Edgetech 8011M User manual

EdgeTech
4 Little Brook Road
West Wareham, MA 02576
Tel: [phone]
Fax: [phone]
www.EdgeTech.com
8011M ACOUSTIC DECK UNIT
USER HARDWARE MANUAL
0004811_REV_F 9/7/2021

ii
8011M ACOUSTIC DECK UNIT 0004811_REV_F
The information, figures, and specifications in this manual are proprietary. They are issued in strict
confidence on condition that they not be copied, reprinted, or disclosed to a third party, either wholly or
in part, without the prior, written consent of EdgeTech. Any reproduction of EdgeTech supplied software
or file sharing is strictly prohibited.
Copyright © 2011 – 2021 EdgeTech. All rights reserved.
Storm Case™ is a trademark of Pelican.
Benthos©is a registered trademark of Teledyne Marine

iii
ATTENTION – READ THIS FIRST!
All personnel involved with the installation, operation, or maintenance of the equipment described in this
manual should read and understand the warnings and cautions provided below.
CAUTION!
This equipment contains devices that are extremely sensitive to static
electricity. Therefore, extreme care should be taken when handling them.
Normal handling precautions involve the use of anti-static protection
materials and grounding straps for personnel.
WARNING!
High Voltage may be present in all parts of the system. Therefore, use
caution when the electronics are removed from their containers for
servicing.
CAUTION!
Operation with improper line voltage may cause serious damage to the
equipment. Always ensure that the proper line voltage is used.
Warnings, Cautions, and Notes
Where applicable, warnings, cautions, and notes are provided in this manual as follows:
WARNING!
Identifies a potential hazard that could cause injury or death.
CAUTION!
Identifies a potential hazard that could damage equipment or data.
NOTE: Recommendations or general information that is particular to the
material being presented.

iv
8011M ACOUSTIC DECK UNIT 0004811_REV_F
HARDWARE VARIATIONS AND COMPATIBILITY
The 8011M Acoustic Deck Unit contains both standard and proprietary hardware. At times, EdgeTech may
change the standard components due to their availability or performance improvements. Although the
component manufacturers and their models and styles may change from unit to unit, replacement parts
will generally be interchangeable.
EdgeTech will make every effort to see that replacement components are interchangeable and use the
same software drivers (if applicable). At times, however, direct replacements may not exist. When this
happens, EdgeTech will provide the necessary drivers with the replacement part, if applicable.
EdgeTech may also change certain hardware per customer requirements. Therefore, portions of this
manual, such as parts lists and test features, are subject to change. These sections should be used for
reference only. When changes are made that affect system operation, they will be explicitly noted. Some
options and features may not be active in the customer’s unit at the time of delivery. Upgrades will be
made available when these features are implemented.
Contact EDGETECH CUSTOMER SERVICE with any questions relating to compatibility.

v
ABOUT THIS DOCUMENT
We, the employees at EdgeTech, would like to thank you for purchasing 8011M. At EdgeTech, our policy
is to provide high-quality, cost-effective products and support services that meet or exceed your
requirements. We also strive to deliver them on time and to look for ways to improve them continuously.
We take pride in the products we manufacture and want you to be entirely satisfied with your equipment.
Purpose of this Manual
The purpose of this manual is to provide the user with information on the setup and use of EdgeTech’s
8011M. Although this manual encompasses the latest operational features of the unit, some features may
be periodically upgraded. Therefore, the information in this manual is subject to change and should be
used for reference only.
Liability
EdgeTech has made every effort to document the 8011M in this manual accurately and completely.
However, EdgeTech assumes no liability for errors or any damages resulting from the use of this manual
or the equipment it documents. EdgeTech reserves the right to upgrade this equipment's features and
make changes to this manual without notice at any time.
Revision History
REVISION
DESCRIPTION
DATE
APPROVAL
A
Transfer to Epicor
01/02/2011
GE
B
Changed Transducer Connection
02/17/2011
GE
C
Updated Format
09/03/2015
RM
D
Include URI Inverted Echo
02/25/2016
RM
E
Updates to content, images, and light indication
3/6/2019
RM
F
Added Benthos Instructions
9/7/2021
GM

