Eizo ColorEdge CG277 User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Cover

2
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are
subject to change without notice.

3
Noticeforthismonitor
Notice for this monitor
Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to
applications such as creations of images and graphics, and digital photo processing, where accurate color reproduction
is a priority.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please
wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.

4Noticeforthismonitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
If necessary, the stains on the cabinet and panel surface can be removed by using the provided ScreenCleaner.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Cover ...................................................................... 1
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 7
1-1. Features ......................................................... 7
1-2. Controls and Functions ............................... 9
●Front................................................................ 9
●Rear................................................................10
1-3. EIZO LCD Utility Disk...................................11
●Diskcontentsandsoftwareoverview............11
●TouseColorNavigator...................................11
1-4. Basic Operations and Functions ...............12
●BasicAdjustmentmenuoperations...............12
●ShowingButtonGuide...................................13
●Functions........................................................13
Chapter 2 Adjusting Screens .......................... 15
2-1. Setting Resolution .......................................15
●CompatibleResolutions/Formats...................15
●Toswitchsignalformats.................................16
●Todisplay4KsignalsbyDisplayPort
signalinput.....................................................16
●TosetthedisplayresolutionfortheOS.........17
●Toselectscreensize......................................18
2-2. Selecting the display mode (color mode) 20
2-3. Adjusting Color ............................................21
●Toadjustbrightness.......................................21
●Toadjustthetemperature............................. 22
●Toadjustgamma........................................... 22
●Tosetcolorgamut......................................... 23
●Toperformadvancedadjustments............... 23
2-4. Conguring Moving Image Performance . 27
2-5. Specifying Color Space ............................. 28
2-6. Expanding Signal Output Range .............. 28
●Toextendtheoutputrange........................... 28
●Toselecttherangeofsignalstoextend....... 29
2-7. Setting HDMI ................................................ 29
●Toreducenoise............................................. 29
●Toselecthowtodisplayinterlacesignal....... 29
●Tosettingsafearea....................................... 30
Chapter 3 Setting Monitor ............................... 31
3-1. Setting Adjustment Menu ...........................31
●SelectingtheLanguage.................................31
●SettingOrientation.........................................31
●Tochangeadjustmentmenudisplayposition31
3-2. Skipping Unused Display Modes .............. 32
3-3. Showing and Hiding the EIZO Logo ......... 32
3-4. Locking Operation Buttons ....................... 32
3-5. Changing DUE (Digital Uniformity
Equalizer) Setting ....................................... 33
3-6. Reset to default ........................................... 34
●Toresetthecoloradjustments...................... 34
●Toresetalladjustmentstothedefault
settings.......................................................... 34
Chapter 4 SelfCalibration ................................ 35
4-1. Setting the Color Mode for Executing
SelfCalibration ............................................ 35
●CALmode..................................................... 35
●StandardMode.............................................. 35
4-2. Setting Monitor Date and Time.................. 36
4-3. Setting Calibration Schedule .................... 36
4-4. Setting the calibration targets .................. 38
4-5. Executing SelfCalibration .......................... 39
4-6. Checking Adjustment Results ................... 40
●TocheckadjustmentresultswithCALmode40
●Tocheckadjustmentresultswith
StandardMode.............................................. 40
Chapter 5 Connecting Multiple External
Devices ............................................ 41
5-1. To switch among input signals ................. 42
5-2. To set input signal selection...................... 42
5-3. Skipping Unused Input Signals ................. 42
5-4. Switching USB Port Automatically ........... 43
Chapter 6 Power Saving Functions ................44
6-1. Setting Power Save ..................................... 44
6-2. Sets the brightness of the indicator ......... 45
6-3. Setting DisplayPort Power Save ............... 45
Chapter 7 Troubleshooting ..............................46
7-1. No picture .................................................... 46
7-2. Imaging problems ........................................47
7-3. Other problems ........................................... 48
7-4. Built-in calibration sensor and
SelfCalibration problems ........................... 49
Chapter 8 Reference ........................................50
8-1. Attaching the Optional Arm ....................... 50
8-2. Making Use of USB (Universal Serial
Bus) ................................................................51
●SystemRequirement......................................51
●Procedure.......................................................51
8-3. Showing Monitor Information.................... 52

