EGO ST1300E User manual

LINE TRIMMER
WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
OPERATOR’S MANUAL
56 VOLT LITHIUM-ION
CORDLESS LINE TRIMMER
MODEL NUMBER ST1300E

B
D
C
E
6. Adjustable
Front-assist Handle
2. Rear Handle
1. Trigger
13. Latch
14. Battery-release
Button
7. Trimmer Head
(Bump Head)
8. Bump Knob 9. Line-cutting Blade
10. Guard
11. Ejection
Mechanism
12. Electric
Contacts
A
5. Soft Sleeve
4. Speed
Adjustment Switch
3. Lock-off Lever

H
J
I
1
2
G
K
1
2
Position 1
Position 2
ML
81
2
Front-Assist
Handle
Lower Clamp
Combination Blots
F

P
12 cm
Q
R
Tab
Notch
Eyelet
Slot
NO
11 cm

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S 5
EN
READ ALL INSTRUCTIONS!
READ & UNDERSTAND
INSTRUCTION MANUAL
Residual risk! People with electronic devices, such
as pacemakers, should consult their physician(s) before
using this product. Operation of electrical equipment
in close proximity to a heart pacemaker could cause
interference or failure of the pacemaker.
WARNING: To ensure safety and reliability, all
repairs and replacements should be performed by a
qualied service technician.
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to
possible dangers. The safety symbols and the explanations
with them deserve your careful attention and understand-
ing. The symbol warnings do not, by themselves, eliminate
any danger. The instructions and warnings they give are no
substitutes for proper accident prevention measures.
WARNING: Be sure to read and understand all safety
instructions in this Operator’s Manual, including all safety
alert symbols such as “DANGER,” “WARNING,” and
“CAUTION” before using this tool. Failure to following all
instructions listed below may result in electric shock, re,
and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARN-
ING, or CAUTION. May be used in conjunction with other
symbols or pictographs.
WARNING: The operation of any
power tools can result in foreign objects
being thrown into your eyes, which can
result in severe eye damage. Before
beginning power tool operation, always
wear safety goggles or safety glasses with
side shields and a full face shield when
needed. We recommend a Wide Vision
Safety Mask for use over eyeglasses or
standard safety glasses with side shields.
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may
appear on this product. Read, understand, and follow
all instructions on the machine before attempting to
assemble and operate.
Safety Alert Precautions that involve your
safety.
Read
Operator’s
Manual
To reduce the risk of
injury, user must read and
understand operator’s manual
before using this product.
Wear Eye
Protection
Always wear safety goggles
or safety glasses with side
shields and a full face shield
when operating this product.
Wear Ear
Protection
Always wear ear protection
when operating this product.
Ø2.0 mm Line Diam-
eter
The Diameter of the nylon
cutting line
33cm Cutting
Width
The Max. cutting width of
line trimmer
No Cutting
Blade
Do not install metal or plastic
cutting blades
IPX4
Ingress
Protection
Degree
Protection from splashing
water
Keep
Bystanders
Away
Ensure that other people and
pets remain at least 15m
away from the line trimmer
when it is in use.
15m
Keep
Bystanders
Away
Ensure that other people and
pets remain at least 15m
away from the line trimmer
when it is in use.
V Volt Voltage
A Amperes Current
Hz Hertz Frequency (cycles per
second)
WWatt Power
min Minutes Time
Alternating
Current Type of current
Direct
Current
Type or a characteristic of
current
n0
No Load
Speed Rotational speed, at no load
... /min Per Minute Revolutions per minute

