EFT G06 User manual

EFT agriculture drone frame installation instruction
©2019 合肥翼飞特 版权所有
第1页 共 11 页

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第2页 共 11 页
Attention
This product is suitable for adults over 18 years of age.Due to the following reasons, the company will not
bear any responsibility for personal injury, property damage, etc. , please read the following terms
carefully:
1. Obtained through abnormal channels, using non-company products or imitation products.
2. Installation, setup, and use have not been performed correctly in accordance with this user manual.
3. Self-refitting and replacement of parts or accessories not produced by our company, causing damage
to the aircraft due to poor operation .
4. The user controls the aircraft while under the influence of alcohol, drugs, or physical or mental
condition.
5. Property loss and personal injury caused by the operator's subjective intentional or improper
operation.
6. This product runs poorly due to the natural aging and wear of aircraft parts.
7. Use this product in a more severe and applicable environment than marked on this product.
8. Users use this product when visibility is insufficient and their sight is blocked. 。
9. Users use this product in government air control areas, no-fly zones, etc.
10. Product damage caused by abnormal use.
AboutG06
G06 is a small plant protection drone solution specially designed for light-weight operation needs. The
effective capacity is 6 L. It uses a quick-release tank+ battery. The body is compact and foldable. It can
be equipped with radar and FPV camera. It is the first choice for entry-level plant protection drones.It
uses a three-segment fuselage layout design, a front flight control Chinese medicine box and a rear
battery. The structure is compact and the shape is unique. The flat rectangular layout plan extends the
arm to both sides and extends the nozzle spacing to the greatest extent, thereby increasing the spray
Breadth.The quick-release tank + battery design can realize quick drug and battery replacement. It is
easy to operate, saves time and effort, has a compact body, and can also be quickly folded for
convenient transportation.The whole machine adopts modular design, each component can be quickly
disassembled and replaced, which is convenient for maintenance.The optional extended rod nozzle can
effectively reduce the drift of mist droplets, and the soft silicone connection at the root can avoid the
nozzle from breaking when impacted by external forces. The optional FPV camera meets the
visualization needs of long-distance operations and makes flight more reliable.
At the same time, a fixed-height radar installation location is reserved, and millimeter-wave radar can be
selected to achieve a more accurate height-fixing imitation effect.
You can get the latest information on the EFT official website
Website：www.effort-tech.com

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第3页 共 11 页
Contents
Attention …………………………………………………2
About G06 …………………………………………………2
Installation
Unboxing
installation …………………………………………………5
Landing gear installation ………………………………………5
Arm installation …………………………………………………6
Motor set installation ……………………………………………7
Spray system installation ……………………………………………8
Appendix
Specifications …………………………………………………11

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第4页 共 11 页
Part item
Important notes
Please do not violently assemble during the assembly process, if you
are in trouble, you can call 0551-65536542
When installing the hose, do not bend it excessively, otherwise it will
cause creases and affect the spraying effect.
Be sure to connect the aircraft power supply after completing all
installation and connection.
Installation Please prepare medium-strength screw glue when installing. First complete
the unpacking inspection, and then install the landing gear, arm, motor system, and spray
system. If there are other options, install the options.
Front cover
6LQuick release tank
Frame
Back cover
Water pump and imitation radar support
Battery compartment
Extension rod nozzle (silicone )
Folding arms
Landing gear
X6 motor set

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第5页 共 11 页
Unboxing inspection
1、EFT provides users with the following documents
2、‘Product Installation Instructions’
It is recommended that users use the "Product Packing List" to check and carefully check
whether the items are missing or damaged. If there is any problem, please contact our company
in time. Read the "Product Installation Instructions" carefully, follow the instructions to complete
the installation step by step, and carefully read the relevant precautions.
Landing gear installation
图 5
图 1
图 6
1.Flip the frame
2.，Install the fixed parts mount on the landing gear
3.Align the landing gear with a fixed position on the bottom of the frame .
4.Install M3*8 screws, then turn over the frame
图 4
图 2
图 3

