Edgewater Networks 262CX User manual

262CX

1
262CX SPECIFICATIONS
CE
10 PERSONS OR 1150KG
925KW MAX POWER
B RATING
LENGTH
26’ 5”
(8.2m)
BEAM
9’ 3”
2.8m
DRAFT (BOAT ONLY)
21”
(53.3cm)
BOAT WEIGHT
5000lbs
2268kg
WEIGHT CAPACITY
4000lbs
(1816kg)
PERSON CAPACITY
12
PERSON WEIGHT
1980lbs
(900kg)
FUEL CAPACITY
163gal
(617L)
TRANSOM HEIGHT
Twin-25”
MAX POWER
500hp
(375kw)
COCKPIT DEPTH
27”
69cm
COCKPIT AREA
89sq.ft.
8.3m2
LENGTH ON TRAILER
33’
10m
BRIDGE CLEARANCE
W/ T-TOP
8’ 9”
(2.4m)
FLOTATION
UNSINKABLE/Level

2
Dear EdgeWater 262CX owner:
Congratulations on purchasing one of the finest small boats ever built. It has been constructed with
care from the finest available materials. At EdgeWater we take great pride in the quality and
craftsmanship that goes into each boat, large or small. We believe you’ll have many years of
enjoyment from your new EdgeWater and thank you f or entrusting your leisure time to one of our fine
products.
This manual has been assembled to help you learn more about your new boat and increase your
enjoyment of it. Your EdgeWater has been built for a “Lifetime on the Water”.
Boat safe and boat smart, we wish you many years of boating pleasure.
Sincerely,
Jennifer Butera, President
EdgeWater Powerboats

i
Customer Name
Address
City
State
Zip
Phone ( )
Email
Dealer Name
Address
City
State
Zip
Phone ( )
Fax
Purchase Date
Delivery Date
Engine Make
Model
Serial No.
Engine Make
Model
Serial No.
Engine Make
Model
Serial No.
Hull Number
Ignition Key #
Service Information
EdgeWater Power Boats LLC reserves the right to make
alterations in the standard and optional equipment without
incurring obligation to those boats already having been built.
Every effort has been made to ensure that the information in
this manual accurately describes vessels being built at the date
of printing.

ii

iii
Table of Contents
1/ General Information....................................................................................................1
1.1 General.......................................................................................................................................1
1.2 Owner / Operator Responsibilities.................................................................................1
Registration.......................................................................................................................................................1
Reporting Boating Accidents......................................................................................................................1
Education............................................................................................................................................................1
Required Equipment......................................................................................................................................1
2/ Helm Control Systems .................................................................................................2
2.1 General.......................................................................................................................................2
2.2 Hydraulic Steering System..................................................................................................2
General ................................................................................................................................................................2
Steering System Maintenance....................................................................................................................2
2.3 Engine Throttle and Shift Controls ..................................................................................2
Engine Stop Switch.........................................................................................................................................3
3/ Propulsion System........................................................................................................4
3.1 General.......................................................................................................................................4
3.2 Engine Cooling System .........................................................................................................4
3.3 Propellers .................................................................................................................................5
Understanding Propeller Pitch..................................................................................................................5
3.4 Engine Power Tilt and Trim...............................................................................................5
3.5 Engine Instrumentation ......................................................................................................6
Tachometer........................................................................................................................................................6
Speedometer.....................................................................................................................................................6
Temperature Gauge .......................................................................................................................................6
Fuel Gauge..........................................................................................................................................................7
Voltmeter............................................................................................................................................................7
Hour Meter.........................................................................................................................................................7
Engine Alarms ..................................................................................................................................................7
Compass..............................................................................................................................................................7
Instrument Maintenance..............................................................................................................................8
4/ Fuel Systems ...................................................................................................................9
4.1 General.......................................................................................................................................9
4.2 Fuel Fill ......................................................................................................................................9
4.3 Fuel Vent ...................................................................................................................................9
4.4 Fueling .......................................................................................................................................9
Green Tank Effect.........................................................................................................................................10
4.5 Fuel System Maintenance ................................................................................................ 10
4.6 Fuel Filters............................................................................................................................. 10
5/ Electrical Systems...................................................................................................... 11
5.1 General.................................................................................................................................... 11
5.2 Automatic Charging Relay System ................................................................................ 11
Battery Zones.................................................................................................................................................11
5.3 Panel Switches ..................................................................................................................... 11
5.4 Electrical System Maintenance ...................................................................................... 12
6/ Raw Water and Freshwater Systems .................................................................. 13

