Eiki AH-35001 User manual

12
AC socket
Printed in China
TINS-B669WJZZ
04P12-CNM
INSTALLATION MANUAL
CAUTION:
••
••
•Potential hazard of glass particles if lamp ruptures. Please have an EIKI Authorized Projector Dealer or
Service Center replace lamp if rupture occurs.
••
••
•Do not remove the lamp unit directly after operation of the projector.The lamp may be extremely hot.Wait at
least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before
removing the lamp unit.
■ It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi-
cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through an EIKI Authorized Projector
Dealer or Service Center. For the name of the nearest EIKI Authorized Projector Dealer or Service Center.
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org U.S.A. ONLY
POWER button
User service screw
(for lamp unit cover)
Tab
Tab
Removing and Installing the
Lamp Unit
Info
•Ensure the lamp unit is removed using the handle.
Ensure the glass surface of the lamp unit or the
inside of the projector are not touched.
•To avoid injury to yourself and damage to the lamp,
ensure to carefully follow the steps below.
•Do not loosen other screws except for the lamp unit
cover and lamp unit.
1Press on the projector or on
the remote control to put the projec-
tor into standby mode.
•Wait until the cooling fan stops.
Warning!
•Do not remove the lamp unit from the projector
right after use. The lamp will be very hot and
may cause burn or injury.
2Disconnect the power cord.
•Unplug the power cord from the AC socket.
•Leave the lamp until it has fully cooled down
(about 1 hour).
3Remove the lamp unit cover.
•Turn the projector over. Loosen the user ser-
vice screw (1) that secures the lamp unit
cover. Pressing the tab, remove the lamp unit
cover (2).
LAMP UNIT (LAMP/CAGE MODULE) FOR PROJECTOR
Model AH-35001
4Remove the lamp unit.
•Loosen the securing screws from the lamp unit.
Hold the lamp unit by the handle and pull it in
the direction of the arrow. At this time, keep the
lamp unit horizontal and do not tilt it.
5Insert the new lamp unit.
•Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screws.
6Replace the lamp unit cover.
•Align the lamp unit cover and slide it to close.
Then tighten the user service screw to secure
the lamp unit cover.
Info
•If the lamp unit and lamp unit cover are not cor-
rectly installed, the power will not turn on, even if
the power cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
•Make sure to reset the lamp timer only when re-
placing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
1Connect the power cord.
•Plug the power cord into the AC socket of the
projector.
2Reset the lamp timer.
•While simultaneously holding down ", and
on the projector, press on the projector.
•“LAMP 0000H” is displayed, indicating that the
lamp timer is reset.
Securing screws
Handle
User service screw
(for lamp unit cover)
AC socket
POWER button
"button
ENTER button
MENU button

Für Anweisungen in Ihrer Sprache siehe Einrichtungs-Anleitung im PDF-
Format auf der mit dem Projektor mitgelieferten CD-ROM.
DEUTSCH
Pour des instructions dans votre langue, reportez-vous au guide
d’installation PDF contenu dans le CD-ROM fourni avec le projecteur.
FRANÇAIS
Para recibir instrucciones en su idioma, consulte la guía de
configuración PDF que se encuentra en el CD-ROM suministrado con
el proyector.
ESPAÑOL
日本語の説明につきましては、プロジェクター本体に付属の取扱説明書を
ご覧ください。
日本語
Per ricevere istruzioni nella propria lingua, fare riferimento alla guia di
impostazione in formato PDF incluso nel CD-ROM fornito con il
proiettore.
ITALIANO
Para instruções no seu idioma, consulte o guia de configuração em PDF
contido no CD-ROM fornecido com o projetor.
PORTUGUÊS