vi
8011M ACOUSTIC DECK UNIT 0004811_REV_F
WARRANTY STATEMENT
All equipment manufactured by EdgeTech is warranted against defective components and workmanship
for a period of one year after shipment. Warranty repair will be done by EdgeTech free of charge.
Shipping costs are to be borne by the customer. Malfunction due to improper use is not covered in the
warranty, and EdgeTech disclaims any liability for consequential damage resulting from defects in the
equipment's performance. No product is warranted as fit for a particular purpose, and there is no
merchantability warranty. This warranty applies only if:
i. The items are used solely under the operating conditions and in the manner recommended in the
Seller's instruction manual, specifications, or other literature.
ii. The items have not been misused or abused in any manner, nor have repairs been attempted
thereon without EdgeTech Customer Service's approval.
iii. Written notice of the failure within the warranty period is forwarded to the Seller, and the
directions received for properly identifying items returned under warranty are followed.
iv. The return notice authorizes the Seller to examine and disassemble returned products to the
extent Seller deems necessary to ascertain the cause for failure.
The warranties expressed herein are exclusive. There are no other warranties, either expressed or implied,
beyond those set forth herein. The Seller does not assume any other obligation or liability in connection
with the sale or use of said products. Any product or service repaired under this warranty shall only be
warranted for the remaining portion of the original warranty period.
Equipment not manufactured by EdgeTech is supported only to the extent of the original manufacturer's
warranties.

vii
RETURNED MATERIAL AUTHORIZATION
Prior to returning any equipment to EdgeTech, a Returned Material
Authorization (RMA) Number must be obtained from CUSTOMER SERVICE.
RMA Purpose
The RMA Number identifies returned equipment when it arrives at our receiving dock and enables tracking
while at our facility. Refer to the RMA number on all documentation and correspondences.
All returned materials must be shipped prepaid. Freight collect shipments will not be accepted. All
equipment should be adequately insured for shipping, but equipment belonging to EdgeTech must be
insured for full value.
If there is more than one item per consignment, include a packing with the shipment. An invoice can
double as a packing slip only when the contents are clearly numbered and identified on the invoice.
CAUTION! Never attempt to ship a Portable Topside in its Storm CaseTM
alone. Although rugged, these cases are not shipping containers, and the
delicate internal components could be damaged. Shipping in this manner
will void any warranties.
NOTE: All shipping charges shall be the customer's responsibility, unless
under warranty, as EdgeTech will pay for return shipping.
NOTE: For International Shipments valued over $1000, the following
Shipper's oath must be sent with the invoice.
Shipper’s Oath:
"I, ______________________________, declare that the articles herein specified are the growth,
produce, or manufacture of the United States; that they were exported from the United States
from the port of _____________________, on or about _______________; that they are returned without
having been advanced in value or improved in condition by any process of manufacture or any
other means; and that no drawback, or allowance has been paid or admitted hereof."
Signed ______________________________

viii
8011M ACOUSTIC DECK UNIT 0004811_REV_F
CUSTOMER SERVICE
Customer service personnel at EdgeTech are always eager to hear from users of our products. Your
feedback is welcome and a valuable source of information that we use to improve these products
continually. Therefore, we encourage you to contact EdgeTech Customer Service to offer any suggestions
or to request technical support:
NOTE: Please have your system Serial Number available when contacting
Customer Service.
E-mail: [e-mail]
Mail: 4 Little Brook Road
West Wareham, MA 02576
Telephone: [phone]
Facsimile: [phone]
24-Hour Emergency
Technical Support Line: [phone]
For more information, please go to www.EdgeTech.com.