6CONTENTS
●Displayingsignalinformation.........................52
●DisplayingMonitorInformation......................52
8-4. Specications ............................................. 53
Chapter 9 Glossary .......................................... 56
Appendix .............................................................. 59
Trademark ............................................................... 59
License / Copyright ................................................ 59
FCC Declaration of Conformity ............................ 60
Hinweise zur Auswahl des richtigen
Schwenkarms für Ihren Monitor ............................61
Hinweis zur Ergonomie : ........................................61
LIMITED WARRANTY ............................................. 62
Recycling Information ............................................71
China Measures for RoHS Compliance in
ChinaRoHS ...............................................................75

7
Chapter1Introduction
Chapter 1 Introduction
1-1. Features
• 27.0″ wide format LCD
• Wide color gamut (Adobe RGB coverage: 99%)
• Supports a resolution of 2560 × 1440.
• IPS panel with 178˚ horizontal and vertical viewing angles
• Frame synchronization mode supported (23.75 - 30.5Hz, 47.5 - 61.0Hz)
• 3 signal input terminals (DVI-D × 1, HDMI × 1, DisplayPort × 1)
- DisplayPort (applicable to 8 bit and 10 bit)*1
Supports reduced display of 4K signals
- HDMI (applicable to 8 bit, 10 bit, and 12 bit)*1, *2
Can handle PC signals in HDMI input
*1 Not applicable to audio signals.
*2 The maximum screen display is 10 bits.
• Color mode function
Reproduces a color temperature, gamma, and gamut compliant with the following standard.
- Broadcasting standards “EBU/REC709/SMPTE-C”
- Digital cinema standard “DCI”
- Adobe® RGB / sRGB
See “2-2. Selecting the display mode (color mode)” (page 20)
• Attaching the “Adjustment Certicate”, which describes the factory measurement results of the grayscale and
uniformity characteristics for each monitor
• Portrait/Landscape display available (rotate 90˚ clockwise)
• This product is equipped with a built-in calibration sensor, and supports SelfCalibration in which the monitor
executes calibration independently.
See “Chapter 4 SelfCalibration” (page 35)
• The provided Color Management Software “ColorNavigator” enables you to calibrate monitor characteristics
and generate color proles
See “1-3. EIZO LCD Utility Disk” (page 11)
• Power saving function
Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving
function.
- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
• Displays HDCP (High-bandwidth Digital Protection) protected contents.

8Chapter1Introduction
Attention
Be careful of the following points when using the built-in calibration sensor.
Do not touch the built-in calibration sensor.
Itmayreducethemeasurementaccuracyofthebuilt-incalibrationsensor,orresultininjury
orequipmentdamage.
Attention
• A high temperature or high humidity environment may affect the measurement accuracy of the built-in calibration
sensor. We suggest storing and using the monitor under the following conditions.
- Temperature 30ºC or less
- Humidity 70% or less
Avoid storing or using the sensor where it may be exposed to direct sunlight.
Note
• This monitor supports both portrait and landscape format. You can change the orientation of the Setting menu when
using the monitor screen in vertical display position. (See “Setting Orientation” (page 31))
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details.

9
Chapter1Introduction
1-2. Controls and Functions
●Front
1
7 8 92 4 5 3
6
Adjustmentmenu*1
1. Built-in calibration sensor Executescalibrationforanindependentmonitor.SelfCalibrationfunction(page35)
2. Ambient Light Sensor Measuresambientlight.
3. button Switchesinputsignalsfordisplay(page42).
4. button ChangesColorMode(page20).
5. button Cancelsthesetting/adjustmentandexitstheAdjustmentmenu.
6. buttons • Providesthemenuselectionaswellastheadjustmentandsettingofafunction.
• DisplaystheBrightnessmenu(page21).
7. button DisplaystheAdjustmentmenu,determinesanitemonthemenuscreen,andsaves
valuesadjusted(page12).
8. button Turnsthepoweronoroff.
9. Power Indicator
Indicatesthemonitor’soperationstatus.
Blue: Operating
Flashingblue(2timesforeach): Indicatesthatrecalibrationisrequiredifthe
SelfCalibrationschedule(page36)isset.
Orange: Powersavingmode
OFF: Mainpower/Poweroff
*1 See “1-4. Basic Operations and Functions” (page 12) for how to use.

