 61038 PIVOT LINKAGE CONNECTOR,
TRANS.
1
18 10205 NUT, HEX LOCK 1/2-20 ZINC 1
19 10422 NUT, ACORN 1/2-20 1
20 61224 LINKAGE, ROD 3/8 X 6-1/2”L 1
ITEM # PART # DESCRIPTION QTY.
21 10816 SCREW, CAP 3/8-24 X 1-1/2 1
22 61225 TRANS., CONTROL ARM, CPU12 1
23 10811 WASHER, LOCK 3/8 ZINC 1
24 10404 NUT, HEX 3/8-16 ZINC 1
25 61226 MOUNT, TRANSMISSION CPU12 1
26 10819 BOLT, CARRIAGE 5/16-18 X 1
FULL THD
4
27 10213 WASHER, FLAT 5/16 SAE ZINC 4
28 10801 WASHER, LOCK 5/16 ZINC 4
29 10054 NUT, HEX 5/16-18 ZINC 4
30 50061 TRANSMISSION, HYDROSTATIC 1
31 50071 KEY, WOODRUFF
1/8 X 1/2 (SAE #3)
3
32 50048 SPROCKET #3511 X .67”BORE 1
33 10909
10910
BOLT, CARRIAGE 3/8-16 X 3
BOLT, CARRIAGE 3/8-16 x 4”F.T.
3
1
34 10040 WASHER, GARRET
17/32 X 1 X .054
4
35 10811 WASHER, LOCK 3/8 ZINC 4
36 10404 NUT, HEX 3/8-16 ZINC 4
37 50062 SHEAVE, TRANS.
4”OD X 1GR. X .671”B
1
38 50266 FAN BLADE W/ PLATE 7”,
TRANSMISSION
1
39 10038 WASHER, LOCK 1/4 ZINC 1
40 10834 SCREW, CAP 1/4-20 X 1/2 ZINC 1
PARTS LISTING - ILLUSTRATION 5:
TRANSMISSION, DRIVE LEVER & LINKAGE GROUPING

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 14
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 6: 5th WHEEL GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 15
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 6: 5th WHEEL GROUPING
ITEM # PART # DESCRIPTION QTY.
1 61202 LATCH, REAR CASTER LEVER, CPU-12 1
2 10018 SCREW, CAP 1/4-20 X 3/4 1
3 10602 WASHER, FLAT 1/4 SAE ZINC 2
4 10861 NUT, KEPS LOCK 1/4-20 ZINC 1
5 10608 GRIP, HAND 1” MODEL AT 1
661110 LEVER, REAR CASTER, CPU-12 1
7 50072 PIN, ROLL 1/4 X 2 1
8 10304 SCREW, CAP 1/2-20 X 1 2
9 10045 WASHER, LOCK 1/2 ZINC 2
10 61205 SHAFT 1”RD X 20-3/8”L, CPU-12 1
11 10427 COLLAR, LOCKING 1”ID 2
12 10030 SCREW, CAP 3/8-24 X 2 1
13 10004 NUT, HEX LOCK 3/8-24 ZINC 1
14 61206 LINKAGE, REAR CASTER, CPU-12 1
15 4805 ROD END, MALE 1/2-20 1
16 10312 WASHER, FLAT 1/2 SAE ZINC 2
17 10407 NUT, HEX LOCK 1/2-13 ZINC 1
18 50074 SPRING, EXT. 1”OD X 3-15/16 1
19 61120 CARRIAGE, CASTER BASE, CPU-12 1
20 10309 SCREW, CAP 3/8-24 X 1-1/4 ZINC 4
21 10113 SPACER, STEEL 9/16OD X 3/8ID X 7/32 4
22 10025 WASHER, FLAT 3/8 SAE ZINC 4
23 10004 NUT, HEX LOCK 3/8-24 ZINC 4
24 61121 CASTER, SWIVEL W/ 5” C.I. WHEEL 1
25 10321 SCREW, CAP 1/2-20 X 1-1/4 2
26 10312 WASHER, FLAT 1/2 SAE ZINC 4
27 10205 NUT, HEX LOCK 1/2-20 ZINC 2