iv
6.1 General.................................................................................................................................... 13
6.2 Livewell Operation ............................................................................................................. 13
6.3 High Pressure Washdown................................................................................................ 13
6.4 Freshwater System............................................................................................................. 13
Operating Instructions for the freshwater system.........................................................................14
Troubleshooting Water Systems ...........................................................................................................14
6.5 Raw Water System Maintenance ................................................................................... 14
7/ Drainage System ........................................................................................................ 15
7.1 General.................................................................................................................................... 15
7.2 Drain System Maintenance.............................................................................................. 15
7.3 Cockpit Drains...................................................................................................................... 15
7.4 Transom Bilge ...................................................................................................................... 15
7.5 Locker Drains ....................................................................................................................... 16
7.6 Aft Fishboxes ........................................................................................................................ 16
7.7 T-Top Drain........................................................................................................................... 16
8/ Safety Equipment....................................................................................................... 17
8.1 Required Safety Equipment ............................................................................................ 17
Personal Floatation Devices (PFD’s)....................................................................................................17
Visual Distress Signals ...............................................................................................................................17
Pyrotechnic Visual Distress Signals......................................................................................................17
Sound Signaling Device..............................................................................................................................17
Navigation Lights .........................................................................................................................................17
Fire Extinguisher..........................................................................................................................................17
8.2 Suggested Safety Equipment –Inshore ....................................................................... 18
8.3 Suggested Safety Equipment –Offshore ..................................................................... 18
9/ Safe Operation ...............................................................................................................2
9.1 Pre-Cruise Check ListS .........................................................................................................2
Before Starting the Engine ..........................................................................................................................2
After Starting the Engine .............................................................................................................................2
9.2 basic rules of the road..........................................................................................................3
Aids to Navigation...........................................................................................................................................3
9.3 Safe operation .........................................................................................................................3
Getting Underway...........................................................................................................................................3
9.4 towing or being towed .........................................................................................................4
9.5 stopping the boat ...................................................................................................................5
9.6 Docking......................................................................................................................................5
9.7 after operation........................................................................................................................5
9.8 trailering your boat...............................................................................................................6
Before Trailering the Boat...........................................................................................................................6
Trailering Tips..................................................................................................................................................6
Reversing the Trailer.....................................................................................................................................6
9.9 Launching Your boat.............................................................................................................7
9.10 retrieving your Boat..............................................................................................................7
10/ Routine Maintenance ..................................................................................................8
10.1 exterior Hull and deck .........................................................................................................8
Fiberglass ...........................................................................................................................................................8
Stainless Steel Hardware .............................................................................................................................8
Anodized Aluminum ......................................................................................................................................8

v
Chrome Hardware ..........................................................................................................................................8
Plexiglas ®.........................................................................................................................................................8
Upholstery..........................................................................................................................................................9
Sump Area..........................................................................................................................................................9
Powder Coated Parts .....................................................................................................................................9
10.2 Engine.........................................................................................................................................9
11/ Exterior Equipment .................................................................................................. 10
11.1 Anchor Locker...................................................................................................................... 10
11.2 Boarding Ladder.................................................................................................................. 10
11.3 trim Tabs................................................................................................................................ 10
12/ Seasonal Maintenance.............................................................................................. 11
12.1 engine...................................................................................................................................... 11
12.2 Hull........................................................................................................................................... 11
12.3 storage .................................................................................................................................... 11
12.4 trailer ...................................................................................................................................... 11