10 Chapter1Introduction
●Rear
16
17
15
10 11 12 1314
10. Main power switch Turnsthemainpoweronoroff.
11. Power connector Connectsthepowercord.
12. Input signal connectors Left:DVI-Dconnector/Center:HDMIconnector/Right:DisplayPortconnector
13. USB upstream port ConnectstheUSBcabletousethesoftwarethatneedsUSBconnection,ortouse
USBhubfunction(page51).
14. USB downstream port ConnectsaperipheralUSBdevice.
15. Stand*2 Usedtoadjusttheheightandangleofthemonitorscreen.
16. Security lock slot ComplieswithKensington’sMicroSaversecuritysystem.
17. Cable holder Coversthemonitorcables.
*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “8-1. Attaching the Optional Arm”
(page 50)).

11
Chapter1Introduction
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents
and the overview of the software programs.
●Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.txt” or
the “read me” le on the disk for software startup procedures or le access procedures.
Contents Overview Windows Macintosh
A“Readme.txt”or“readme”le √ √
ColorNavigator Anapplicationsoftwareforcalibratingmonitorcharacteristics
andgeneratingICCproles(forWindows)andApple
ColorSyncproles(forMacintosh).
(APCmustbeconnectedtothemonitorwiththesuppliedUSB
cable.)
√ √
User’sManualofthismonitor(PDFle) √ √
●To use ColorNavigator
Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For
details of the USB cable connection, see “8-2. Making Use of USB (Universal Serial Bus)” (page 51).

12 Chapter1Introduction
1-4. Basic Operations and Functions
●Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press . The Adjustment menu appears.
Currentmode
Menutitle
Setting
Menu
Item
2.
Adjusting/Setting
1. Choose a menu to adjust/set with , and then press .
2. Choose an item to adjust/set with , and then press .
3. Adjust/set the selected item with , and then press .
3.
Exiting
1. Press a few times. The Adjustment menu nishes.

13
Chapter1Introduction
●Showing Button Guide
When you press the front buttons (except the button), the button guide appears next to the button.
Note
• The button guide will continue to appear while the Adjustment menu or Mode menu is showing.
• The contents of the button guide will differ depending on the selected menu or status.
• In CAL mode, the brightness cannot be adjusted even though the button guide is displayed above the and buttons.
●Functions
The following table shows the menus for adjustment and setting items of each menu.
Main Menu Item Reference
Color
(StandardMode)*1 Brightness “2-3.AdjustingColor”(page21)
Temperature
Gamma
ColorGamut
Advanced
Settings Hue
Saturation
Cliping
Gain
BlackLevel
6Colors
ColorReset “3-6.Resettodefault”(page34)
Color
(CALMode)*2 Target SelfCalibration “4-1.SettingtheColorModeforExecuting
SelfCalibration”(page35)
Brightness “4-4.Settingthecalibrationtargets”(page38)
WhitePoint
ColorGamut
GamutSettings
Gamma
Result CalibrationResult “4-6.CheckingAdjustmentResults”(page40)
AmbientLight
ColorReset “3-6.Resettodefault”(page34)

