EdgeStar CWB2886FD User manual
Wine and Beverage
Refrigerator
CWB2886FD
Owner’s Manual
V2.7-07282021www.edgestar.com
2
Important Safety Information
Electrical Safety
Improper handling can cause serious damage to the EdgeStar refrigerator and / or injury to the user.
This refrigerator is designed for domestic indoor use only. Do not use the unit for industrial or
commercial use. Any other use may invalidate the warranty. Please review the ratings label located
on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be
used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of re, electric
shock, or injury.
• Do not exceed the power outlet ratings.
• It is recommended the refrigerator be connected on its own circuit.
• The unit must be installed in accordance with state and local electrical codes.
• A standard electrical supply (115 V, 60Hz), that is properly grounded in accordance with the National
Electrical Code and local codes and ordinances is required.
• Unplug the unit if it is not going to be used for an extended period of time.
• Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose
socket.
• Be sure the refrigerator is properly grounded.
• Avoid installation in high humidity environments such as bathrooms and non-acclimatized
basements. Excess moisture may create condensation on the door and impact the performance of
the refrigerator.
• Never plug or unplug the unit with wet hands.
• Do not bypass, cut, or remove the grounding plug.
• Do not use extension cords or power strips with this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other appliances.
• Never repair the unit while it is plugged in.
• Immediately unplug the unit if it makes strange sounds, emits smells, or smoke comes out of it, and
contact customer service.
• Do not remove any part of the casing unless instructed to do so by an authorized technician.
• You should never attempt to repair the unit yourself. Contact customer service for service options if
the unit needs service.
DANGER: Flammable Refrigerant Used! When handling, moving, and using the refrigerator,
make sure to avoid either damaging the refrigerant tubing or increasing the risk of a leak.
!
3
Important Safety Information
General Safety
• To prevent injuries, use at least two people to move and install the refrigerator.
• Install the refrigerator in a well-ventilated area where the ambient temperature is above 50° F and
below 90° F.
• The temperature range for this refrigerator is optimized for storage. Perishable food items may
• Do not place hot or warm items into the refrigerator before they cool down to room temperature.
• This unit is designed to be installed indoors, and protected from rain, sleet, snow, and / or moisture.
• This unit is not intended to be used by children.
• Children should be supervised to ensure that they do not play with this product.
• Never allow children to crawl inside the refrigerator. If you are disposing of the unit, remove the
door.
thinner.
appliance.
• Do not place the unit near heat sources such as ovens, grills, or direct sunlight.
• Do not pinch or kink the power supply line between the unit and cabinet.
• Do not leave any cleaning solutions in the unit.
• Do not use solvent-based cleaning agents or abrasive solutions to clean the unit as they may
damage the interior and exterior.
• Do not place any other appliances on top of the unit.
• If your model of refrigerator is equipped with a lock, keep the keys away from children.
• Do not move the unit without emptying the contents and securing the door in a closed position.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory, or mental capabilities unless they are given supervision or instruction by a person
responsible for their safety.
• This appliance is meant for use in the household or similar settings.
• Keep all ventilation openings clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process.
• Do not damage the refrigerant circuit.
• Do not use other appliances inside the refrigerator unless recommended by the manufacturer.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a
similarly
!
DISPOSAL: This appliance may not be treated as regular household waste, it should be
taken to the appropriate waste collection
!
4
Table of Contents
Important Safety Information ..........................................................................................2
First-Time Operating Instructions ...................................................................................5
Introduction.....................................................................................................................5
.......................................................................................................... 6
Installation ......................................................................................................................8
Unpacking the Wine and Beverage Refrigerator..................................................... 8
Types of Installation.................................................................................................8
Clearance Requirements.........................................................................................9
Electrical Requirements .......................................................................................... 10
Recommended Grounding Method ......................................................................... 10
Leveling the Refrigerator......................................................................................... 10
Installing the Door Handles ..................................................................................... 11
Installing the Wine Shelves ..................................................................................... 11
Removing the Wine Shelves ................................................................................... 11
Installing the Beverage Shelves.............................................................................. 12
Removing the Beverage Shelves............................................................................ 12
Operation........................................................................................................................13
Installation Checklist before Operation....................................................................13
Using the Temperature Control Panel ..................................................................... 13
Normal Sounds........................................................................................................14
Temperature Alarm .................................................................................................. 14
Defrosting................................................................................................................ 15
Preparing the Refrigerator for Storage.................................................................... 15
Cleaning and Maintenance.............................................................................................15
Troubleshooting.............................................................................................................. 16
.................................................................................................................18
EdgeStar Limited Warranty ............................................................................................19
5
First-Time Operating Instructions
Before use, make sure all packaging labels and materials are removed from the unit. Be sure to keep
track of all included parts and pieces before discarding the packaging materials. It is advised that you
keep the original box and packaging materials in case you ever need to move or ship the appliance in
the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling components time to
settle from transit. The instruction manual should be read before use.
