EINHELL RT-HA 2000 E User manual

k
tOriginal operating instructions
Hot Air Pistol
mManual de instrucciones original
Pistola de aire caliente
Bf Originalne upute za rad
Pištolj za vrući zrak
4Originalna uputstva za upotrebu
Pištolj za vrući vazduh
POryginalna instrukcja obsługi
Opalarka

Art.-Nr.: 45.201.91I.-Nr.: 11010 RT-HA 2000 E
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:56 Uhr Seite 1

GB
“CAUTION - Read the operating instructions to reduce the risk of inquiry”
7 cm
The nozzle outlet must be kept a minimum distance of 7 cm from the workpiece you are working
on or the accumulating air may cause damage to the appliance.
Arrows flash; Temperature is set
Arrows are constantly lit up; Temperature is reached.
Air flow (Settings 1-5)
Switch the hot air pistol off.
Hot air pistol is overloaded.
Overheated hot air pistol (Fault)
Error for faults which are not observed (e.g. overheated hot air pistol)
Indicators on the display
1. Key to symbols
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:57 Uhr Seite 9
2

3
1
31 2
2
54
7
6
8
313
9
11
10
12
2
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:57 Uhr Seite 2

Table of contents
1. Key to symbols
2. Safety regulations
3. Layout and items supplied
4. Intended use
5. Technical data
6. Before starting
7. Starting up
8. Replacing the power cable
9. Cleaning, maintenance and ordering of spare parts
10. Disposal and recycling
4
GB
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:57 Uhr Seite 8

Caution:
When using the appliance, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the appliance to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.
2. Safety regulations
Please refer to the booklet included in delivery for the
safety instructions!
CAUTION
Read all safety regulations and instructions. Any
errors made in following the safety regulations and
instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
Additional safety instructions
앬Ensure that the ON/OFF switch is set to “0” (OFF)
before you insert the plug into the socket.
앬The nozzle can reach temperatures of up to
630°. Caution Risk of burns! Wear gloves and
protective goggles. During operation the
nozzle should not be touched.
앬Let the hot air pistol cool off completely before
clearing up.
앬Never leave the appliance in the rain or in damp
places. Store the appliance in a dry place.
앬Never leave the appliance unsupervised. Keep
the appliance away from children.
앬Never aim the air flow at people or animals.
The appliance may not be used to dry clothes
or hair. The hot air blower may not be used as
a hair dryer.
앬The appliance must not be used near highly
inflammable or explosive substances and gases.
앬Never restrict the hot air flow by blocking or
covering the air outlet.
앬Only use original accessories and spare parts
from the manufacturer.
앬Never wear loose clothing or jewellery. Wear non-
slip shoes and a hairnet if you have long hair.
Ensure that you maintain a steady foothold.
앬Never use the appliance in a wet environment or
in areas where relative humidity is high
(bathroom, sauna, etc.)
앬Check your working area for highly inflammable
substances before using the hot air pistol.
앬Never carry the hot air pistol by its Power cable.
앬Only use extension cables with a minimum cross-
section of 1.5mm2
앬Repairs (e.g. exchange of power cable) may only
be carried out by a qualified electrician.
앬Do not use chemical removers and solvents at
the same time as the hot air pistol.
앬Clean the nozzle if it gets dirty.
앬Make sure the openings for the air inlet and outlet
are always clean and free of dirt.
앬When removing colour or working with plastics,
vapours which could be damaging to
health/poisonous may be produced. Make sure of
adequate air supply when working in a house.
앬Never aim the hot air directly at a window or other
glass surfaces.
앬This appliance is not designed to be used by
people (including children) with limited physical,
sensory or mental capacities or those with no
experience and /or knowledge unless they are
supervised by a person who is responsible for
their safety or they have received instructions
from such a person in how to use the appliance
safely. Children must always be supervised in
order to ensure that they do not play with the
appliance.
앬Fires can be caused if the appliance is not
handled carefully and correctly.
앬Take care when using the appliance near
inflammable substances. Do not aim the pistol at
the same point for a long time.
앬Do not use in explosive atmospheres.
앬Warmth may be carried to inflammable materials
which are concealed.
앬After use, let the appliance cool on the stand
before it is put away.
앬Do not leave the appliance unsupervised when it
is in operation.
3. Layout and items supplied (Fig. 1/2)
1. Nozzle
2. 4-setting ON/OFF switch
3. Handle
4. Heat nozzle
5. Wide nozzle
6. Reducer nozzle
7. Reflector nozzle
8. Paint scraper
9. Temperature -
10. Temperature +
11. Air flow -
5
GB
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:57 Uhr Seite 10