1
1/ General Information
1.1 GENERAL
Your boat is equipped with twin outboard engines.
Each outboard manufacturer provides manuals, which details the operation and
maintenance procedures of their products. Please read and observe the instructions set
forth in the outboard manual.
1.2 OWNER / OPERATOR RESPONSIBILITIES
Registration
It is important that you register your boat. Federal law requires that all powered,
undocumented vessels be registered in their state of principal use. Contact the
appropriate agency in your local state to obtain specific registration information.
Reporting Boating Accidents
All boating accidents must be reported to the proper authorities in the state of which the
accident occurred. If someone dies or disappears as a result of the recreational boating
accident, it must be reported immediately, with a formal report made within 48 hours. If
there is damage of more than $500, or if the boat is lost, a formal report must be made
within 10 days.
Questions regarding accidents should be directed to the Boating Safety Hotline, (800)
368-5647.
Education
Attending a Boating Education Course will be beneficial for all boaters, experienced or
not. If you are new to boating, this course will be the best and safest way to begin your
life on the water. Some states require that all boaters obtain a boating safety card (also
known as a “boating license”), which is required before the operation of any vessel.
Required Equipment
The United States Coast Guard requires certain equipment to be carried aboard each
boat. In addition, they set minimum safety standards. These standards apply to the boat
itself, and detail specific equipment that must be carried aboard to ensure proper boater
safety.
SOME STATES AND LOCAL AGENCIES REQUIRE EQUIPMENT
THAT IS NOT REQUIRED BY THE U.S. COAST GUARD. YOUR
LOCAL AGENCY OR DEALER CAN PROVIDE SPECIFIC
INFORMATION REGARDING THESE NON-STANDARD
REQUIREMENTS.

2
2/ Helm Control Systems
2.1 GENERAL
The helm station contains the controls and monitors for the boat. The main control
systems include the engine throttle and shift controls, the steering system, and the trim
tab controls. These provide the operator with the ability to control speed, direction, boat
trim, and attitude. Because these systems are manufactured separately, each
manufacturer provides separate manuals that include the operation and use of their
system. We have included some general information of each system for quick access
below.
2.2 HYDRAULIC STEERING SYSTEM
General
Your boat is equipped with hydraulic steering. This system uses hydraulic fluid to change
the position of the outboard motors, and thus steer the boat. This hydraulic system may
include power assist pumps, similar to the operation of the power steering in your car.
The SeaStar ® helm pump is an axial piston pump. It has a built-in lock valve to prevent
the steering load of the engines from feeding back to the boat operator. Please review
the hydraulic steering diagram in the appendix of this manual for a visual representation
of this system. In the event of a power assist failure, the steering system will still function
normally but in a manual mode, which requires greater steering effort by the operator.
While running at slow speeds, your boat may tend to wander slightly back and forth. By
keeping the wheel in the center without overcompensating for the slight wandering will
prevent over-steering, and will also reduce the boat’s tendency to wander.
Steering System Maintenance
Routine system inspection should occur regularly. Cables, hoses, linkages, and helm
assemblies should be inspected for wear, corrosion, cracking, or deterioration. Cleaning
and light grease should be applied to all exposed metal parts. All damaged or
deteriorated parts should be replaced immediately.
Cleaning fluids containing ammonia, acids, or any other corrosive ingredients must not
be used for cleaning any part of the steering system. Failure to comply will cause serious
damage to the system, which could result in an accident or injury.
2.3 ENGINE THROTTLE AND SHIFT CONTROLS
For full information on the Yamaha Outboards installed on your boat, consult the
Yamaha engine manual.
Your boat is equipped with twin engines. These advanced engines utilize Yamaha’s
electronic digital engine control, which allows for automated synchronization and
operation of their outboard motors. With this system, there are no cables, and no
required manual adjustments.

