Edge-Core AS5610-52X User manual

– 1 –
Quick Start Guide
1. Unpack the Switch and Check Contents
AS5610-52X 10G Top-
of-Rack Switch
Rack Mounting Kit—Contains two brackets and eight
screws for attaching the brackets to the switch.
Grounding Wire
Power Cord—either Japan, US, Continental Europe
or UK
Console Cable—RJ-45 to DB-9
Documentation—Quick Start Guide (this document)
and Safety and Regulatory Information
Note: For information on switch software, refer to
www.edge-core.com.
Switches with part numbers 5610-52X-D*-******** have
switch software pre-loaded on the switch. Software user
documentation can be found at www.edge-core.com.
Switches with part numbers 5610-52X-O-******** have the
Open Network Installer Environment software installer pre-
loaded on the switch, but no switch software image.
Information about compatible switch software can be
found at www.edge-core.com.
Caution: The switch includes plug-in power supply and
fan tray modules that are installed into its chassis. All
installed modules must have a matching airflow direction.
That is, all modules must have a front-to-back (F2B) airflow
direction, or all modules must have a back-to-front (B2F)
airflow direction. The airflow direction of PSU and fan tray
modules is indicated by labels on the modules.
2. Mount the Switch
Attach the brackets to the switch.
Use the screws supplied with the rack to secure the switch in
the rack.
Caution: Installing the switch in a rack requires two
people. One person should position the switch in the rack,
while the other secures it using the rack screws.
2
1
1
2
3. Ground the Switch
Ensure the rack on which the switch is to be mounted is
properly grounded and in compliance with ETSI ETS 300 253.
Verify that there is a good electrical connection to the
grounding point on the rack (no paint or isolating surface
treatment).
Attach a grounding wire to the grounding point on the
switch rear panel, then to rack ground.
Caution: The earth connection must not be removed
unless all supply connections have been disconnected.
4. Connect Power
Install one or two universal AC power modules in the switch.
The switch supports up to two PSUs that must have the
same matching airflow direction as the installed fan tray.
Connect an external AC power source to the modules.
5. Verify Switch Operation
Verify basic switch operation by checking the system LEDs.
When operating normally, the PSU1/PSU2, Diag, and Fan
LEDs should all be on green.
1
2
1
2
1
2
1
2
1
1
E102013-CS-R01
150200000722A www.edge-core.com
48-Port 10G Top-of-Rack Switch
AS5610-52X

Quick Start Guide
– 2 –
6. Perform Initial Configuration
At this point you may need to make a few basic switch
configuration changes before connecting to the network.
Connect a PC to the switch console port using the included
console cable.
Configure the PC’s serial port: 115200 bps, 8 characters, no
parity, one stop bit, 8 data bits, and no flow control.
Log in to the command-line interface (CLI) using default
settings: User “admin” with no password.
Note: For information on initial switch configuration, refer
to the Administrator’s Guide.
7. Connect Network Cables
For the RJ-45 Management port, connect 100-ohm Category
5, 5e or better twisted-pair cable.
Connect DAC cables to the SFP+/QSFP+ slots. Or first install
SFP+/QSFP+ transceivers and then connect fiber optic
cabling to the transceiver ports.
The following transceivers are supported:
◆40GBASE-CR4
◆40GBASE-SR4
◆10GBASE-CR
◆10GBASE-SR (ET5402-SR)
◆1000BASE-SX (ET4201-SX)
◆1000BASE-LX (ET4201-LX)
Note: As connections are made, check the port status LEDs
to be sure the links are valid.
3
1
2
1
2
3
2
1
1
2
Hardware Specifications
Chassis Specifications
SIze W x D x H:
438.4 x 473 x 43.4 mm (17.26 x 18.62 x 1.71 inches)
Weight 8.395 kg (18.51 lb), with two installed power supply
modules
Temperature Operating: 0° C to 40° C (32° F to 104° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 5% to 95% (non-condensing)
Power Supply Specifications
AC Input 100-240 VAC, 50-60 Hz, 6-3 A
DC Output 5 VDC @ 3 A
12 VDC @ 33 A
Power Supply 100-240 VAC, 50-60 Hz, auto-sensing; hot
pluggable
400 Watts @ 240V/100V per module
Power
Consumption
165 Watts maximum
Maximum
Current
6 A @ 100 VAC
3 A @ 240 VAC
Size W x D x H:
54.5 x 220 x 40.25 mm (2.15 x 8.66 x 1.58 inches)
Regulatory Compliances
Emissions EN 55022:2010, Class A
EN 61000-3-2:2009, Class A
EN 61000-3-3:2008
FCC Class A
VCCI Class A
CE Mark
Immunity EN 55024:2010
IEC 61000-4-2/3/4/5/6/8/11
Safety UL (CSA 22.2 No 60950-1 & UL60950-1)
CB (IEC/EN60950-1)