Eddylight LED GOBO User manual

LED GOBO Light
30-watt LED (white)
USER MANUAL

PACKAGE CONTENTS
1 X LED GOBO Light 30-watt LED
1 X AC power cable
1 X User’s manual
1 X IR controller
1 X gobo ring
1 x gobo clip
SAFETY INSTRUCTIONS
FEATURES
DIMENSIONS
DMX TERMINATION
CONTROL PANEL
TABLE OF CONTENTS
PACKAGE CONTENTS 2
3
4
MENU SYSTEM
DMX CONTROL
TROUBLESHOOTING
SPECIFICATIONS
4
4
5
6
7
9
10
IR REMOTE 8

Caution! There are no user serviceable parts inside the unit. Do
not open the housing or attempt any repairs yourself.
Please read these instructions carefully.They include
important information about the installation,usage and
maintenance of this product.
Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also
receive this User Guide.
ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the ficture.
To prevent risk of fire or shock, do not expose fixture to rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace
with same fuse size and type.
ALWAYS secure fixture using a safety chain. NEVER carry the fixture by its cord. Use its carrying
handles.
DO NOT operate at ambient temperatures higher than 104°F (40°C).
In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
NEVER connect the device to a dimmer pack
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.
SAFETY INSTRUCTIONS

30-watt white LED.
2,3,4 -channel DMX modes.
USB for wireless receiver/transmitter.
32-bit smooth dimming technology, flicker free for TV and camera shooting.
IR control:Infrared remote control up to 45 ft./ 15M .
Variable electronic strobe, dimming and color changing effect.
Stand-alone, Master/Slave and DMX modes.
DIMENSIONS
DMX TERMINATION
FEATURES
As with all DMX devices, the last unit in any chain must have a DMX terminator
connected to the DMX output. If using just a single light,connect a DMX terminator
to the DMX output.
A DMX terminator is a DMX plug with a 120-ohm, 1/4-watt resistorsoldered
between pins 2 and 3.
1
3
2

CONTROL PANEL
UP DOWN
MENU
POWER IN USB for
wireless DMX
DMX OUTDMX IN
ENTER

MENU SYSTEM
Use the four buttons (MENU, UP, DOWN, ENTER) to set the mode in which the
light will operate. The buttons perform the following functions:
MENU: Accesses the menu system or backs out of editing an entry.
UP: Selects the previous mode or increases the value of the selected mode.
DOWN: Selects the next mode or decreases the value of the selected mode.
ENTER: Selects the currently displayed mode for editing or accepts the edited value.
The following table shows the menu options, their possible values, and what they mean.
The “nodE” function serves as a speed limiter for manual dims and fades. When set to “nod0”, any
manual dims or fades will be in real time, meaning that light will dim or fade as fast as you move the
slider on the controller. The other “nodE” values (1-4) are progressively slower than real time.
“nodE”
ENTRY
Addr d001-d512 DMX address
DMX channel selection
Strobe mode (fast-slow)
White dimming
Gobo Rotation(slow-fast)
Speed limiter (see “nodE” section for details)
2,3,4CH
FL00-FL99
U000-U255
000-255
10S/30S/60S/90S
OFF nod1-nod4
CHnd
FLAS *
RL- - *
gobo *
LEd
nodE
VALUES REMARKS
yes/no
rest
Displays the software version numberUE2.0
UErn

DMX CONTROL
When the light is set to a DMX address it will respond to signals from a DMX controller. The number
and complexity of the signals it can respond to correspond directly to the number of channels
selected. The following tables show the functions and values for each channel in the three different
channel modes (2,3,4).
2CH Mode
3CH Mode
4CH Mode
1
1
1
2
3
4
2
3
Dimmer
Dimmer
Dimmer
Strobe
Strobe
Macro
Dimmer Off to Full
Dimmer Off to Full
No Function
Strobe (Slow to fast)
Random Strobe (Slow to fast)
Dimmer Off to Full
No Function
No Function
Strobe (Slow to fast)
Random Strobe (Slow to fast)
Macro Effect 1 (Slow to fast)
Macro Effect 2 (Slow to fast)
Macro Effect 3 (Slow to fast)
Macro Effect 4 (Slow to fast)
Macro Effect 5 (Slow to fast)
Gobo Index
0-255
0-255
0-1
2-196
197-255
0-255 255
0
0
0
0-1
2-196
197-255
0-1
2-50
51-100
101-150
151-200
201-255
0-150
151-200
201-205
206-255
0-150
151-200
201-205
206-255
255
255
0-150
151-200
201-205
206-255
Gobo Index
Clock Wise Rotation (Slow to Fast)
Counter Clock Wise Rotation (Slow to Fast)
Stop
Clock Wise Rotation (Slow to Fast)
Counter Clock Wise Rotation (Slow to Fast)
Stop
Gobo Index
Clock Wise Rotation (Slow to Fast)
Counter Clock Wise Rotation (Slow to Fast)
Stop
Gobo
Rotation
Gobo
Rotation
Gobo
Rotation
20
0
0
DMX Chanel Function Description Value Init
DMX Chanel Function Description Value Init
DMX Chanel Function Description Value Init

IRC REMOTE
When using IR remote controller, please turn off wireless DMX and cut off DMX connections.
dimmer: Press “white” use the up/down keys to select desired fade speed
strobe: Press “strobe” use the up/down keys to select desired strobe speed settings.
gobo rotation: Press “smooth” use the up/down keys to select desired gobo rotation speed
The function of each button on the remote controller is shown in below chart.
up down OFF ON
white
strobe
gobo rotation

TROUBLESHOOTING
Following are some sample problems and potential solutions to those problems.
Q1: The light does not turn on and the menu will not display.
A1: Check the power cable to ensure it is properly plugged in. Check the source power
outlet by plugging in a different device.
Q3: The light does not respond to DMX commands.
A2: Using the menu, ensure that the color dimmers are not all set to 000.
Q2: The light will not turn on, but the menu does display.
A3: Ensure that the light is set to DMX mode with a valid DMX address. Check for
address conflicts with other devices. Check the cabling to ensure that there is
continuity between the light and the DMX controller. Verify that there is a terminator
at the end of the chain. Verify that the DMX controller is operating properly with
another DMX device.

SPECIFICATIONS
Input Voltage
Power Consumption
LEDs
LED Life Span
DMX Channels
Control Protocol
Control Mode
Signal Input&Output
Function Effect
Refresh Rate
Beam Angle
Cooling Mode
Protection Grade
Anti-electricity Intension
Insulation Resistance
Dimensions
Weight
AC 100V - 260V,50-60Hz
35W
30- watt white LED
50000 ~100000 hours
2,3,4 CH
USITT DMX512
Standalone, Auto
3 - pin XLR Male, 3 - pin XLR Female
Dimmer, Strobe, Eotic, Gradual Change
1.5KHz
15° - 25°
Natural convection(no fan, no noise)
IP20
>1.5KV
256 X 193 X 248 mm
3.2kg
IR Control Infrared remote control up to 15 ft./ 45M .
>2Ω

LED GOBO Light
30-watt LED (white)
USER MANUAL