12. Air flow +
13. Display
4. Intended use
The hot air blower is designed for heating shrink-fit
hoses, for removing paint and for welding and
shaping plastics.
The appliance is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user/operator - not the manufacturer -
will be liable for any damage or injuries caused as a
result thereof.
Please note that our appliance has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
appliance is used in commercial, trade or industrial
businesses or for equivalent purposes.
5. Technical data
Mains voltage: 230 V ~ 50 Hz
Power input: max. 2000 W
Temperature: 50°C / Setting I
50 - 630°C / Setting II
50 - 630°C / Setting III
Air volume: 120 l/min-1 / Setting 1
240 l/min-1 / Setting 2
360 l/min-1 / Setting 3
480 l/min-1 / Setting 4
550 l/min-1 / Setting 5
Protection class: II/쏾
Weight: 0.9 kg
6. Before starting the appliance
Before you connect the appliance to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
7. Starting up
7.1 4-setting ON/OFF switch (Fig. 3)
Select the required operating temperature and air
volume with the ON/OFF switch (2).
Within a very short space of time the hot air
pistol will reach operating temperature.
Switch position I:
I. Setting 50°C / 120 - 550 l/min-1
Switch position II:
II. Setting 50 - 630°C / 120 - 550 l/min-1
Switch position III:
III. Setting 50 - 630°C / 550 l/min-1
7.1.1 Indicators on the display:
If the temperature is adjusted to Setting II or III
(Temperature adjustment is possible at intervals
of 10°C) the arrows flash until the set
temperature is reached. After this the arrows are
constantly lit up.
If the symbol (switch off hot air pistol) appears on
the display, the appliance should first be stopped
before using again.
If the hot air pistol is overloaded at Setting II or
III, the temperature can be changed from above,
however the hot air pistol carries on running at
constant temperature.
7.2 Possible uses of the hot air pistol:
Removal of colour and paint.
Important: When removing colours and
paints, vapours which could be damaging to
health/poisonous may be produced. Make
sure of adequate ventilation.
Removal of labels and decoration.
Loosening of rusty or over-tightened nuts and
metal screws.
Thawing frozen pipes, door locks, etc. Do not
thaw plastic or synthetic pipes.
Removal of natural grains on wood surfaces
before staining or painting.
Shrinking of PVC packaging and insulating
hoses.
Waxing of skis.
Important: Intense exposure to heat raises the
risk of fire and explosion!
Make sure the workplace is well-aired. The
remaining gases and vapours could be damaging
to health/or poisonous.
GB
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:57 Uhr Seite 11
6

7.3 Selecting the right nozzle
Heat nozzle (4) protects materials (e.g. glass
panes) from the hot air by redirection. For
removing paint.
The wide nozzle (5) provides uniform air
distribution on small surfaces.
The reducer nozzle (6) provides a targeted jet of
heat for corners and for soldering work.
The reflector nozzle (7) is designed for soldering
and shaping tubes, for defrosting water pipes
and for shrinking insulating hoses.
8. Replacing the power cable
If the power cable for this appliance is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the appliance with a clean cloth or blast it
with compressed air at low pressure.
We recommend cleaning the appliance
immediately after every use.
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the
plastic parts in the appliance. Ensure that no
water can get into the interior of the appliance.
9.2 Maintenance
There are no parts inside the appliance which require
additional maintenance.
9.3 Ordering replacement parts:
Please provide the following information on all orders
for spare parts;
Model/type of the appliance
Article number of the appliance
ID number of the appliance
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
10. Disposal and recycling
The appliance is supplied in packaging to prevent it
from being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system. The appliance
and its accessories are made of various types of
material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.
7
GB
Anleitung_RT_HA_2000_E_SPK7:_ 01.03.2010 16:57 Uhr Seite 12

GUARANTEE CERTIFICATE
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely
event that your device develops a fault, please contact our service department at the address shown on this
guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under
the service number printed below. Please note the following terms under which guarantee claims can be made:
1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.
We do not charge you for this guarantee.
2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the
rectification of these defects or replacement of the device. Please note that our devices have not been
designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated
if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The
following are also excluded from our guarantee: compensation for transport damage, damage caused by
failure to comply with the installation/assembly instructions or damage caused by unprofessional
installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or
current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools
or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies
into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by
the device being dropped) and normal wear resulting from proper operation of the device.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee
claims should be submitted before the end of the guarantee period within two weeks of the defect being
noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee
period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts fitted will not result in an extension of the guarantee period, and no new
guarantee will become active for the work performed or parts fitted. This also applies when an on-site
service is used.
4. In order to assert your guarantee claim, please send your defective device postage-free to the address
shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of
purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if
you could describe the nature of the problem in as much detail as possible. If the defect is covered by our
guarantee then your device will either be repaired immediately and returned to you, or we will send you a
new device.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the
scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send
the device to our service address.
EINHELL AUSTRALIA PTY LTD
6/166 Wellington Street
Collingwood VIC 3066
Australia
Phone: [phone]
8