14 Chapter1Introduction
SelfCalibration Execute “4-5.ExecutingSelfCalibration”(page39)
StandardMode SelfCalibration “4-1.SettingtheColorModeforExecuting
SelfCalibration”(page35)
Result “4-6.CheckingAdjustmentResults”(page40)
Settings Schedule “4-3.SettingCalibrationSchedule”(page36)
Clock
Adjustment
“4-2.SettingMonitorDateandTime”(page36)
Screen ScreenSize “Toselectscreensize”(page18)
Overdrive “2-4.ConguringMovingImagePerformance”
(page27)
ColorSpace “2-5.SpecifyingColorSpace”(page28)
Range
Extension RangeExtension “2-6.ExpandingSignalOutputRange”(page28)
SuperWhite
HDMI
Settings*3 NoiseReduction “2-7.SettingHDMI”(page29)
Filmdetection
SafeAreaMarker
SafeAreaSize
BoderColor
Power
Manager PowerSave “6-1.SettingPowerSave”(page44)
Indicator “6-2.Setsthebrightnessoftheindicator”(page
45)
MenuSettings Language “SelectingtheLanguage”(page31)
Orientation “SettingOrientation”(page31)
MenuPosition “Tochangeadjustmentmenudisplayposition”
(page31)
Tools InputSelection “5-2.Tosetinputsignalselection”(page42)
InputSkip “5-3.SkippingUnusedInputSignals”(page42)
ModeSkip “3-2.SkippingUnusedDisplayModes”(page32)
USBSelection “5-4.SwitchingUSBPortAutomatically”(page
43)
SignalInfo “8-3.ShowingMonitorInformation”(page52)
Monitorinfo
AllReset “3-6.Resettodefault”(page34)
*1 Functions available for adjustment and setting in Standard Mode (page 20) are displayed.
*2 Functions available for adjustment and setting in CAL Mode are displayed.
*3 This function is available with HDMI signal input.

15
Chapter2AdjustingScreens
Chapter 2 Adjusting Screens
2-1. Setting Resolution
●Compatible Resolutions/Formats
The monitor supports the following resolutions and signal format
Digital Input (DVI-D, DisplayPort, HDMI: PC signal)
Resolution Vertical scan
frequency
DVI-D
(Single Link)
DVI-D
(Dual Link) DisplayPort HDMI*1
640x480 60Hz √ √ √ √
720x400 70Hz √ √ √ √
800x600 60Hz √ √ √ √
1024x768 60Hz √ √ √ √
1280x960 60Hz √ √ √ √
1280x1024 60Hz √ √ √ √
1600×1200 60Hz √ √ √ √
1920×1080 60Hz √ √ √ √
1920×1200 60Hz √ √ √ √
2560×1440 30Hz √*2 - - √
2560×1440*3 60Hz - √ √ -
3840×2160 24Hz/25Hz/30Hz - - √*4 -
4096×2160 24Hz/25Hz/30Hz - - √*4 -
Digital Input (HDMI: video signal*1)
Format Vertical scan frequency
24Hz 25Hz 30Hz 50Hz 60Hz
640x480 - - - - √
480i - - - - √
480p - - - - √
576i - - - √ -
576p - - - √ -
720p - - - √ √
1080i - - - √ √
1080p √ √ √ √ √
*1 When displaying PC signals by HDMI signal input, change the monitor’s setting in advance (see (“To switch signal
formats” (page 16)).
*2 When displaying in this resolution or vertical scan frequency, change the monitor’s setting in advance (see “To
switch signal formats” (page 16)).
*3 Recommended resolution
*4 See “To display 4K signals by DisplayPort signal input” (page 16)

16 Chapter2AdjustingScreens
●To switch signal formats
The monitor’s displayable resolution can be changed. Use this function in the following cases.
• DVI: When displaying a dedicated resolution and vertical scan frequency for Single Link
• HDMI: When displaying PC signals
Adjustable Range
• DVI: Dual Link / Single Link
• HDMI : Video / PC
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Signal Selection” from “Optional Settings”, and press .
4. Choose the input signal to set with or , and press .
5. Select “Signal Format” with the selected input signal and press .
6. Switch the signal format with or .
7. Select “Finish” with or .
8. Press .
●To display 4K signals by DisplayPort signal input
When using DisplayPort signal input, 4K signals (resolutions of 3840 × 2160 and 4096 × 2160) can be reduced
and displayed on full screen.
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Signal Selection” from “Optional Settings”, and press .
4. Select “DisplayPort” from “Optional Settings”, and press .
5. Select “Signal Bandwidth”, and press .
6. Switch the setting with or .
Select “4K” to enable display of 4K signals.
7. Select “Finish” with or .
8. Press .
Note
• When displaying 4096 × 2160 resolution signals, blank borders may appear at the top and bottom of the screen to
maintain the aspect ratio.

