Eddylight 4 in 1 RGBW SlimPar LED Q18 User manual

4 in 1 RGBW SlimPar LED Q18
USER MANUAL

Thank you for purchasing our 4 in 1 RGBW SlimPar LED Q18. Please read these instructions carefully before
operating to avoid any possible damage and accidents caused by misuse.
The Small Cube light has a hydrodynamic aluminum shell. Four integrated, high-brightness LED lights (containing
red, green, blue, white) are used to create a wide spectrum of colors. Each red, green, blue and white color can be
independently mixed, dimmed, faded and so on. It draws low power and is low weight, and is remote controllable. The
DMX controls include dimming, fade, strobe, gradual change and more. The unit is compatible with the standard DMX
512 signal for external DMX control. Practical uses of the product include dance halls, stage backgrounds, hotels and
drapery uplighting.
• Please consult skilled service technicians for any repairs required
• Always disconnect from the power source before setting up, moving and servicing
• Avoid direct eye contact to the light when in operation
• Make sure the power supply voltage is compatible with this light
•Before installation, please check the light’s fasteners and mechanical structure is in good condition and not
damaged
• The light is designed for indoor use, below 40 degrees celsius
•

• Please ensure the ground is always connected
•
• Low-voltage power converter/cable
• Remote control
• User manual
INTRODUCTION
SAFETY INFORMATION
Packing List

Voltage: 
Power: 180W
Lamp Type: 
DMX Channel: 4/8A/8B
Rated: IP20
Size: 140mm deep x 190mm wide x 240mm high
Lamp Angle: 25-45 degrees (produces a 5’ dia. spot of light from a 10’
distance, with a 2’ concentrated center of light)
Net Weight: 2.5Kg
PHOTOS AND SPECIFICATIONS
3.14"
8.2"
11.8"
10.2"
8.2"

MAIN FUNCTION
4 Channel Mode:
Channel DMX Value Function Notes
1
2
3
4
0 - 255
0 - 255
0 - 32
0 - 255
Red dimming 0—100%
Green dimming 0—100%
Blue dimming 0—100%
White dimming 0—100%
8 Channel Mode:
Channel DMX Value Function Notes
1
2
3
4
0 - 255
0 - 255
0 - 255
0 - 255
0—100%
Green dimming 0—100%
Blue dimming 0—100%
White dimming 0—100%
5
6
7
8
0 - 255
0 - 255
0 - 255
0 - 255
Red dimming 0—100%
Strobe
Sound Activated
Sound Activated Slow to FastSpeed Slow to Fast
8B Channel Mode:
Channel DMX Value Function Notes
1
2
3
4
0 - 255
0 - 255
0 - 255
0 - 255
General dimming 0—100%
Strobe
Speed Slow to Fast
5
6
7
8
0 - 255
0 - 255
0 - 255
0 - 255
Red dimming 0—100%
Green dimming 0—100%
Blue dimming 0—100%
White dimming 0—100%

MENU items:
• “Addr”: DMX mode (001-512)
• “Slav”: Slave mode
•
• “SouA”: Sound activated mode
• “SP”: Built-in program speed change mode (speed = 0-15)
• “Pr”: Built-in preset programs (0-11)
• “Colo”: Preset colors (0-30)
• “Strb”: Strobe mode (speed = 0-15)
• “r”: Solid color mode, red setting (0-255)
• “g”: Solid color mode, green setting (0-255)
• “b”: Solid color mode, blue setting (0-255)
• “w”: Solid color mode, white setting (0-255)
Press ENTER to save your selection, which means you will enter the menu mode saved previously when you
activate the light next time. For example, if you want to choose DMX mode d017, operate as follows:
MENU: Access the menu or return to a previous menu option
UP: Menu selection or parameter increments
DOWN: Menu selection or parameter increments
ENTER: Select the current menu option
REAR PANEL DISPLAY AND OPERATION
INSTRUCTIONS FOR MANUAL PROGRAMMING

Creating Solid Colors: (r, g, b)
Sample Colors
• Press MENU repeatedly until “Addr”
• Press UP / DOWN to select your desired address (ie. “d017”)
• Press ENTER to choose.
• Press MENU until “r”, “g” or “b” is selected.
• Press UP / DOWN until to change the number (brightness of that color)
• Press ENTER to choose
• Repeat the process for each color, including white
WhiteBlueGreenRedNameColor
Red
Green
Blue
White
Yellow
Magenta
Cyan
Warm White
255
0
0
0
255
255
0
255
0
255
0
0
255
0
255
255
0
0
255
0
0
255
255
255
0
0
0
255
0
0
0
255

MASTER/SLAVE CONTROL
The MASTER functions as a master as long as it’s not in DMX mode (and ideally no cable plugged into the DMX

more than 20 lamps or 60m of DMX cable.

Only one light can be set as a master, but multiple lights can be set as slaves.
CABLE CONNECTION
A standard XLR connection is used for the DMX 512 protocol:
DMX512 does not include automatic error checking and correction, and so is not an appropriate control for

electromagnetic interference, static electricity discharges, improper cable termination, excessively long cables, or
poor quality cables.

NOTE
In order to avoid failures and signal interference, it is
recommended to connect a 120Ω resistor (1/4W) at
the end of the DMX connection as shown on right. If
using 5-pin DMX, please use a
5-pin to 3-pin cable adapter. Details on
configuration below:
Termination reduces signal errors and avoids
signal transmission problems and interference. It
is always advisable to connect a DMX terminal,
(Resistance 120 Ohm 1/4 W) between PIN 2

1
2
3
3-PIN XLR to 5-PIN XLR Conversion
Conductor
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
PIN 1
PIN 2
PIN 3
Not Used
Not Used
PIN 1
PIN 2
PIN 3
Do Not Use
Do Not Use
3-PIN XLR Female (Out) 5-PIN XLR Male (In)

DOWNLOAD
INSTRUCTIONS
7k 5 in 1