3
By moving the handles of the throttle control forward and backwards, the operator
controls the engine speed, and thus the speed of the boat. Careful use of the controls
provides smooth, responsive, and safe operation of the boat.
DO NOT BRING THE THROTTLE BACK ABRUPTLY TO STOP THE
BOAT UNLESS IT IS AN EMERGENCY. ALLOW TIME FOR THE
ENGINE RPM TO COME TO IDLE BEFORE SHIFTING TO REVERSE.
IMPROPER SHIFTING MAY RESULT IN MAJOR ENGINE OR
GEARBOX DAMAGE. PLEASE REFER TO YOUR ENGINE OWNER’S
MANUAL FOR FURTHER OPERATIONAL PROCEDURES FOR
YOUR OUTBOARD.
Engine Stop Switch
The engine stop switch is designed to stop the engines in the event that the operator
falls overboard. The operator should always wear the engine stop switch lanyard while
the boat is in motion. Pulling the lanyard from the control will stop all engines. If the
engines will not start properly, the lanyard may not be properly attached to the engine
stop switch.
DO NOT USE THE ENGINE STOP SWITCH TO TURN OFF THE
ENGINES UNLESS IT IS AN EMERGENCY. THIS MAY IMPAIR YOUR
ABILITY TO QUICKLY RE-START THE ENGINE, AND MAY CAUSE
DAMAGE TO THE ENGINE STOP SWITCH.
EACH IGNITION KEY HAS A 3-DIGIT NUMBER STAMPED ON IT.
PLEASE RECORD THIS NUMBER FOR FUTURE REFERENCE ON
THE SERVICE INFORMATION PAGE IN THE FRONT OF THIS
MANUAL.

4
3/ Propulsion System
3.1 GENERAL
Your boat is powered by twin engines. These modern outboards are four-stroke engines
that operate similarly to those found in your car. While these engines do not consume oil
like older two-stroke models, it is important to check the oil level using the dipstick before
each day’s run.
NEVER USE TWO-STROKE TC-W3 OIL IN A FOUR-STROKE
ENGINE.
ALWAYS USE THE MANUFACTURER’S RECOMMENDATIONS FOR
OIL CHANGE INTERVALS, AND ALWAYS USE THE
RECOMMENDED OIL TYPES FOR YOUR ENGINE.
DON’T ATTEMPT TO SERVICE YOUR OUTBOARD OR ANY OF ITS
COMPONENTS UNLESS YOU ARE FAMILIAR WITH ITS
OPERATION AND DANGERS. MANY OF THE MOVING PARTS ARE
EXPOSED AND CAN POSE EXTREME DANGER TO ANYONE
UNFAMILIAR WITH THEIR OPERATION. ALWAYS LEAVE ALL
ENGINE SERVICE TO A QUALIFIED TECHNICIAN.
Each manufacturer provides manuals to assist in the proper operation and maintenance
of their outboard engines. Follow the guidance and schedules for proper operation of the
outboard engines. Modern outboards require very few maintenance procedures,
however, it is crucial that they be performed in accordance with the manufacturer’s
recommendations to extend engine life. If the boat is to be kept in saltwater for an
extended period, always tilt the outboards as high out of the water as possible. This will
decrease the possibility of marine growth on the outside of the engines, and will reduce
blockages of the cooling water ports, which could cause engine overheating.
YAMAHA OUTBOARDS ARE PAINTED WITH A HIGHLY COMPLEX
PROCESS TO ALLOW THE ENGINE TO PERFORM IN A MARINE
ENVIRONMENT. NEVER PAINT YOUR OUTBOARD’S LOWER UNIT.
SOME MARINE PAINTS, SUCH AS BOTTOM PAINTS WILL CAUSE
SEVERE ENGINE DAMAGE.
ALWAYS RETURN ALL WARRANTY CARDS FOR YOUR BOAT,
ENGINE, AND RELATED ITEMS. THEY ARE REQUIRED IN THE
EVENT THAT YOU HAVE A WARRANTY PROBLEM.
DO NOT RUN YOUR OUTBOARD WITHOUT WATER COMING INTO
THE LOWER UNIT. THE WATER PUMP IMPELLER CAN BE
DAMAGED IN ONLY SECONDS WHEN RUN WITHOUT WATER.
ALWAYS USE THE FLUSH PORT ON THE ENGINE WHEN RUNNING
THE ENGINE OUT OF THE WATER.
3.2 ENGINE COOLING SYSTEM
The engines installed on your boat are cooled by raw water taken in through ports in the
lower part of the drive section. Make sure that these ports are free of debris or other
items that might cause the flow to be restricted. Outboard engines have check streams
that spray water when the engine is running to indicate proper cooling. It is important to

