EFFILUX RandomDot-000 User manual

RandomDot-000
USER MANUAL
RandomDot-000
ID #016729[C]
Version 1.1.2021
MAJ:10 mai 2021
Please take a while to consider and read this brochure before using your new device.
If you have any doubt, please contact EFFILUX.
•Do not look directly or with any optical instrument the light beam
•IP54 Classification : Protection against dust and water projections from all directions
•Avoid any contact with the LED or with the projection lens
•Use the device in an environment at 0°C to +50°C with no excessive moisture: high humidity and high
temperature could damage the device
•Do not use the device in an environment with oil fumes and steam
•Do never try to fix any damages to the product by yourself
•Make sure you are using a correct power supply before connecting the device
•Do not inverse electrical polarity –check your connections and the conventions before turning on the power
supply
•Make sure you consider an adapted connector to link the device to the power supply
•Make sure you are using a power supply with the 62368 standard for power supplies safety
Any improper use voids the warranty
For all maintenance operation, the product must be switched off.
To handle the optical components, wearing gloves is strongly recommended.
To clean the optical components, use compressed air duster if there is some dust.
User security
Maintenance

RandomDot-000
USER MANUAL
RandomDot-000
ID #016729[C]
Version 1.1.2021
MAJ:10 mai 2021
To remove marks on the lens, wipe 1-2 drops of non-alcohol-based cleaning fluid in a gentle circular motion with a
cleaning tissue. Always apply the fluid to a tissue rather than the lens itself.
The product is supplied with a 24V constant voltage.
Please be careful to use a voltage comprised between 22V and 29V.
OPERATING THE PRODUCT
RandomDot-000 is an industrial white LED pattern projector. It must be used only for projecting its pattern on a
surface, excluding any other use.
The LED driver inside the product is set to automatically pulse the LED.
If you trigger light for a short pulse (< 25 ms), light is pulsed (LED are driven at 2,2A).
If your pulse is longer, the driver automatically decreases LED current to 0,4A (18% of max current) to protect LED
against failure.
Maximum TON = 25 ms
Minimum TOFF = 25 ms
Response rise time : 35 µs
Response fall time : 30 µs
Peak consumption : 44W
Continuous mode consumption : 10W
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference received, including interference that may cause undesired operation
STATUS LED
LED color
Designation
Red
Overtemperature security
Activated when the
temperature of the LED
reaches 75°C
Green
Lighting ON
Blue
TRIG signal IN
Electronical consideration

RandomDot-000
USER MANUAL
RandomDot-000
ID #016729[C]
Version 1.1.2021
MAJ:10 mai 2021
ELECTRONICAL PINOUT
POWER / GPIO –M12 8 PINS MALE CONNECTOR
Pin
number
Cable
color
Contact
arrangement
Designation
Details
IN/OUT
Voltage
Reference
1
White
M12 8 pins
Male
connector
N/C
/
/
2
Brown
+24V
Power IN
IN
0V
3
Green
GPIO_IN2_ROBOT
Optocoupler IN
IN
GPIO_GND
4
Yellow
GPIO_GND
Optocoupler IN
GND
IN
GPIO_GND
5
Grey
GPIO_VCC
Supply for
Optocoupler
Output
IN
Chassis GND
6
Pink
GPIO_OUT1_ISO
Optocoupler OUT
OUT
Chassis GND
7
Blue
0V
0V
IN/OUT
0V
8
Red
GPIO_OUT2_ISO
Optocoupler OUT
OUT
Chassis GND
CAMERA –M12 8 PINS FEMALE CONNECTOR
Pin
number
Cable
color
Contact
arrangement
Designation
Details
IN/OUT
Voltage
Reference
1
White
M12 8 pins
Female
connector
GPIO_OVERTEMP
1 = OK (24V)
0 = NOK (0V)
OUT
Chassis GND
2
Brown
+24V
Power OUT to
camera
OUT
0V
3
Green
GPIO_IN2
Optocoupler OUT
OUT
Chassis GND
4
Yellow
0V
0V
IN/OUT
0V
5
Grey
+24V
GPIO_VCC for
camera
(Supply for
camera
optocouplers)
OUT
0V
6
Pink
GPIO_OUT1
Lighting TRIG
IN
0V
7
Blue
0V
0V
IN/OUT
0V
8
Red
GPIO_OUT2
Input
IN
0V

RandomDot-000
USER MANUAL
RandomDot-000
ID #016729[C]
Version 1.1.2021
MAJ:10 mai 2021
Color Temperature: 6000K
Optical consideration
Mechanical consideration
The product is mounted with the C-mount lens VS
Technology VS-1214H1 in addition to a custom lens made
by EFFILUX.
EFFILUX will deliver the product with the following optical
configuration:
-Horizontal projection angle : 62°
-Vertical projection angle : 48°
-Diagonal projection angle : 75°
The focus and the aperture can be adjusted with manual
settings of the C-mount lens.
The projected pattern is a square random 50%-density cloud of dots
The projection of this pattern depends on the settings of the objective and the
additional lens. The working distance must be included between 500mm and 3000mm
for a convenient use of the product
Weight : 660g