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S6
EN
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using line trimmers, basic safety
precautions should always be followed to reduce the risk
of re, electric shock, and personal injury, including the
following:
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
DANGER: Do not rely on the tool’s insulation against
electric shock. To reduce the risk of electrocution, never
operate the machine in the vicinity of any wires or cables
(power, etc.) which may carry electric current.
CAUTION: Wear appropriate personal hearing
protection during use. Under some conditions and
durations of use, noise from this product may contribute
to hearing loss.
TRAINING
◾Read the instructions carefully. Be familiar with the
controls and the proper use of the machine.
◾Never allow people unfamiliar with these instructions
or children to use the machine. Local regulations can
restrict the age of the operator.
◾Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
PREPARATION
◾Never operate the machine while people, especially
children, or pets are nearby.
◾Wear eye protection and stout shoes at all times while
operating the machine.
◾The distance between the machine and bystanders
shall be at least 15m.
◾Do not use metal blades
OPERATION
◾Use the machine only in daylight or good articial light.
◾Never operate the machine with damaged guards or
shields or without guards or shields in place.
◾Switch on the motor only when the hands and feet are
away from the cutting means.
◾Always disconnect the machine from the power supply
(i.e. remove the plug from the mains or remove the
disabling device).
◾whenever leaving the machine unattended;
◾before clearing a blockage;
◾before checking, cleaning or working on the machine;
◾after striking a foreign object;
◾whenever the machine starts vibrating abnormally.
◾Take care against injury to feet and hands from the
cutting means.
◾Always ensure that the ventilation openings are kept
clear of debris.
MAINTENANCE AND STORAGE
◾Disconnect the machine from the power supply
(i.e. remove the plug from the mains or remove the
disabling device) before carrying out maintenance or
cleaning work.
◾Use only the manufacturer’s recommended
replacement parts and accessories.
◾Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾Avoid Dangerous Environments – Don’t use trimmers
in damp or wet locations.
◾Always turn the line trimmer off or remove the battery
pack whenever leaving the trimmer unattended.
◾Don’t Use In Rain.
◾Keep Children Away – All visitors should be kept at a
distance from work area.
◾Dress Properly – Do not wear loose clothing or jewelry.
They can be caught in moving parts. Use of rubber
gloves and substantial footwear is recommended
when working outdoors. Wear protective hair covering
to contain long hair.
◾Use Safety Glasses – Always use a face or dust mask if
operation is dusty.
◾Use the Right Tool– Do not use the tool for any job except
that for which it is intended.
◾Don’t Force the Trimmer – It will do the job better and
with less likelihood of a
risk of injury at the rate for which it was designed.
◾Don’t Overreach – Keep proper footing and balance at
all times.
◾Stay Alert – Watch what you are doing. Use common
sense. Do not operate the trimmer when you are tired.
◾Do not operate the trimmer while under the inuence
of alcohol or drugs.
◾Keep guards in place and in working order.
◾Store Trimmer Indoors – When not in use the trimmer

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S 7
EN
should be stored indoors in a dry and high or locked-
up place with the battery pack removed – out of
reach of children.
◾Maintain Trimmer With Care – Keep the cutting
attachment clean for best performance and to reduce
the risk of injury. Follow instructions for changing
accessories. Keep handles dry, clean, and free from oil
and grease.
◾Check Damaged Parts – Before further use of the
trimmer, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center unless indicated
elsewhere in this manual.
◾Clear the area to be cut before each use. Remove all
objects such as rocks, broken glass, nails, wire, or line
that can be thrown or become entangled in the cutting
attachment. Make sure that other persons and pets are at
least 15m away.
◾Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
◾Always hold the trimmer rmly, with both hands on the
handles while operating. Wrap your ngers and thumbs
around the handles.
◾Avoid Accidentally Starting–Don’t carry the trimmer with
your nger on the trigger.
◾Do not operate the trimmer in petrolic or explosive
atmospheres. Motors in these appliances normally
spark, and the sparks might ignite fumes.
◾Do not touch moving hazardous parts before turn off
the machine (or remove the battery pack from the
machine) and the moving hazardous parts have come
to a complete stop.
◾Damage to Trimmer – If you strike a foreign object
with the trimmer or it becomes entangled, stop the
tool immediately, remove the battery pack from the
line trimmer, check for damage and have any damage
repaired before further operation is attempted. Do not
operate with a broken guard or spool.
◾If the equipment should start to vibrate abnormally,
stop the motor , remove the battery pack from the
line trimmer. and check immediately for the cause.
Vibration is generally a warning of trouble. A loose
head may vibrate, crack, break or come off the
trimmer, which may result in serious or fatal injury.
Make sure that the cutting attachment is properly
xed in position. If the head loosens after xing it in
position, replace it immediately. Never use a trimmer
with a loose cutting attachment.
◾Replace a cracked, damaged or worn-out cutting
head immediately, even if damage is limited to
supercial cracks. Such attachments may shatter at
high speed and cause serious or fatal injury.
◾Check the cutting attachment at regular short
intervals during operation, or immediately if there is a
noticeable change in cutting behavior.
◾Only use EGOTM authorized polymer trimmer line
accessories and trimmer line that are designed for
use with this machine. Although certain unauthorized
attachments might be tted to the EGOTM line
trimmer, their use may be extremely dangerous, and/
or damaging to the tools.
◾To reduce the risk of serious injury, never use wire or
metal-reinforced line or other material in place of the
nylon cutting lines. Pieces of wire could break
off and be thrown at high speed toward the operator
or bystanders.
◾To reduce the risk of injury from loss of control, never
work on a ladder or on any other insecure support.
Never hold the cutting attachment above waist height.
◾If situations occur that are not covered in this manual,
use care and good judgment. Contact the EGO
Service Center for assistance.
◾Do not charge the battery pack in rain, or in wet
locations.
◾Use only with EGO’s battery packs and chargers.
BATTERY CHARGER
BA1120E, BA1400, BA2240E,
BA2800, BA3360, BA4200
CH5500E,
CH2100E
◾The battery pack must be removed from the appliance
before it is scrapped.
◾The battery shall be disposed of safely.
◾Do not dispose of the battery in a re. The cells may
explode. Check with local authorities for possible
special disposal instructions.
◾Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
◾Exercise care in handling batteries in order not to short
the battery with conducting materials such as rings,
bracelets, and keys. The battery or conductor may
overheat and cause burns.
◾When servicing, use only identical EGOTM replacement
parts. Use of any other accessory or attachment may
increase the risk of injury.