17
Chapter2AdjustingScreens
●To set the display resolution for the OS
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change
the resolution, follow the procedure below.
Windows 8 / Windows 7
1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a conrmation dialog box is displayed, click “Keep changes”.
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution
for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close the
window.

18 Chapter2AdjustingScreens
●To select screen size
The image with the resolution other than the recommended resolution is displayed in full screen automatically.
You can change the screen size by using the “Screen Size” function from “Screen”.
DVI, DisplayPort, HDMI (PC signal) input
Settings Function
Full Displaysanimageinfullscreen.Imagesaredistortedinsomecasesbecausethevertical
rateisnotequaltothehorizontalrate.
Enlarged Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder
appearstoequalizetheverticalrateandthehorizontalrate.
Normal Displaysimageswiththespeciedresolution.
Example: Image size 1280 × 1024
Full Enlarged Normal
2560×1440 1800×1440 1280×1024
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Full”, “Enlarged”, or “Normal” with or .
4. Press to exit.
HDMI (HD signal) input
Settings Function
Enlarged Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder
appearstoequalizetheverticalrateandthehorizontalrate.
DotbyDot Displaysimageswiththespeciedresolution.
Example: 720p
Enlarged DotbyDot
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Enlarged”, or “Dot by Dot” with or .
4. Press to exit.

19
Chapter2AdjustingScreens
HDMI (SD signal) input
Settings Function
Auto Themonitorautomaticallychangesthescreensizeaccordingtotheaspectratiosentfrom
theautoinputsignal.
4:3 Displaysimagesina4:3formatscreen.Blackbarsappearonbothsidesofthescreen.
16:9imagesarehorizontallycompressed.
LetterBox Displays16:9letterboxedimagesinfullscreen.
Imagesotherthantheletterboxedonesarepartlycutontopandbottom.
16:9 Displaystheentire16:9imageinfullscreen.Blackbarsappearonthetopandbottomof
thescreen.4:3imagesarehorizontallyexpanded.
Example: 480i/480p (16:9)
Auto 4:3 LetterBox 16:9
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Auto”, “4:3”, “Letter Box”, or “16:9” with or .
4. Press to exit.

20 Chapter2AdjustingScreens
2-2. Selecting the display mode (color mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
StandardMode Adjustcolorusingthemonitor’sAdjustmentmenu.
1-Custom Availableforthecolorsettingsaccordingtoyourpreference.
2-Adobe®RGB SuitableforcolormatchingwithAdobe®RGBcompatibleperipherals.
3-sRGB SuitableforcolormatchingwithsRGBcompatibleperipherals.
4-EBU SuitableforreproducingthecolorgamutandgammaassetforthbyEBU(European
BroadcastingUnion)standards.
5-REC709 SuitableforreproducingthecolorgamutandgammaassetforthbytheITU-RRec.709
standard.
6-SMPTE-C SuitableforreproducingthecolorgamutandgammaassetforthbySMPTE-Cstandards.
7-DCI SuitableforreproducingthecolorgamutandgammaassetforthbyDCIstandards.
CALMode Adjustthemonitor’scolorusingsoftware.
8-CAL1
9-CAL2
10-CAL3
DisplaysthescreenadjustedbytheColorManagementSoftware“ColorNavigator”and
SelfCalibration.
Attention
• Avoid operating any funciton of the monitor while using ColorNavigator.
Example:
Themodemenu
appears.
1-Custom←→2-Adobe®RGB←→3-sRGB←→4-EBU←→5-REC709
10-CAL3←→9-CAL2←→8-CAL1←→7-DCI←→6-SMPTE-C
Procedure
1. Press .
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the mode with or while the mode menu is displayed.
Note
• The Adjustment menu and the Mode menu cannot be displayed at the same time.
• You can disable a specic mode to be selected. For more information, see “3-2. Skipping Unused Display Modes” (page 32).