Eickemeyer LifeVet CP User manual

Product Information
• Product Model: LifeVet CP
• Product Name: Capnograph and Pulse Oximeter
• Manufacturer: EICKEMEYER KG
• After-service Contact Information:
Address: Eltastraße 8, 78532 Tuttlingen, Germany
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Revision History
This manual has a revision number. This revision
number changes whenever the manual is updated due to
software or technical specification change. Contents of this
manual are subject to change without prior notice.
• Revision number: V1.0
• Release time: Oct. 2016

II
Statement
Manufacturer holds the copyright of this manual, and we
are also entitled to deal with this manual as confidential files.
This manual is only used for operation, maintenance and
service of product, someone else can not publish the manual.
This manual contains exclusive information protected by
copyright laws and we reserve its copyright. Without written
approval of manufacturer no parts of this manual shall be
photocopied, xeroxed or translated into other languages.
The contents contained in this manual are subject to
amendmentswithoutnotification.
Manufacturer's Responsibility
Only under the following circumstances will
manufacturer be responsible for the safety, reliability and
performance of the instrument:
• All the installation, expansion, readjustment,
renovation or repairs are conducted by the personnel
certified bymanufacturer.
• The storage condition, operation condition and
electrical status of the instrument conforms to the product
specification.
• The instrument is used in accordance with the user’s
manual.

3
About this manual
This manual contains the instructions necessary to
operate the product safely and in accordance with its
function and intended use. Observance of this manual is a
prerequisite for proper product performance and correct
operation and ensures patient and operator safety.
This manual is based on the maximum configuration and
therefore some contents may not apply to your product. If
you have any question, please contact us.
This manual is an integral part of the product. It should
always be kept close to the equipment so that it can be
obtained conveniently when needed.
All illustrations in this manual serve as examples only.
They may not necessarily reflect the setup or data displayed
on your product.
Conventions:
• Bold Italic text is used in this manual to quote
the referenced chapter or sections.
• 【】is used to enclose screen texts.
• →is used to indicate operational procedures.

4
Signs in this manual:
Warning: Indicates a potential hazard or unsafe
practice that, if not avoided, will result in death or
serious injury.
Caution: Indicates a potential hazard or unsafe
practice that, if not avoided, could result in
minor personal injury or product/property damage.
Note: Provides application tips or other useful
information to ensure that you get the most from
your product.

Contents
Chapter 1 General Introduction .........................................1-1
Intended Use ...........................................................1-1
Main Unit ................................................................1-1
DisplayViews .........................................................1-6
Chapter 2 Safety ..................................................................2-1
SafetyInformation ..................................................2-1
Explanation of Symbols ..........................................2-5
Chapter 3 Basic Operations................................................3-1
Unpackingand Checking ........................................3-1
GettingStarted ........................................................3-1
Startingthe Monitor ................................................3-2
Screen Brightness Setting ........................................3-3
Auto-RotateSetting ................................................3-3
Date & Time Setting ...............................................3-3
Patient Information Setting ......................................3-4
Demo Mode Setting ................................................3-5
LanguageSetting ....................................................3-5
Checking the Version ..............................................3-6
Restoringthe FactoryConfiguration ........................ 3-6
Shutting off the Monitor ..........................................3-6
Chapter 4Alarm..................................................................4-1

AlarmCategories ....................................................4-1
AlarmLevels ...........................................................4-2
AlarmIndicators .....................................................4-3
Alarm Status Symbol ..............................................4-6
Alarm Tone Configuration .......................................4-6
PausingAlarms .......................................................4-7
Shutting off theAlarm Volume ................................4-8
AlarmReset ............................................................4-9
When an Alarm Occurs ...........................................4-9
Chapter 5 Measuring CO2 ..................................................5-1
Introduction ............................................................5-1
SafetyInformation ..................................................5-1
MonitoringProcedure .............................................5-2
CO2 Display ...........................................................5-6
RespiratoryRate ......................................................5-7
Setting CO2 .............................................................5-7
CO2 Zero ..............................................................5-10
Calibration ............................................................ 5-11
Removing Exhaust Gases from the System ...........5-12
Chapter 6 Measuring SpO2 ................................................6-1
Introduction ............................................................6-1
SafetyInformation ..................................................6-2

MonitoringProcedure .............................................6-4
SpO2 Display ..........................................................6-5
PR Display ..............................................................6-6
Setting SpO2 ...........................................................6-7
Setting Desat Limit .................................................6-8
Chapter 7 Trend Review .....................................................7-1
Introduction ............................................................7-1
ReviewInterface .....................................................7-1
ReviewSetup ..........................................................7-2
Chapter 8 Battery ................................................................8-1
Introduction ............................................................8-1
Charging the Battery ...............................................8-2
OptimizingBatteryPerformance ............................. 8-2
Checking the Lithium Battery .................................8-3
Disposing of the Batteries ........................................8-4
Chapter 9 Maintenance and Cleaning ................................9-1
Introduction ............................................................9-1
Seasonal SafetyChecking .......................................9-2
Cleaning theMonitor ..............................................9-4
Cleaning SpO2 Sensor ............................................9-5
Disposal ..................................................................9-5
Chapter10Accessories ..................................................... 10-1

VIII
AppendixAProduct Specifications........................................ 1
Safety Specifications.................................................... 1
Physical Specifications ................................................ 1
Environmental Specifications....................................... 2
Charging Specifications............................................... 2
Hardware Specifications.............................................. 3
Data Storage ................................................................ 4
Measurement Specifications ........................................ 5
Appendix B Factory Defaults................................................. 9
Alarm Setup................................................................. 9
System Setup................................................................ 9
CO2 Setup.................................................................. 10
SpO2 Setup................................................................ 10
Trend Setup................................................................ 10
Appendix CAlarm Message..................................................11
Physiological Alarm....................................................11
Technical Alarm......................................................... 12
Prompt Message......................................................... 14
Appendix D EMC................................................................. 15
Appendix E Warranty Registration Card........................... 16