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S8
EN
◾Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating
condition. Be aware of possible hazards even when
the tool is not operating. Take care when performing
maintenance or service.
◾Do not wash with a hose; avoid getting water in motor
and electrical connections.
◾Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan this tool to someone else, also loan these
instructions to them to prevent misuse of the product
and possible injury.
◾Always wear substantial footwear and long trousers
while operating the machine.
◾Always be sure of the footing on slopes and to walk,
never run.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Voltage 56 V
No-load Speed 5200-6500 /min
Cutting Mechanism Bump Head
Cutting Line Type AL0802 2.0mm
Nylon twist line
Cutting Width 33 cm
Weight (without battery pack) 2.76 kg
PACKING LIST
PART NAME QUANTITY
Line Trimmer 1
Guard 1
Front-assist Handle Assembly 1
Hex Wrench 1
Screws for Locking Shaft 2
Operator’s Manual 1
DESCRIPTION
KNOW YOUR LINE TRIMMER (Fig. A)
1. Trigger
2. Rear Handle
3. Lock-off Lever
4. Speed Adjustment Switch
5. Soft Sleeve
6. Adjustable Front-assist Handle
7. Trimmer Head (Bump Head)
8. Bump Knob
9. Line-cutting Blade
10. Guard
11. Ejection Mechanism
12. Electric Contacts
13. Latch
14. Battery-release Button
ASSEMBLY
WARNING: If any parts are damaged or missing,
do not operate this product until the parts are replaced.
Use of this product with damaged or missing parts could
result in serious personal injury.
WARNING: Do not attempt to modify this product or
create accessories not recommended for use with this line
trimmer. Any such alteration or modication is misuse and
could result in a hazardous condition leading to possible
serious personal injury.
WARNING: To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the tool when assembling parts.
UNFOLDING THE SHAFT
WARNING: Do not hold the shaft at the joints in
order to avoid pinching your hands or ngers.
WARNING: Do not attempt to start the trimmer
until the shaft has been locked. Unfold the shaft gently,
ensuring the cable inside the shaft, and lock it with two
screws by the supplied wrench (Fig. B & C).
MOUNTING THE GUARD
WARNING: Always wear gloves when mounting or
replacing the guard. Take care of the blade on the guard
and protect your hand from cutting.
WARNING: Never operate the tool without the
guard rmly in place. The guard must always be on the
tool to protect the user! When the guard was xed,
never attempted to remove or adjust the guard, if
replace needed, it shall be performed by a qualied
service technician!