Introduction
Thank you for purchasing this EdgeStar refrigerator. We hope that this purchase will be the beginning of
a lasting and rewarding relationship between you and EdgeStar. We will provide the customer support
and exemplary products necessary to nurture that relationship.
This manual contains important information regarding the proper installation, use, and maintenance of
your refrigerator. Following this manual will ensure that your product will work at its peak performance
Please save the original product packaging in case you need to safely transport your refrigerator.
For Your Records:
Please write down the model number and serial number below for future reference. Both numbers are
located on the ratings label on the back of your unit and are needed to obtain warranty service. You may
also want to staple your receipt to this manual as it is the proof of your purchase, and is also needed
for service under your warranty.
Model Number: ________________________________
Serial Number: ________________________________
Date of Purchase: ______________________________
• If you received a damaged product, immediately contact the retailer or dealer who sold the product.
• Read and follow this instruction manual carefully to help you install, use, and maintain your
refrigerator.
• Read the troubleshooting section of this manual. It will help you diagnose and solve common issues.
• Visit us on the web at www.edgestar.com to register your product, download product guides, and
access additional troubleshooting resources and up-to-date information.
• For warranty service, customer service representatives are available at service@edgestar.com.
6
Parts Identication
Front View:
Rear View:
Note: Gather the model and serial number from the product label and write them down
before installing the refrigerator.
Condenser Fan
Condensation Tray
Compressor
Power Cord
Product Label
Carbon Filter
Control Panel
Door Handle
Internal Fan
Wood Shelf
Leveling Leg
Glass Shelf
Door Lock
Front Vent
7
Internal Fan:
This is an air-cooled unit equipped with an internal fan that maintains a consistent internal
temperature.
Carbon Filter:
Note:
exposure level to odor. If the unit is placed in a kitchen, regular replacement every three
(3) months is ideal.
8
Installation
The refrigerator should be installed in accordance with local electrical code requirements. The refrigerator
should also be placed in a location that is strong enough to support its total weight, keeping in mind that
it will weigh substantially more when fully loaded than when empty. Before you plug the refrigerator
into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s
oils to settle.
Unpacking the Wine and Beverage Refrigerator
Warning: Use two or more people to move and install the refrigerator. Failure to do so
can result in back or other injury. Carefully remove the packaging materials. Remove any
shipping tape and glue from your refrigerator before use. Do not use sharp instruments,
products can damage the surface of your refrigerator.
!
Warning: Do not remove any safety, warning, or product information labels from your
refrigerator.
!
Warning: DO NOT install the refrigerator behind a closed cabinet door.
This refrigerator has been designed for freestanding or built-in installation. In each case, there must be
adequate ventilation and access for service.
Freestanding Installation:
A freestanding installation will allow you to install the refrigerator in almost any place you desire. You
must follow the stated instructions for electrical requirements and leveling the refrigerator.
Built-in Installation:
A built-in installation will allow you to install the refrigerator under a counter as long as the required
clearance space around the refrigerator is provided. It is necessary to allow adequate ventilation space
around the unit, including at the back of the unit.
The following additional items must be observed:
2. If the electrical outlet for the refrigerator is behind the cabinet, plug in the refrigerator.
3. Push the refrigerator into position.
Types of Installation
!
9
Note:
support the entire weight of a fully loaded unit. It is important for the refrigerator to be level
in order to work properly. If needed, you can adjust the height of the refrigerator by rotating
the feet. See the “Leveling the Refrigerator” section.
Note: A standard electrical supply (115V AC only, 60 Hz), properly grounded in accordance
with National Electrical Code and local codes and ordinances, is required.
Notes:
• Choose a location that has ambient temperatures above 50° F and below 90° F. Operation
• This unit MUST be installed in an area protected from the elements, e.g. wind, rain, water
spray or drips.
• The refrigerator should not be located next to ovens, grills, or other heat sources.
• Do not kink or pinch the power supply cord between the refrigerator and the wall or
cabinet.
Clearance Requirements
When installing the refrigerator under a counter, follow the recommended spacing dimensions shown.
To ensure proper service access and ventilation, allow at least 1-2” of clearance at the back, 1/4” at
the top, and 1/4” at the sides. If the door side is against a wall, allow at least 2 5/16” of clearance. The
installation should allow the unit to be pulled forward for servicing, if necessary.