LifeVet CP User Manual
1-1
Chapter 1 General Introduction
Intended Use
LifeVet CP patient monitor is intended for continuously
monitoring or spot checking of CO2, RR, SpO2 and PR signals
in animals.
This device can be used in institutions or units with health
care capability. For instance, outpatient departments, emergency
rooms and departments of internal medicine in hospitals, and
ordinary departments in clinics, nursing hospitals and medical
institutions for communities.
Main Unit
Front View

LifeVet CP User Manual
1-2
6 1
2
5
3
4
Fig 1-1 Front View of the Monitor
1. Alarm indicating lamp
When an alarm occurs, this lamp will light up as defined
below:
• High level alarm: the lamp quickly flashes red.
• Medium level alarm: the lamp slowly flashes yellow.
• Low level alarm: the lamp lights yellow without
flashing.
2. Displayscreen

LifeVet CP User Manual
1-3
The device uses resistive touchscreen, using stylus or
fingernail will improve sensitivity.
3. Alarm pause button
• It can pause the alarm for 120s when alarm volume is
on.
• Pressing it can change the alarm message to prompt
message when “Sensor off” alarm happens.
4. Main interface button
• Press this button to return to main interface when it is
on menu setting.
• Press this button to shift between different display
modes when it is in main interface.
5. Menu
• Press this button to enter into menu interface when it is
on main interface.
• Press this button to return to main interface when it is
on menu setting interface.
6. Battery charging indicating lamp
• It is orange when the device is being charged.
• It turns off when the battery is full or device isn’t being
charged
Rear View

LifeVet CP User Manual
1-4
Fig 1-2 Rear View of the Monitor
Side View
Topside:
1 2

LifeVet CP User Manual
1-5
Downside:
3
Rightside:
4 5
Fig 1-3 Side View of the Monitor
1. CO2 connector
2. SpO2 probe connector
3. Micro USB connector
• Connect with power adapter.
4. Shortcut key
Press this button to start or pause the CO2 measurement.
5. Power buttom
• Press it about two seconds to turn on when the monitor is
on the condition of shutdown.

LifeVet CP User Manual
1-6
• Press it about two seconds to turn off when the monitor is
on the condition of working.
• Calibration of touch screen
Press shortcut key firstly and press power button and
immediately loose shortcut key, click the center of
appearing point on screen. If the calibration passes, it will
enter the normall interface, if not, a red fork will appear
on screen and continue to calibrate.
Display Views
This device has a function of automatic display rotation
(Gravity Activated) which provides for vertical and horizontal
positioningto maximizing space utilization and visibility.

LifeVet CP User Manual
1-7
Multi-Parameter Display Mode
6 8
7
5
4
3
2
1 9
10
Fig 1-4 Multif-parameter Display Mode
1. Patient ID No.: Click and set patient information, its range
from 1 to 96.
2. SpO2 parameter area: The current SpO2 and its higher
and lower alarm limits are shown in the area.
3. SpO2 waveform area: The waveform shown in the area is
current SpO2 volume curve.

LifeVet CP User Manual
1-8
4. CO2 parameter area: The current CO2 and its higher and
lower alarm limits are shown in the area
5. CO2 waveform area: CO2 waveform is shown in the area.
6. Physiological alarm area: Current physiological alarm
information is shown in the area.
7. Technical alarm and prompt information area: Current
technical alarm and prompt information are shown in the
area.
8. Alarm status area: Alarm status symbols are shown in the
area.
9. System time: Current time is shown in the area.
10. Battery symbol: The symbol indicates the current quantity
of electricity of batteries and whether the device is
connecting power source, the alternating-current symbol
is above battery symbol when the device is connecting
power source.

LifeVet CP User Manual
1-9
SpO2 Display mode
1
2 3
Fig 1-5 SpO2 Display Mode
1. SpO2 waveform area: The waveform shown in the area is
current SpO2 volume curve.
2. SpO2 parameter area: The values shown in the area are
current SpO2 value and its higher and lower alarm limits.
3. PR parameter area: The values shown in the area are
current PR value and its upper and lower alarm limits.

LifeVet CP User Manual
1-10
CO2 Waveform Display Mode
1
2 3
Fig 1-6 CO2 Display Mode
1. CO2waveform display area: Waveform shown in the area
is current CO2 waveform 。
2. CO2 parameter area: The values shown in the area are
current HR value and its higher and lower alarm limits.
3. RR parameter area: The values shown in the area are
current RR value and its higher and lower alarm limits.

LifeVet CP User Manual
2-1
Chapter 2 Safety
Safety Information
:
Warning:
• Explosion hazard: Do not use the monitor in the
presence of flammable anesthetics mixture with air,
oxygen,or hydrogen.
• When the monitor is in use, there should not be any
great power appliances as high voltage cables, X-ray
machine, ultrasound equipment and electrizer in use
nearby.
• Do not open the monitor housings; electric shock
hazard may exist. All servicing and future upgrades
must be carried out by the personnel trained and
authorized by manufacturer only.
• When the monitor is connecting with high-frequency
devices, sensors and cables should avoid touching
high-frequency devices, in order to leakage current
burnspatient.
• Keep the monitor away from dust, vibration,
corrosive substances, explosive materials, high
temperature and moisture.