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S 9
EN
Loosen and remove the two combination screws from the
shaft base (Fig. D). Align the guard mounting holes with
the assembly holes and then lock the guard onto the shaft
base with the two screws. Make sure the guard is xed
according to Fig. D & E, any reverse xing will cause
great danger!
MOUNTING AND ADJUSTING THE FRONT-ASSIST
HANDLE
Attach the front-assist handle and the lower clamp onto
the shaft, pre-tightened by four combination bolts, and
then adjust the handle position to make sure your front
arm is straight, lastly tighten the bolts by the supplied
wrench (Fig. F & G).
NOTICE: The front-assist handle should be turned
upwards to point toward the top of the handle.
WARNING: Only x the front-assist handle in front of
the soft sleeve on the shaft.
WARNING: The tool can not be used without the
front-assist handle reliably xed.
OPERATION
WARNING: Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufcient to inict serious injury.
WARNING: Always wear eye protection with side
shields. along with hearing protection. Failure to do so
could result in objects being thrown into your eyes and
other possible serious injuries.
WARNING: Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING: Use your line trimmer equipped with the
appropriate cutting line only for cutting grass and similar
material.
You may use this product for the purposes listed below:
Trimming: used for removing grass and weeds up against
walls, fences, trees and borders.
Cutting: used for cutting the grass that is difcult to
reach using a normal mower.
NOTICE: The tool is to be used only for its prescribed
purpose. Any other use, for example edge trimming, is
deemed to be a case of misuse.
ATTACHING/DETACHING THE BATTERY PACK
Fully charge before rst use.
To Attach
Align the battery ribs with the mounting slots and press the
battery pack down until you hear a “click” (Fig. H).
To Detach
Depress the battery-release button and pull the battery
pack out as Fig. I shown.
HOLDING THE LINE TRIMMER
WARNING: Dress properly to reduce the risk of injury
when operating this tool. Do not wear loose clothing or
jewelry. Wear eye and ear/hearing protection. Wear heavy
duty, long trousers, boots and gloves. Do not wear short
trousers, sandals or go barefoot.
Before operating, hold the trimmer with both hands, one
hand on the rear handle and the other on the front-assist
handle which shall be straight (Fig. J). Then check for
balanced footing and a proper cutting distance without
operator bending over.
STARTING/STOPPING THE LINE TRIMMER
To Start
Press down the lock-off lever and hold it in that position.
Depress the trigger to turn on the line trimmer as Fig. K
shown.
To Stop
Release the lock-off lever and the trigger.
NOTICE: The motor has two speeds for cutting,
Position“1” for lower speed and Position “2” for high
speed, as Fig. K shown. Just push the speed adjustment
switch to the suitable position during cutting.
WARNING: Always remove the battery pack from the
line trimmer during work breaks and after nishing work.
USING THE LINE TRIMMER
WARNING: To avoid serious personal injury, wear
goggles or safety glasses at all times when operating this
unit. Wear a face mask or dust mask in dusty locations.
Clear the area to be cut before each use. Remove all ob-
jects, such as rocks, broken glass, nails, wire, or line, that
can be thrown or become entangled in the cutting attach-
ment. Clear the area of children, bystanders, and pets.
At a minimum, keep all children, bystanders and pets
at least 15m away; there still may be risk to bystanders
from thrown objects. Bystanders should be encouraged
to wear eye protection. If you are approached, stop the
motor and cutting attachment immediately.