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 16
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ITEM # PART # DESCRIPTION QTY.
1 10711A VALVE & HOSE CONNECTOR ASSY. 1
2 80021 CONN., SWIVEL FEM. 3/4HOSE X 1/2MPT 1
3 10711 VALVE, BALL 1/2 FPT 1
4 50077 BARB, 3/8HOSE X 1/2MPT 1
5 50069 CLAMP, HOSE, SAE #6, ADJ. TO 13/16 2
6 61220 HOSE 3/8”ID X 40-1/2”L, CPU-12 1
7 50075 BARB, 3/8 HOSE X 1/4MPT (BRASS) 1
8 80029 NOZZLE, SPRAY 1/4NPT (BRASS) 1
ILLUSTRATION 7: WATER VALVE & HOSE GROUPING

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 17
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 8: LIFTING BAIL GROUPING
ITEM # PART # DESCRIPTION QTY.
1 61302K BAIL, LIFTING, CPU12-35K 1
2 10321 SCREW, CAP 1/2-20 X 1-1/4 4
3 10312 WASHER, FLAT 1/2 SAE ZINC 4
4 10045 WASHER, LOCK 1/2 ZINC 4
5 10072 NUT, HEX 1/2-20 ZINC 4
6 61303K SUPPORT, LIFTING BAIL, CPU12-35K 1
7 10309 SCREW, CAP 3/8-24 X 1-1/4 ZINC 2
8 10021 SCREW, CAP 3/8-24 X 1 2
9 10025 WASHER, FLAT 3/8 SAE ZINC 6
10 10811 WASHER, LOCK 3/8 ZINC 4
11 10014 NUT, HEX 3/8-24 ZINC 4

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 18
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 9:
BEARING GROUPING FOR CUTTER DRUM
ITEM # PART # DESCRIPTION QTY.
1 61235 BEARING, ROLLER 1-1/2” 3-HOLE CPU12 FB22424EHC
(INCLUDES ITEM 2 - STEEL CAP)
1
2 61237 BEARING STEEL CAP, CPU-12 1
3 61236 BEARING, ROLLER 1-1/2” 3-HOLE CPU12 FB22424EH 1
4 61247 BEARING STEEL FLINGER, CPU-12 1
5 61238 BEARING DUST SHIELD W/SEAL, CPU-12 2
6 10308 SCREW, CAP 1/2-20 X 1-1/2 6
7 10312 WASHER, FLAT 1/2 SAE ZINC 12
8 10205 NUT, HEX LOCK 1/2-20 ZINC 6
9 61239 RUBBER SEAL 1-3/4”SQ, CPU-12 2

E-CPU12-PL-0417
Printed in USA
JWA ©2017
Page 19
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ITEM # PART # DESCRIPTION QTY.
1 61320 DRUM ASSY. COMP. CPU-12 (INCLUDES ITEMS 2 THRU 8) 1
2 61321 DRUM ONLY, CPU-12 1
3 84063 BUSHING, DRUM, HARDENED STL 3/4”ID 18
4 61234 RETAINING PLATE, CUTTER SHAFT (2 SLOT) 3
5 61249 RETAINING PLATE, CUTTER SHAFT (4 HOLE) 3
6 10025 WASHER, FLAT 3/8 SAE ZINC 12
7 10811 WASHER, LOCK 3/8 ZINC 12
8 10912 SCREW, CAP 3/8-16 X 7/8 (GRADE 8) 12
9 20010 CP412 SHAFT 3/4 X 13-5/8, CPU-12 6*
10 20060 CP403 SPACER, HARDENED STEEL 1-1/2OD X 3/4ID *SEE
NOTE
11
20136
20056
20086
CUTTER WHEELS:
CP408TV CARBIDE 3-1/8”OD X 1-3/16”ID X 5/16”THK 8-POINTS
CP405P POINTED STEEL 3”OD X 1”ID X 3/16”THK 18-TEETH
CP405 FLAT TIP STEEL 3”OD X 1”ID X 3/16”THK 15-TEETH
*SEE
NOTE
*NOTE:
CUTTER WHEELS, SPACERS AND SHAFTS ARE NOT INCLUDED WITH THE DRUM ASSEMLY.
THE NUMBER OF CUTTER WHEELS AND SPACERS VARY WITH THE TYPE OF SET-UP USED.
REFER TO ASSEMBLY INSTRUCTIONS FOR SUGGESTED SET-UPS AND QUANTITIES.
ILLUSTRATION 10:
CUTTER DRUM ASSEMBLY

E-CPU12-PL-0417
Printed in USA
©2017 JWA
Page 20
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 11: ENGINE & MOUNT GROUPING