5
periodically check the streams for a steady flow of water. If water does not flow, shut off
the engine as this could indicate a problem with your cooling system, which will cause
engine damage if left ignored. Be especially watchful during navigation of shallow waters
as the intake ports can easily become clogged with weeds, dirt, or other debris.
3.3 PROPELLERS
Your boat uses propellers to move through the water. The propeller should always be
clean and free of damage, which adversely affects its performance. Your dealer can
assist you in the proper selection of a propeller for your boat. This selection is based on
the horsepower of the engine and its relationship to the size and weight of the boat.
Different propeller selections can dramatically affect the performance and fuel economy
of your boat.
Understanding Propeller Pitch
Two numbers determine propeller sizes. The first number denotes the diameter of the
propeller and the second denotes the pitch. Variations of these numbers changes the
load of the engine, as well as the strength of the propeller to “hold” water without
slipping.
With a larger number, you increase the theoretical movement of the boat, but also the
load on the engine. With an optimized propeller, the engine should be able to reach its
maximum operating RPM range at wide-open throttle (WOT) and full trim. High pitch
propeller selections may not allow the engine to reach this speed, and may
unnecessarily strain the engine. Low pitch propeller selections in which the engine
exceeds its maximum speed may increase engine wear, and decrease fuel economy.
IF YOUR BOAT CAME FROM THE FACTORY WITH A PROPELLER
SELECTED BY EDGEWATER AND YAMAHA ENGINEERING, IT
WILL BE ALREADY OPTIMIZED FOR YOUR PARTICULAR BOAT.
BEFORE CHANGING THE PITCH OR DIAMETER OF YOUR
PROPELLER, ALWAYS CHECK WITH YOUR DEALER TO
DETERMINE HOW THE CHANGES WILL AFFECT YOUR BOAT AND
ENGINE PERFORMANCE. CERTAIN MODIFICATIONS AFFECT
WEIGHT BALANCE AND/OR WIND RESISTANCE MAY REQUIRE A
PROPELLER CHANGE. ALWAYS CHECK WITH YOUR DEALER
FIRST IF OPTIMUM RPM CANNOT BE ATTAINED.
3.4 ENGINE POWER TILT AND TRIM
The power tilt and trim system on your outboard provides the operator with the freedom
to change the running angle of your boat, and to accommodate for variable load and sea
conditions. Moving the outboard lower unit towards the transom is referred to as
trimming “in” while moving the outboard lower unit away from the transom is referred to
as trimming “out”. The trim and tilt controls are located on the throttle levers located at
the helm.
It is best to trim the engines in for best acceleration from displacement to planning mode.
This will help bring the bow down and reduce the power needed to bring the boat onto
plane. Once on plane, the engine can be trimmed “out” which will reduce engine load,
and increase fuel economy. When operating the boat is shallow waters, you may need to
tilt the engines out of the water to reduce damage.