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S10
EN
Before each use, check for damage/worn parts
Check the bump head, guard and front-assist handle
and replace the parts that are cracked, warped, bent, or
damaged in any away.
The line-cutting blade on the edge of the guard can dull
over time. It is recommended that you periodically sharp-
en it with a le or replace it with a new blade.
WARNING: Always wear gloves when mounting the
guard or sharpen or replacing the blade. Take care of the
blade on the guard and protect your hand from cutting.
After each use, clean the trimmer.
CAUTION: Obstructions in the vents will prevent
the air from owing into the motor housing and result in
overheating or damaged of the motor.
◾Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
◾Keep air vents in the motor housing from debris at
all times.
WARNING: Never use water for cleaning your
trimmer. Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from various
types of commercial solvents. Use clean cloths to remove
dirt, dust, oil, grease, etc.
ADJUSTING CUTTING LINE LENGTH
The bump head allows the operator to release more
cutting line without stopping the motor. As line becomes
frayed or worn, additional line can be released by lightly
tapping the bump knob on the ground while operating the
trimmer (Fig. L).
NOTICE: Line release will become more difcult as the
cutting line becomes shorter.
WARNING: Do not remove or alter the line cutting
blade assembly. Excessive line length will cause the motor
to overheat and may result in serious personal injury.
LINE REPLACEMENT
WARNING: Never use metal-reinforced line, wire,
rope, etc. These can break off and become dangerous
projectiles.
There are two methods to replace the cutting line:
1. Wind the spool with new line.
2. Install a pre-wound spool (AS1300, AS1301, AS1302,
if necessary, available in dealer).
Wind the spool with new line
Press the two release tabs on the spool base and pull
the spool retainer out (Fig. M). Take out approximately
7m of 2.0mm diameter cutting line. Fold and wind it onto
the spool as Fig. N & O shown. Then place the line ends
through the two opposite notches in the spool (Fig. P) and
place the spool into its retainer with notches aligned with
retainer eyelets (Fig. R). Lastly, align the retainer slots with
the tabs on the spool base and press the retainer evenly
down, ensuring that it snaps into place (Fig. Q).
NOTICE: Always clean the spool retainer, spool and spool
base before reassembling the trimmer head. Check the
spool retainer, spool and spool base for wear. If necessary,
replace the wear parts.
NOTICE: Failure to wind the line in the direction indicated
will cause the trimmer head to operate incorrectly.
Install a pre-wound spool
Press the two release tabs on the spool base and pull the
spool retainer out (Fig. M). Then place a pre-wound spool
into the retainer with notches aligned with retainer eyelets
(Fig. R). Lastly, align the retainer slots with the tabs on the
spool base and press the retainer evenly down, ensuring
that it snaps into place (Fig. Q).
NOTICE: Make sure that the tabs on the spool base snap
into place or the spool will come out during operation.
MAINTENANCE
WARNING: When servicing, use only identical
replacement parts. Inspect and maintain the machine
regularly. To ensure safety and reliability, all repairs should
be performed by a qualied service technician.
WARNING: Battery tools do not have to be plugged
into an electrical outlet; therefore, they are always in
operating condition. To prevent serious personal injury,
take extra precautions and care when performing
maintenance, service or for changing the cutting
attachment or other attachments.
WARNING: To prevent serious personal injury,
remove the battery pack from the tool before servicing,
cleaning, changing add-on attachments or removing
material from the unit.
CLEANING THE UNIT
◾Clean the unit using a damp cloth with a mild
detergent.

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S 11
EN
◾Do not use any strong detergents on the plastic
housing or the handle. They can be damaged by
certain aromatic oils, such as pine and lemon, and by
solvents such as kerosene. Moisture can also cause
a shock hazard. Wipe off any moisture with a soft dry
cloth.
◾Use a small brush or the air discharge of a small
vacuum cleaner brush to clean the air vents on the
rear housing.
STORING THE UNIT
◾Remove the battery pack from the line trimmer when
it is not in use.
◾Clean the tool thoroughly before storing it.
◾Store the unit in a dry, well-ventilated area, locked-up
or up high, out of the reach of children. Do not store
the unit on or adjacent to fertilizers, petrol, or other
chemicals.
Protecting the environment
Do not dispose of electrical appliances
as unsorted municipal waste, use
separate collection facilities.
Contact your local government for
information regarding the collection
systems available.
If electrical appliances are disposed of in
landlls or dumps, hazardous substances
can leak into the groundwater and get
into the food chain, damaging your health
and well-being.

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S12
EN
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Line trimmer fails
to start.
◾The battery pack is not attached
to the line trimmer.
◾Attach the battery pack to the line trimmer.
◾No electrical contact between
the trimmer and battery.
◾Remove battery, check contacts and reinstall the
battery pack.
◾The battery pack is depleted. ◾Charge the battery pack.
◾The lock-off lever and
trigger are not depressed
simultaneously.
◾Press down the lock-off lever and hold it, then
depress the trigger to turn on the line trimmer.
Line trimmer stops
while cutting.
◾The guard is not mounted on the
trimmer, resulting in an overly
long cutting line and motor
overload.
◾Remove the battery pack and mount the guard on
the trimmer.
◾Heavy cutting line is used. ◾Use standard nylon cutting line with diameter no
more than 2.0mm.
◾The motor shaft or trimmer head
is bound with grass.
◾Stop the trimmer, remove the battery, and remove
the grass from the motor shaft and trimmer head.
◾The motor is overloaded. ◾Remove the trimmer head from the grass. The
motor will recover to work as soon as the load is
removed. When cutting, move the trimmer head in
and out of the grass to be cut and remove no more
than 20cm of length in a single cut.
◾The battery pack or line trimmer
is too hot.
◾Allow the battery pack or trimmer to cool until the
temperature drops below 67°C.
◾The battery pack is
disconnected from the tool.
◾Re-install the battery pack.
◾The battery pack is depleted. ◾Charge the battery pack.
Trimmer head will
not advance line.
◾The motor shaft or trimmer head
is bound with grass.
◾Stop the trimmer, remove the battery, and remove
the grass from the motor shaft and trimmer head.
◾There is not enough line on the
spool.
◾Remove the battery and replace the cutting line;
follow the section “LINE REPLACEMENT” in this
manual.
◾The trimmer head is dirty. ◾Remove the battery and clean the spool, spool
retainer and spool base.
◾Line is tangled on spool. ◾Remove the battery, remove the line from the
spool and rewind; follow the section “LINE
REPLACEMENT” in this manual.
◾The line is too short. ◾Remove the battery and pull the lines while
alternately pressing down on and releasing the
bump knob.