Wall
2 /16”
Min.
1
/8”
Wall
2
/16
”
Min.
1 - 2”
1/4”
1/4”
15 /4”
1/4”
1 - 2”
Top View: Side View:
10
ELECTRIC SHOCK HAZARD!
• Plug into a grounded 3-prong outlet.
• Never remove the grounding prong from the plug.
• Never use an adapter to bypass the grounding prong.
• DO NOT use an extension cord.
!
Electrical Requirements
Recommended Grounding Method
proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in accordance with the National Electrical
Code and local codes and ordinances is required.
It is recommended that a separate circuit, serving only your refrigerator, be provided. Use receptacles
The fuse (or circuit breaker) size should be 15 Amps.
For your personal safety, this appliance must be grounded. It is equipped with a power supply cord that
has a 3-pronged grounding plug. To minimize possible shock hazard, the cord must be plugged into a
mating 3-pronged wall socket and grounded in accordance with the National Electrical Code and local
codes and ordinances. If a mating wall socket is not available, it is the personal responsibility of the
Leveling the Refrigerator
It is important for the refrigerator to be level in order to work properly. It
can be raised or lowered by rotating the plastic sheaths around each of
level, rotate the feet until the refrigerator becomes level. You may need to
make several adjustments to level it. We recommend using a carpenter’s
level to check the machine.
1. Place a carpenter’s level on top of the product to see if the refrigerator
is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the refrigerator.
Turn the leveling feet to the left to raise that side of the refrigerator.
Note:
adjust the feet to level the refrigerator.
11
Installing the Door Handles
To install the door handles:
1. Open the left door and carefully pull the door gasket around the area where the handle
is to be installed.
2. Carefully remove the two pre-installed decorative plugs from the front of the door.
3. Insert each Phillips head screw through the gasket side of the door until the screw
passes through the door.
4. Align the handle with the screws and tighten using a Phillips head screwdriver until the
5. Carefully press the door gasket into its original position.
6. Repeat steps 1 through 5 for the right door handle.
Note: Some refrigerators do not have decorative plugs installed.
Warning: Do not over-tighten the screws as this may cause damage to the handle or the
stainless steel door.
!
Installing the Wine Shelves
their tracks.
1. Open the left zone door completely.
2. Identify the protective stoppers located on the right and left sides of the back of each wooden
wine shelf.
3. Lift either the left or right side of the shelf creating a 45° angle.
4. Insert the shelf at the desired track level and push back
slowly until it stops in place.
5. Gently set the shelf down in place; it should be level.
Removing the Wine Shelves
1. Open the left zone door completely.
2. Make sure the shelf is pushed back completely (towards
the rear wall).
3. If necessary, make sure you remove all the contents
sitting on the shelf.
4. Identify the protective stoppers located on the right and left sides of the back of each wooden
wine shelf.
5. Lift either the left or right side of the shelf creating a 45° angle from its original position. Make
sure not to lift either side of the shelf too hard as it may come in contact with the inner wall mount.
6. Pull the shelf forward until it is completely removed from the inner compartment. Set aside safely.
12
Removing the Beverage Shelves
Installing the Beverage Shelves
tracks.
1. Open the right zone door completely.
2. Ensure that the metal guide posts are attached to the back of the shelf.
3. While lifting the right side of the shelf up 45°, rest the left metal guide post on the shelf track.
4. Slowly push the shelf back until the right metal guide post reaches the vertical indentation in the
cabinet.
5. Gently set the shelf down on the track.
1. Open the right zone door completely.
2. Remove all of the contents loaded on the shelf, if applicable.
3. Ensure that the shelf is pushed back completely.
4. Carefully lift either the left or right side of the shelf up 45°.
5. Pull the shelf forward until it is completely removed from the inner compartment.
Metal Guide Post
13
Operation
Installation Checklist before Operation
Using the Temperature Control Panel
1. Have all packing materials and tape been removed from the interior and exterior of the refrigerator?
2. Have the installation instructions been followed, including connecting the machine to electricity?
And has proper grounding been installed for the refrigerator?
3. Has the machine been leveled?
4. Is the refrigerator in a site where the ambient temperature is between 50° F and 90° F all year
round?
5. Is there a clearance of at least 1- 2” at the rear, 1/4” at the top, and 1/4” at the sides for proper air
circulation?
This wine and beverage refrigerator has two cooling zones that are controlled independently by two
separate control panels, one for the left side zone and one for the right side zone. The left wine zone
has a temperature range from 40° F to 65° F. The right beverage zone has a temperature range from
38° F to 65° F. The control panel in each zone will display the set temperature inside the cabinet.