6
While running under normal conditions, the bow should be in a 3º to 5º upwards angle to
maximize the hull’s ride and performance. When sea conditions are rougher than
normal, using engine trim to bring the bow slightly down will help to improve boat ride,
and plane at lower speeds.
When storing or transporting your boat, always tilt the engines out of the water, using the
tilt controls at the helm, or the engine tilt controls located on the side of the outboard
engine.
3.5 ENGINE INSTRUMENTATION
Your boat is equipped with Yamaha’s digital engine system, which displays all traditional
gauge readings, as well as engine diagnostics and warnings. With this system, one
display can show readings from what would normally be many gauges.
IF YOU ARE NOT FAMILIAR WITH THE YAMAHA DIGITAL ENGINE
SYSTEM, IT IS HIGHLY RECOMMENDED TO READ THE YAMAHA
ENGINE MANUAL FOR ADDITIONAL INFORMATION.
Tachometer
The tachometer displays the number of revolutions per minute (RPM) that the engine is
turning. It is important to become familiar with the operating range of your engine and its
operating characteristics. By monitoring the engine speed on the tachometer display, the
operator can make adjustments to accommodate for changing sea conditions. The
tachometer is also extremely helpful for troubleshooting engine problems.
Speedometer
The speedometer indicates the boat’s speed. Your boat uses a pitot tube system to
determine engine speed. This system uses water pressure across a tube mounted on
the transom of your boat to determine engine speed. In the event that erroneous speed-
readings appear, it is likely caused by debris clogging the pitot tube. If this is the case,
contact your dealer, as your pitot tube will need to be cleaned.
It is important for the operator to monitor the boat speed at all times in relation to the sea
conditions. Your boat is designed to plane and cruise at specific speeds, and monitoring
the speedometer will help optimize the performance and fuel economy of your boat.
Temperature Gauge
Your digital engine display shows the temperature of the engines while running. Sudden
variations in engine temperature can cause major engine damage if left ignored. Your
digital engine display will display a warning if the engine temperatures become
excessive, however it is best to monitor engine temperature as well.
MAJOR ENGINE DAMAGE CAN RESULT FROM EXCESSIVE
ENGINE TEMPERATURES. IF THE ENGINE TEMPERATURE
BECOMES EXCESSIVE, OR THE DIGITAL ENGINE DISPLAY
SHOWS A WARNING, IMMEDIATELY SHUT OFF THE ENGINES
AND CHECK THE COOLING SYSTEM FOR OBSTRUCTIONS
BEFORE RESUMING OPERATION.

7
Fuel Gauge
Your digital engine display shows the current fuel level of the boat. To ensure the safest
boating, always follow the rule of thirds.
Use 1/3 of your fuel to get to your destination.
Use 1/3 of your fuel to return
Leave 1/3 of your fuel in reserve.
This system ensures that your boat has enough fuel in reserve to accommodate for
emergencies that would change your initial boat plan, and will keep your boat from
running out of fuel on the water.
It is important to “calibrate” your fuel gauge during your first initial boat trip. Your fuel
tank is not square, and thus a ½ tank gauge reading may only indicate 1/3 of a tank in
reality. By understanding the correct fuel level for gauge readings, you will more
accurately know the amount of fuel in your tank at any time.
THIS GAUGE IS A MEASURE OF RELATIVE FUEL SUPPLY AND IS
NOT A CALIBRATED INSTRUMENT. ALWAYS LEAVE FUEL IN
RESERVE FOR EMERGENCIES.
Voltmeter
This meter displays the voltage for the battery and charging system, and is incorporated
in the Yamaha digital engine display. The voltmeter should read at least 12.1 volts when
the engines are off, and 13.4 volts when the engines are running. An excessively low or
high voltage reading indicates a problem with your boat’s charging system.
Hour Meter
Unlike cars, where maintenance is done based on mileage, your boat’s service schedule
is based on engine hours. The Yamaha digital engine display incorporates an hour
meter to accurately perform maintenance procedures on schedule.
Engine Alarms
The outboard engines are equipped with several audible engine alarms, as well as
safety modes to reduce the risk of engine damage. Refer to the Yamaha outboard
engine manual for more information of these warnings and alarms.
IF AN ENGINE ALARM SOUNDS, SHUT DOWN THE ENGINE UNTIL
THE SOURCE OF THE PROBLEM IS DETERMINED. MAJOR
ENGINE DAMAGE CAN RESULT IF ALARMS ARE LEFT IGNORED.
Compass
Even with modern GPS systems, a compass is an essential tool for navigation. Not only
does a compass help boaters accurately keep and hold a heading, but it can be used
even if your entire electronics system fails, which can help a boater head for land even
when offshore. Your compass is designed to accurately point towards magnetic north,
which is slightly different than true north. Therefore, you may need to adjust your
compass in order to accurately use it with your paper charts. Please refer to your
compass manual for details.

8
Instrument Maintenance
Your instrument panel should be periodically cleaned to keep it free of salt and
atmospheric debris. The ignition switches should be periodically sprayed with a contact
cleaner/lubricant to keep them free of corrosion and dirt. Cleaners with abrasives or
harsh chemicals should never be used on gauges and displays. Always refer to the
individual manuals for specific cleaning procedures.