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S 13
EN
PROBLEM CAUSE SOLUTION
Grass wraps around
trimmer head and
motor housing.
◾Cutting tall grass at ground
level.
◾Cut tall grass from the top down, removing no
more than 20cm in each pass to prevent wrapping.
Line is not cutting
well.
◾The line-cutting blade on the
edge of the guard has become
dull.
◾Sharpen the line-cutting blade with a le or
replace it with a new blade.

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E-S14
EN
WARRANTY
EGO WARRANTY POLICY
5 year warranty on EGO outdoor power equipment and 3 year warranty on EGO Power+ System battery packs and
chargers.
Please contact EGO customer service on Australia 1300 000 EGO(1300 000 346),
New Zealand 0508 000 EGO (0508 000 346) any time you have questions or warranty claims.
LIMITED SERVICE WARRANTY
FOR FIVE YEARS from the date of original retail purchase, this EGO product is warranted against defects in material or
workmanship. Defective product will receive free repair.
FOR THREE YEARS from the date of original retail purchase, the EGO Power+ System battery pack and charger are
warranted against defects in material or workmanship. Defective product will receive free repair.
This warranty does not cover routine maintenance parts and consumables that can wear out from normal use within the
warranty period.
◾This warranty applies only to the original purchaser at retail and may not be transferred.
◾The warranty period for any EGO product or part used for industrial, professional or commercial purpose is one year.
◾This warranty is void if the product has been used for rental purpose.
◾This warranty does not cover the damage resulting from modication, alteration or unauthorized repair.
◾This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect
resulting from misuse, abuse (including overloading of the product beyond capacity and exposure to water or rain),
accidents, neglect or lack of proper installation, and improper maintenance or storage.
◾This warranty does not cover normal deterioration of the exterior nish, including but not limited to scratches, dents,
paint chips, or to any corrosion or discoloring by heat, abrasive and chemical cleaners.
HOW TO OBTAIN SERVICE
For warranty service, please contact EGO customer service on Australia 1300 000 EGO(1300 000 346),
New Zealand 0508 000 EGO (0508 000 346). When requesting warranty service, you must present the original dated
sales receipt. An authorized service center will be selected to repair the product according to the stated warranty terms.
ADDITIONAL LIMITATIONS
Chervon Australia Pty Ltd ABN 36 165 077 501(“Chervon”) warrants to the original domestic purchaser that this
product will be free from defects in materials and workmanship for 5 years from date of purchase, and any battery or
charger will be free from defects in materials and workmanship for 3 years from date of purchase. To make a claim,
return the faulty item together with proof of purchase directly to your closest service agent or to the place of purchase.
Any handling and transportation costs (and other expenses incurred in claiming this warranty) are not covered by this
warranty and will not be borne by Chervon. The replacement product or part or repaired product will be made available
for your collection at an address nominated by Chervon. Where a valid warranty claim is made, Chervon will replace the
defective product or repair the fault. Where the product is repaired, Chervon may use refurbished parts. This warranty
does not cover normal wear and tear, misuse or abuse. This warranty may also be further limited or voided as speci-
cally detailed in the product Manual. Chervon has no other liability under this warranty.The benets to you given by this
warranty are in addition to other rights and remedies imposed by State and Federal legislation that cannot be excluded.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure. Chervon Australia Pty Ltd, Unit 13, 1488 Ferntree Gully Rd, Knoxeld, VIC. 3180.
Phone Number: Australia 1300 000 EGO(1300 000 346), New Zealand 0508 000 EGO (0508 000 346).
Email address: [email protected].