Power Button:
Up Button: Press to increase the temperature by 1 degree increments.
Down Button: Press to decrease the tempreature by 1 degree increments.
Light Button:
F
Run Light: When lit, the unit is in cooling mode.
i
Celsius/Fahrenheit Light: The Celcius or Fahrenheit light will be lit depending on which
temperature type is being displayed. To switch between C and F press and hold both the
Up and Down buttons simultaneously for approximately 3 seconds. A beep will occur and
the indicator light will illuminate next to desired temperature setting.
i
14
Note: The refrigerator is equipped with a temperature memory function. If power is
suddenly lost, the previously set temperature will be saved and the Refrigerator will return
to this setting once power is restored. Allow at least 24 hours before storing your items to
allow the setting temperature to be reached.
Caution:
!
Normal Sounds
Your new refrigerator may make noise during normal operation. Most of these sounds are normal.
The following describes several sounds you may hear and what may be making them:
refrigerator can also make noises.
• Water running from the evaporator to the water bin may make a splashing sound.
refrigerator.
• You may hear air being forced over the condenser by the condenser fan.
Warning:
• Do not touch the power plug when your hands are wet.
• Never unplug the unit by pulling on the cord.
!
Temperature Alarm
If the interior temperature is higher than 73°F (23°C), “HI” is shown on the temperature
control panel and the temperature alarm will sound continuously after one hour.
This indicates that the inner temperature is too high. If the inner temperature is lower
than 32°F (0°C), “LO” is shown on the temperature display panel and the temperature
reference the troubleshooting section found in this manual or contact EdgeStar for support.
15
Warning: Never attempt to remove frost with a sharp object!
!
Defrosting
Preparing the Refrigerator for Storage
Note that under most refrigerating settings, the unit will automatically defrost in most ambient conditions.
However, on colder settings, some frost may build up. Additionally, the more humid the ambient
conditions, the more frost may build up. Keep the door closed as much as possible and avoid opening
the door unnecessarily to minimize frost build-up. If frost is preventing the door from closing properly,
If the refrigerator will not be used for a long time, or is to be moved to another place, it will be necessary
to defrost the unit and dry the interior.
1. Disconnect the Refrigerator from the power supply by removing the power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent mold, mildew, and unpleasant smells.
Caution: Store the unit out of reach from children. If you have children, you may want to
take precautions such as removing the door to prevent a child from being trapped inside.
!
Cleaning and Maintenance
The door and cabinet may be cleaned with a mild detergent or hand soap mixed with warm water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe
with a soft clean towel to prevent water spotting. If the door panel is stainless steel, it can discolor
when exposed to chlorine gas and moisture. Clean stainless steel using a cloth dampened with a mild
detergent and warm water solution. Never use an abrasive or caustic cleaning agent.
The refrigerator’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and items.
6. Reconnect power to the unit.
Exterior Cleaning
Interior Cleaning
16
Troubleshooting
the problem persists, check the Troubleshooting Guide below and on the following page. The problem
may be something that can easily be solved or explained.
Before Calling for Help:
Symptoms Possible Causes Solutions
The refrigerator turns on and
The room temperature
is higher than the
recommended ambient
environment.
Run the refrigerator at the appropriate
ambient temperature.
The door is being opened
too often.
Minimize the number of times the door
is opened.
The door is not completely
closed.
Make sure the door is completely
closed.
The door gasket is not
sealing properly.
Make sure the door gasket is sealing
properly.
The refrigerator does
not have the suggested
ventilation.
Read and follow the “Installation
Clearance Requirements” section.
The refrigerator does not
turn on.
There is a power failure. Ensure that the refrigerator is plugged
in and the power outlet has power.
The refrigerator is not
plugged in.
Plug the unit in to a power outlet that
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse
box or reset the breaker.
The refrigerator will
not reach the desired
temperature.
The refrigerator is placed too
close to a heat source.
Keep the refrigerator away from direct
sunlight or other heat sources.
The refrigerator does not
Read and follow the “Installation
Clearance Requirements” section.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open
the door too frequently or for a long
period of time.
The refrigerator is making
strange noises.
Certain sounds are normal. Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the
refrigerator is level, and that it is not
in contact with another appliance or
furniture.
17
Symptoms Possible Causes Solutions
The body of the refrigerator
The unit is not grounded
properly.
Contact your local electrician to test
your electrical grounding system.
Frost is forming in the
refrigerator.
The environment is humid. Manual defrosting is required; unplug
the unit to allow the frost to melt. If
frost builds up frequently, you can
move the unit to a location with a
warmer temperature, minimize the
number of times you open the door, or
check the door gasket for a good seal.