9
4/ Fuel Systems
4.1 GENERAL
Your boat’s fuel system has been designed to meet the requirements of the United
States Coast Guard, the National Marine Manufacturers Association (NMMA), and the
American boat and Yacht Council (ABYC), which were in effect at the date of
manufacture. While all fuel system components on your boat are tested for functionality,
and are free of leaks, regular inspection and maintenance of these components are the
responsibility of the owner. This will ensure that all components are operating safely and
effectively. Make periodic inspections of all fuel system components to determine if the
system is still safe and free of leaks. Special care should be taken when inspecting joins
and connections to ensure that they have not loosened due to vibration.
IF ANY ODOR OF GASOLINE IS DETECTED, IMMEDIATELY SHUT
OFF ALL ENGINES AND ELECTRICAL DEVICES UNTIL THE
SOURCE AND CONDITION OF THE ODOR HAS BEEN
DETERMINED AND ELIMINATED. ALWAYS HAVE A FIRE
EXTINGUISHER AT THE READY UNTIL THE CONDITION HAS BEEN
RESOLVED.
4.2 FUEL FILL
The fuel fill cap is located on the port side and is labeled “GAS”. Tighten the cap until it is
snug. The gas cap has a built-in vent to allow air to escape while fueling.
4.3 FUEL VENT
According to various safety regulations, all boats must use a vented fuel system. Your
boat is equipped with an external vent, which is active during filling only, as well as a
passive vent. The active fueling vent is incorporated into the fuel fill cap. All other venting
equipment is incorporated into the tank. Make sure that the fill and vent area is kept free
from debris. The vent also allows air expansion and contraction of fuel in the tanks.
DO NOT SMOKE OR INTRODUCE AN OPEN FLAME NEAR THE
FUEL CAP!
4.4 FUELING
Your boat is equipped with a built-in 163-gallon fuel tank. Before fueling, you should
follow these procedures. Your engines are designed to run only on unleaded gasoline.
Make sure that the boat is securely moored and engines are turned off.
Make sure that all switches are off and all cigarettes and open flames are
extinguished.
Know the location of all fire extinguishers.
Remove the fuel fill cap.
Place the nozzle firm against the side of the opening to prevent static discharge.
Begin fueling.
Re-install the fuel cap until it fits snug.

10
Check the bilge area for fuel odors before starting the engine.
NEVER USE FUELS THAT CONTAIN HIGHER THAN 10% ETHANOL.
NEVER USE DIESEL FUEL IN YOUR BOAT; IF USED, THIS WILL
REQUIRE EXTENSIVE FUEL TANK AND ENGINE CLEANING.
ETHANOL IS CORROSIVE AND ALLOWS MOISTURE TO ENTER
THE FUEL TANK, WHICH CAN CAUSE ENGINE DAMAGE, AND
LOSS OF PERFORMANCE. IT IS RECOMMENDED TO USE A FUEL
STABILIZER (PREFERABLY A MARINE GRADE ONE THAT TREATS
ETHANOL) TO REDUCE THE RISK OF ENGINE DAMAGE.
IF FUEL ODORS ARE DETECTED, DO NOT START THE ENGINE!
IMMEDIATELY CHECK THE FUEL SYSTEM FOR LEAKS BEFORE
STARTING THE ENGINE.
DO NOT FILL THE FUEL TANK WHILE THE ENGINE IS RUNNING.
DO NOT ALLOW SMOKING OR ANY OPEN FLAMES WITHIN 50 FT.
OF THE FUELING AREA. FUEL IS EXTREMELY FLAMMABLE. TO
PREVENT DAMAGE TO THE ENGINE, USE ONLY FUELS WITHOUT
HARSH ADDITIVES OR ALCOHOL. REFER TO YOUR ENGINE
OWNER’S MANUAL FOR SPECIFIC FUEL REQUIREMENTS.
Green Tank Effect
During the initial fuel fill, it may be difficult to fill the boat with fuel. This is known as the
“green tank effect” and is completely normal during the first fill. As fuel is introduced into
the tank, the temperature difference may cause the fuel to expand and vaporize, which
will close the safety valves in the tank. Wait 15 minutes to allow the temperatures to
equalize and then attempt re-fueling the boat.
4.5 FUEL SYSTEM MAINTENANCE
Regularly inspect the fuel system components. All lines, fittings, and bulbs should be
flexible, and all metal components should not be corroded. If fittings or other
components appear cracked or damaged, they must be replaced immediately.
4.6 FUEL FILTERS
Your boat is equipped with fuel filters which are installed in the transom area of your
boat. This type of filter is designed to prevent water from entering your engine. At a
minimum, the filter element should be replaced at the beginning of every boating
season. Always carry a filter wrench and spare filter for your boat. Poor engine
performance may be the result of a blocked, or water filled fuel filter. If you use fuel that
contains ethanol (from a gas station), you may need to replace your fuel filter more
often, as this type of fuel may cause more water to enter the tank.