ix
COMPANY BACKGROUND
EdgeTech (formerly EG&G Marine Instruments) traces its history in Underwater Data Acquisition and
Processing back to 1966. EdgeTech has designed, developed, and manufactured products, instruments,
and systems — for the acquisition of underwater data, including marine, estuarine, and coastal
applications — for over 50 years.
EdgeTech responds to the needs of the Scientific, Naval, and Offshore communities by providing industry-
leading equipment — such as Sub-Bottom Profilers, Side Scan Sonar, Acoustic Releases, USBL Positioning
Systems, and Bathymetric Systems — that have become standards in the industry.
EdgeTech consistently anticipates and responds to future needs with an active Research and Development
Program. Current efforts are focused on adapting new cutting-edge acoustic technology.

x
8011M ACOUSTIC DECK UNIT 0004811_REV_F
TABLE OF CONTENTS
ATTENTION – READ THIS FIRST! .......................................................................................................... iii
Warnings, Cautions, and Notes................................................................................................................ iii
HARDWARE VARIATIONS AND COMPATIBILITY................................................................................... iv
ABOUT THIS DOCUMENT ..................................................................................................................... v
Purpose of this Manual ............................................................................................................................. v
Liability ...................................................................................................................................................... v
Revision History ........................................................................................................................................ v
WARRANTY STATEMENT..................................................................................................................... vi
RETURNED MATERIAL AUTHORIZATION............................................................................................. vii
RMA Purpose .......................................................................................................................................... vii
CUSTOMER SERVICE.......................................................................................................................... viii
COMPANY BACKGROUND ................................................................................................................... ix
TABLE OF CONTENTS............................................................................................................................ x
List of FIGURES................................................................................................................................... xii
LIST OF TABLES ..................................................................................................................................xiii
SECTION 1: OVERVIEW...................................................................................................................... 1-1
1.1 Standard Package.............................................................................................................................1-1
SECTION 2: SPECIFICATIONS.............................................................................................................. 2-4
2.1 8011M Deck Box Mechanical Specifications....................................................................................2-4
2.2 8012M Transducer ...........................................................................................................................2-5
2.2.1 8012M Transducer Mechanical Specifications .........................................................................2-5
2.2.2 Serial Cable Pin Out................................................................................................................... 2-5
2.2.3 Auxiliary Cable Pin Out..............................................................................................................2-5
SECTION 3: SETUP AND ACTIVATION................................................................................................. 3-6
3.1 8011M Setup....................................................................................................................................3-6
3.1.1 8011M Connector .....................................................................................................................3-8
3.1.2 Legacy 8011M Connector .........................................................................................................3-8
3.2 8011M Battery .................................................................................................................................3-9
SECTION 4: OPERATION .................................................................................................................. 4-10
4.1.1 Keypad Descriptions................................................................................................................4-10

xi
4.1.1.1 Function Keys ...................................................................................................................4-11
4.2 Quick-Start Operation Instructions................................................................................................4-12
4.2.1 Sending Commands (<CMD>) .................................................................................................4-12
4.2.2 Ranging (<RNG>) .....................................................................................................................4-14
4.3 Detailed Operating Instructions.....................................................................................................4-16
4.3.1 Menu (<MENU>) .....................................................................................................................4-16
4.3.1.1 Command Setup...............................................................................................................4-16
4.3.1.2 Range Setup .....................................................................................................................4-16
4.3.2 Commands <CMD> .................................................................................................................4-17
4.3.3 Ranging <RNG> .......................................................................................................................4-18
4.3.4 Serial Port Operations.............................................................................................................4-18
4.3.4.1 Host Mode........................................................................................................................4-19
4.3.4.2 8011M Host Mode Serial Commands ..............................................................................4-20
SECTION 5: MAINTENANCE ............................................................................................................. 5-21
5.1 Basic Maintenance .........................................................................................................................5-21
5.1.1 8011M Deck Unit ....................................................................................................................5-21
5.1.2 Transducer ..............................................................................................................................5-21
5.1.3 Battery Storage .......................................................................................................................5-21
5.1.3.1 Battery Pack Storage Guidelines......................................................................................5-23
SECTION 6: APPENDIX ..................................................................................................................... 6-24
A.1 Sending Benthos Commands ........................................................................................................6-24
A.1.1 Instructions.............................................................................................................................6-24