The ambient temperature is
too low.
The door gasket is not
installed properly.
The door is being opened
too frequently.
The door will not shut
properly.
The refrigerator is not level. Make sure the refrigerator is on a level
surface.
The door gasket is dirty. Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is correctly
installed.
The shelves are incorrectly
installed.
Install the shelves correctly.
18
Specications
Note: Technical data and performance information are provided for reference only.
most accurate information.
Product Type Wine and Beverage Refrigerator
Model CWB2886FD
Voltage / Frequency AC 115V~60Hz
Amperage 1.2
Color Black Cabinet; Stainless Steel Door
Refrigerant R600a
Storage Capacity 28 Bottles*
86 Standard 12 oz. Cans
Temperature Range Beverage Zone: 38°F - 65°F
Wine Zone: 40°F - 65°F
Dimensions
(Height x Width x Depth )
” x 29 ¹/”
Note: The refrigerator can store 28 standard 750 ml. wine bottles.
Note: 16”.
19
EdgeStar Limited Warranty
WHAT IS COVERED:
LABOR: For a period of ONE (1) YEAR from the date of original purchase, labor will be performed free of charge at an authorized
EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts, or exchange the defective product
with a new, refurbished, or remanufactured product. If a product is replaced, it will carry the remaining warranty of the original product.
After the one (1) year period, EdgeStar will no longer be responsible for labor charges incurred. All defective products and parts covered
by this warranty will be repaired or replaced on a mail-in basis to an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or refurbished parts free of
charge. EdgeStar may request a defective part be returned in exchange for the replacement part. All replacement parts or products will
be new, remanufactured, or refurbished. All products and parts replaced by EdgeStar under warranty service become the property of
EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during operation of the product
under normal service, maintenance, and usage conditions. This warranty applies to the purchase and use of this product in residential
settings within the contiguous United States of America.
WHAT IS NOT COVERED- The following limitations apply to the coverage of this warranty. This warranty does not
cover:
• Labor charges for installation, setup or training to use the product.
• Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any damaged
caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
• Cosmetic damage such as scratches and dents.
• Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
• Labor, service transportation, and shipping charges incurred 91 days or more after the date of original purchase.
• The use of EdgeStar products in commercial or rental settings.
• Optional accessories, attachments, and appearance items.
• Products lost in shipment, or theft.
• Products sold AS IS or from an unauthorized reseller.
• Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
• Damage to personal property from use of product.
• Replacement of repair of household fuses, circuit breakers, wiring, or plumbing.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for
troubleshooting assistance and warranty service at www.edgestar.com or call 1-866-319-5473. Before contacting Customer Support you
are required to have your model number, serial number, and proof of purchase available upon request. Once an EdgeStar authorized
authorized repair facility. EdgeStar is not responsible for damage resulting from shipper mishandling or improper packaging. Do not return
a defective product to the place of purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS
REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER
NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE
WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. IN NO EVENT AND UNDER NO CIRCUMSTANCE OF ANY TYPE OR
KIND SHALL THE SELLER, MANUFACTURER AND/OR DISTRIBUTOR BE LIABLE FOR ANY REASON, UNDER ANY THEORY, FOR
MORE THAN THE BASIC COST OF THE PRODUCT TO THE PURCHASER OR END USER. SOME STATES DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
One (1) Year Parts & One (1) Year Labor
This product is warranted by EdgeStar and is subject to any conditions set forth as follows:
www.edgestar.com ©2021 EdgeStar
Other manuals for CWB2886FD
1
Table of contents
Other EdgeStar Wine Cooler manuals
EdgeStar
EdgeStar CWR460DZ User manual
EdgeStar
EdgeStar CWR450DZ User manual
EdgeStar
EdgeStar TWR182ESS User manual
EdgeStar
EdgeStar CWF440SZ User manual
EdgeStar
EdgeStar CWR265SZ User manual
EdgeStar
EdgeStar AVALLON User manual
EdgeStar
EdgeStar CWR260DZ User manual
EdgeStar
EdgeStar CWB2150FD User manual
EdgeStar
EdgeStar TWR325ESS User manual
Popular Wine Cooler manuals by other brands
AGA
AGA Wine cellar user manual
Viking
Viking Designer DDWB300 installation instructions
Soleus Air
Soleus Air JC-128 owner's manual
Lamona
Lamona LAM6904 Instructions and installation
Haier
Haier HVDW15ABB - 15 Bottle Display Window Wine... user manual
Fhiaba
Fhiaba GranMaestro Series Installation guide and user's manual