11
5/ Electrical Systems
5.1 GENERAL
Your boat operates on a 12-volt DC system, similar to those found on cars. However,
your boat uses AGM deep-cycle marine batteries, which differ from the lead-acid type
batteries, found in cars. These high-performance batteries can handle the additional
electrical load and environmental stress required to operate in a marine environment.
Never replace your batteries with automotive style batteries.
Your boat’s electrical system includes all wiring from the engine, helm, and accessories.
An electrical schematic is included in the Appendix of this manual for troubleshooting.
Always use marine grade components when replacing electrical components, as all
other components will deteriorate quickly in a marine environment. As usual, the best
way to ensure that all repairs are done properly is to have them performed only by a
certified dealer or technician.
5.2 AUTOMATIC CHARGING RELAY SYSTEM
Your boat is equipped with an automatic charging relay system, which will automatically
combine your battery zones when the engine is running for charging, and isolate them
when the engines are off. With this system, you will not need to use the battery selector
switch to charge your boat’s batteries.
Battery Zones
Your boat is equipped with three battery zones. Your boat uses a main battery control
switch which will remotely turn on the remote switches (RBS). There is a separate
remote switch (RBS) for each bank. Your boat is also equipped with a Battery Parallel
control switch which will control a remote charging relay switch (ML-ACR). When running
the boat the Parallel switch should be in the AUTO position. The only time the Parallel
switch should be in the combined position is in the event of a low engine cranking
battery. Doing this will combine all 3 banks together allowing you to start the engine.
Once started, return the switch to the auto position. When leaving the boat unattended,
both the battery switch and parallel switch should be in the “OFF” position. In the event
of a failure of the control switch all the remote switches offer manual control. For long
term storage out of the water it is recommended to manually turn the remote switches
off.
AVOID LEAVING THE PARALLEL SWITCH IN THE “COMBINED”
POSITION. THIS CAN CAUSE ALL ZONES TO DISCHARGE,
INCLUDING THE ENGINE BATTERIES.
5.3 PANEL SWITCHES
Your boat is equipped with panel-mounted breakers located at the starboard helm which
encompasses main, 24hr, and circuit breakers. Switches are provided at the helm for
navigation lights, deck lights, spreader lights, helm lights, cabin lights, locker lights, horn,
bilge pumps, livewell, raw water pump, fresh water pump, and one accessory. A wiring
diagram is included with this manual to assist with troubleshooting of the boat’s electrical

12
system. Please note that the accessory circuits are protected by circuit breakers with
various amperage ratings. When installing additional devices, always check the breaker
circuit rating matches the requirement of the device used.
Your boat is equipped with a forward and aft bilge pump and automatic float switch that
is wired directly to the battery circuits so it can pump water out of the bilge even when
the battery control switch is in the “OFF” positions.
5.4 ELECTRICAL SYSTEM MAINTENANCE
At the beginning and end of each season, the exposed electrical components of the
switch panel should be sprayed with a non-conductive rust/corrosion inhibiting spray.
Inspect all wiring for breaks, loose terminals, or other damage. Replace worn or
deteriorated components immediately. The AGM batteries of your boat are maintenance
free, and require only basic cleaning.