xii
8011M ACOUSTIC DECK UNIT 0004811_REV_F
LIST OF FIGURES
Figure 1-1: The 8011M Deck Unit .............................................................................................................. 1-2
Figure 1-2: 8012M Transducer................................................................................................................... 1-3
Figure 3-1: 8011M Opened Deck Unit ....................................................................................................... 3-6
Figure 3-2: 8012M Transducer Installed into the 8011M Deck Unit ......................................................... 3-7
Figure 4-1: Image of Keypad .................................................................................................................... 4-10
Figure 5-1: The Screw Locations in the Front Panel................................................................................. 5-22
Figure 5-2: The Front Panel Removed from the Pelican Case ................................................................. 5-22
Figure 5-3: The Battery Connector Location at JP9 ................................................................................. 5-23
Figure 5-4: Uninstall the Battery by Removing the Screws in the Stand-offs.........................................5-23
Figure 6-1: 8011M Benthos Instructions- 8011M Command Menu........................................................6-24
Figure 6-2: 8011M Benthos Instructions- Benthos Mode Selection........................................................ 6-25
Figure 6-3: 8011M Benthos Instructions- Return to Command Menu....................................................6-25
Figure 6-4: 8011M Benthos Instructions- IN BAND Frequency Display................................................... 6-25
Figure 6-5: 8011M Benthos Instructions- IN BAND Frequency Change ..................................................6-26
Figure 6-6: 8011M Benthos Instructions- REPETITION RATE Code Display ............................................. 6-27
Figure 6-7: 8011M Benthos Instruction- Setting REPETITION RATE code ...............................................6-27
Figure 6-8: 8011M Benthos Instructions- IN BAND Frequency and REPETITION CODE Display..............6-29

xiii
LIST OF TABLES
Table 2-1: 8011M Deck Unit Mechanical Specifications............................................................................ 2-4
Table 2-2: 8012M Transducer Mechanical Specifications ......................................................................... 2-5
Table 2-3: Serial Cable Pin Out Descriptions.............................................................................................. 2-5
Table 2-4: Auxiliary Cable Pin Out Descriptions......................................................................................... 2-5
Table 3-1: Current 8011M Amphenol Connector Transducer Connection................................................ 3-8
Table 3-2: Legacy 8011M Spirit Type Connector Transducer Connections ............................................... 3-8
Table 3-3: Front Panel LED Colors and Descriptions.................................................................................. 3-9
Table 4-1: Keypad Functional Key Descriptions ....................................................................................... 4-11
Table 4-2: Keypad Function Adjustment Key Descriptions ...................................................................... 4-11
Table 4-3: Important 8011M Host Mode Symbols and their Meanings ..................................................4-19
Table 4-4: Host Mode Examples .............................................................................................................. 4-20
Table 4-5: Host Mode Serial Commands ................................................................................................. 4-20
Table 6-1: 8011M Benthos Instructions- Example of In-Band Codes and Frequencies........................... 6-26
Table 6-2: 8011M Benthos Instructions- Example of Repetition Codes and Rates .................................6-28

1-1
SECTION 1: OVERVIEW
EdgeTech’s 8011M Acoustic Deck Unit Transceiver is a portable, rugged topside capable of sending and
receiving messages to a deployed system, such as acoustic release units, offered separately.
The 8011M is the most versatile acoustic command-ranging deck unit available. This system can control
and range on EdgeTech’s full line of acoustic releases and other manufacturers’ equipment. For more
information on Configuring the 8011M with non-EdgeTech products, refer to the DETAILED OPERATING
INSTRUCTIONS section of the manual.The 8011M’s features include auto-switching between 115 and 230
VAC and an internal self-charging battery. In addition, the serial and auxiliary ports allow for simple
interfacing with other onboard equipment.
1.1 Standard Package
The 8011M Deck Box comes standard with:
•Set of headphones
•Spare connector for the auxiliary port
•8012M transducer (to drop off the side of a vessel to transmit and receive acoustic signals)
CAUTION! The 8011M Deck Unit is somewhat splash-resistant but not
waterproof. It is not intended to be subjected to seawater or spray.