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第6页 共 11 页
Arms installation
Note： The installation of the arm requires the removal of some parts of the
fuselage. Please pay attention to the installation position of the removed parts
to facilitate the recovery later.
Note: When installing the arm, pay attention to the folding direction, and place
the reserved hole of the water pipe downward.
3、Remove the upper carbon plate
图 2
图 1
图 1
1、Remove the front cover
2、Remove the back cover
1、The arm passes through the arm tube clamp, and then locks after reaching the limit screw.
4、Remove the battery box
图 4
图 3
图 2

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第7页 共 11 页
Motor installation
This manual uses the Haoying X6 motor. It is recommended to install the propeller after
the aircraft performance is adjusted.
图 1
图 4
2 、Install the arm on the frame in the folding
direction as shown below,
Use the M3*10 screws that come with the body
to fix it.
3、Install the four arms on the frame.
图 4
1. Put the motor harness into the snakeskin mesh tube, weld the XT60 male , pay attention
to distinguish the positive and negative poles. (It is recommended to use a 10mm
heat-shrinkable tube to tighten the ends of the snakeskin network tube to avoid
bifurcation of the snakeskin network tube.)
2. Install the power in sequence with reference to the direction of the machine head, pass the motor
through the arm as shown in Figure 3, and insert it into the reserved power supply cord. Pay attention
to distinguish the CW/CCW motor. (Note: The battery compartment is in the direction of the tail)
图 3
图 2
图 3

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第8页 共 11 页
Spray system installation
Warning
During the installation process, please pay attention to safety. EFT will not be
responsible for any injuries and losses caused by improper operation.
图 1
图 2
图 3
图 4
1、Use M3*16 screws to fix the extension rod nozzle, place the X6 motor seat gasket under the
motor seat, and tighten the two M3*16 screws.
2、Use a 6mm water pipe to connect the extension rod nozzle, and the other end to
the built-in 6-6 pneumatic head of the frame.

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第9页 共 11 页
Appendix
Specifications
---------------------------------------------------------------------
Buck regulator
---------------------------------------------------------------------
Use method of drug breakage detection function: The drug breakage detection
factory is currently limited to the use of 25W water pump. Connect the 3pin line of the drug
breakage signal to the detection interface of the flight control liquid level meter. The drug
breakage signal is output with high and low level signals, and water is high No water is low
level, the air in the water pump needs to be exhausted before take-off to avoid
misjudgment after take-off.
Frame Specifications
Recommended configuration
Wheelbase：1172mm
Motor: HobbyWing X6/6215
Expand Size：1580*1270*475mm
Paddle: 23-24 inch folding paddle
Folded size：605*640*475mm
ESC: 60-80A FOC
Tank capacity：6L
Power supply voltage: 12S
Frame weight: 4.8kg (excluding spray system)
Maximum takeoff weight: 17.4kg
Product specification
Size: 47*34*24mm (excluding fixed ears)
Weight: 72g
Installation hole distance: 54-60mm
Power supply voltage: 15-60V
Output voltage: 12V
Maximum current: 6A
Maximum power: 72W
Stroke range: 1120-1920μs
Drug off signal: with water-high level without
water-low level

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第10 页 共 11 页
Wiring diagram
Light description
Indicator status
status
Red light flashes slowly (2
times/sec)
No input signal, need to connect the signal line
Red light flashes quickly (10
times/sec)
Input signal error, signal travel is inconsistent
Red light always on
Input signal is normal, the pump is off
Yellow light is always on
Water shortage reminder, medicine break signal
output low level
Green light always on
There is water in the water tank, and the
medicine-breaking signal outputs a high level
* If you use a brushless pump, you need to know the relevant information of the brushless pump
step-down speed governor, please contact our company in time.

EFT agriculture drone frame installation instruction
©2019 EFT All right reserved
第11 页 共 11 页
More product supports
EFT official website:：www.effort-tech.com
EFT WeChat public account：
This manual is subject to update without notice.
If you have any questions or suggestions about the manual, please contact us through the following methods.
Telephone: [phone]
Contact email: [e-mail]