1-2
8011M ACOUSTIC DECK UNIT 0004811_REV_F
Figure 1-1: The 8011M Deck Unit

1-3
Figure 1-2: 8012M Transducer

2-4
8011M ACOUSTIC DECK UNIT 0004811_REV_F
SECTION 2: SPECIFICATIONS
The specifications for the 8011M Deck Unit and 8012M Transducer are shown in TABLE 2-1 and TABLE 2-2:
2.1 8011M Deck Box Mechanical Specifications
The 8011M is the Deck Unit in the system, with mechanical specifications detailed below:
SPECIFICATION
VALUE
Frequencies Interrogate and Reply frequencies select 7.5 to 15 kHz
Transmit 7.5 to 15.0 kHz - Operator adjustable
Receive
7.0 to 15.0 kHz - Operator selectable multiple channels
Transmit source level 192 dB re 1 micro-Pascal at 1 meter - Controllable by the operator
Receive sensitivity 80 dB re 1 micro-Pascal
Transmit pulse width 10/20 milliseconds
Timing accuracy 0.1 millisecond
Range units Meters and Seconds
Command codes EdgeTech, ORE Offshore, EG&G, Legacy Benthos, Oceano, MORS, and
URI
Status receive Automatic timeline display of acoustic status replies
Beeper Audio confirmation of received signals
Case
Sealed, portable, polyethylene
Size
40.6 cm x 33 cm x 17.3 cm (16 in. x 13 in. x 6.8 in.)
Weight
7.3 kg (16.0 lbs)
Table 2-1: 8011M Deck Unit Mechanical Specifications

2-5
2.2 8012M Transducer
The 8012M is the Transducer in the system. This transducer is used to communicate commands sent from
the 8011M Deck Unit to EdgeTech or other manufacturers' equipment.
2.2.1 8012M Transducer Mechanical Specifications
SPECIFICATION
VALUE
Acoustic frequency
7.5 to 15 kHz
Beam pattern
Omni-directional in the lower hemisphere
Cable length
67 meters (220 feet)
Weight in air
10 kg (22 lbs) including cable
Size
Diameter 11.4 cm (4.5 in); height 10 cm (4.0 in)
Table 2-2: 8012M Transducer Mechanical Specifications
2.2.2 Serial Cable Pin Out
DB9
AMP
DB9 pin 2
AMP pin 8
DB9 pin 3
AMP pin 7
DB9 pin 5
AMP pin 2
Table 2-3: Serial Cable Pin Out Descriptions
2.2.3 Auxiliary Cable Pin Out
PIN
DESCRIPTION
Pin 1
Ground
Pin 2
TX transmit envelope goes negative at the beginning of the transmit pulse.
Pin 3
Detect goes high on detecting a valid reply pulse. This signal is delayed by 11 milliseconds from the
actual detection.
Pin 4
Trigger If the deck unit is in the ranging mode. A positive edge in on this pin will initiate a ranging
operation.
The auxiliary port is 5-volt logic.
Table 2-4: Auxiliary Cable Pin Out Descriptions

3-6
8011M ACOUSTIC DECK UNIT 0004811_REV_F
SECTION 3: SETUP AND ACTIVATION
3.1 8011M Setup
To set up the 8011M:
1. Plug the 8011M into a power source.
2. Open the deck unit by unlatching the cover of the deck unit.
Figure 3-1: 8011M Opened Deck Unit

3-7
3. Attach the Model 8012M transducer to the TRANSDUCER connector. It should be fully threaded
and finger tightened.
Note: The user may need to apply pressure to the connector's back while
tightening the locking sleeve.
Figure 3-2: 8012M Transducer Installed into the 8011M Deck Unit