Ekofires 8010 Assembly Instructions

INSTA ATION & USER INSTRUCTIONS
All instructions must be handed to the user
for safekeeping.
WA INSET GAS FIRES
Revision A - 05/17
© 2017 Focal Point Fires plc
GB IE
1
Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not per-
mitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.
IN THE UK A WAYS USE A GAS SAFE REGISTERED ENGINEER TO INSTA , REPAIR OR SERVICE THIS APP IANCE
MO EL SHOWN : EKO 8010 WALL INSET GAS FIRE
MODE S COVERED BY THESE INSTRUCTIONS
8010 WA INSET GAS FIRE
8020 WIDE WA INSET GAS FIRE
AVAI AB E IN S IDE CONTRO & REMOTE CONTRO
Christchurch, Dorset BH23 2BT
Tel: [phone]
Fax: [phone]
www.ekofires.co.uk
e-mail: [e-mail]

• This appliance is an Inset ecorative Fuel Effect appliance which provides radiant warmth utilising the latest type burner technology.
• The fire is designed to suit various types of fireplaces and natural draught flues as detailed in this manual.
• The appliance must be installed by a competent person in accordance with Gas Safety (Installation and Use) Regulations 1998. It is
strongly recommended that a GAS SAFE registered engineer be used for this purpose.
• Read all these instructions before commencing installation.
• This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space.
• This appliance is factory set for operation on the gas type, and at the pressure stated on the appliance data plate.
• In the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve.
• The appliance must be installed in accordance with the following:
• Failure to comply with the above could lead to prosecution and deem the manufacturer’s warranty invalid.
• The appliance is designed to fit various types of situations as described in sections 3.0 and 4.0.
• It should be noted that heaters create warm air currents. These currents move heat to wall surfaces next to the heater. Installing the
heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air (such as tobacco smoke, candle smoke
etc.) exist, may cause the walls to become discoloured.
• WARNING: The manufacturer of this appliance considers all surfaces as working surfaces with the exception of the control knob
• As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children, and the elder-
ly or infirm.
• Consult ALL instructions before installation and use of this appliance.
• This appliance is free from any asbestos material.
• Refractories and fuel bed are constructed from ceramic fibre.
• Slide control models : These appliances feature a battery-operated control system, and under normal usage will need a new battery
approximately every twelve months.
Burner/spark generator requirements - 1 x AA (1.5 volt)
Refer to the appropriate section of these instructions for details of how to change the battery.
• Remote control models : This appliance features a battery-operated remote control system, and under normal usage will need
new batteries approximately every twelve months.
Remote control Handset requirements - 1 x ‘PP3’ type (9 volt)
Receiver/motor unit requirements - 4 x ‘AA’ type (1.5 volt)
Refer to the appropriate section of these instructions for details of how to change the batteries.
I N S T A A T I O N I N S T R U C T I O N S
2
GB IE
•Manufacturers' Instructions.
•The Building Regulations issued by the epartment for Communities and Local Government, the Building Standards (Scotland)
(Consolidation) Regulations issued by the Scottish evelopment epartment.
•Relevant British Standards insofar as the relevant areas are not covered by these instructions.
•For Republic of Ireland, reference should be made to the current edition of IS813 (the relevant standards governing installation).
Section
1.0
2.0
3.0
4.0
4.1
5.0
6.0
6.1
7.0
7.1
7.2
7.3
7.4
7.5
7.6
8.0
8.1
8.2
Content
Important Notes
Appliance ata
Installation Requirements
Site Requirements
ebris Collection Space
Ventilation
Unpacking the Appliance
Component Checklist
Preparing the Appliance
Preparing the Opening
Gas Supply Routing
Installing the Firebox
Installing the Ceramic Tiles
Installing the Burner
Gas Connection
Testing and Commissioning
Spark Gap
Installing the Ceramics
Page No.
2
3
3
3
4
5
5
5
5
6
6
7
7
8
8
8
8
8
Section
8.3
8.4
8.5
8.6
8.7
8.8
8.9
9.0
10.0
10.1
10.2
10.3
10.4
10.5
10.6
10.7
11.0
11.1
Content
Assembling the Appliance
Operating the Appliance
Operating Pressure - Manual, Slide & Remote Controls
Flue Spillage Monitoring System
Testing for Spillage
Final Assembly
Fitting the ecorative Frame Assembly
Briefing the Customer
Servicing
Cleaning the Ceramics
Removing the Burner
Servicing the Burner
Pilot Assembly
Removing the Firebox
Replacing the Batteries- Remote Controls
Replacing the Batteries- Slide Controls
Troubleshooting Guide
Troubleshooting Guide- Remote Controls
Page No.
8
9
9
9
9
10
10
10
11
11
11
11
11
12
12
12
12
13
1.0 IMPORTANT NOTES
© 2017 Focal Point Fires plc.

These appliances have been tested for use with circular flues of a minimum internal diameter of 125mm. The fireplace opening should
be inspected and repairs made where necessary.
All models : This appliance requires a natural draught flue system which may be one of the following;
125mm (5in) minimum diameter flexible flue liner.
125mm (5in) minimum diameter twin wall flue conforming to BS 715.
2.0 APP IANCE DATA
3
GB IE
4.0 SITE REQUIREMENTS
Please see ata Badge affixed to appliance for current data. This appliance is for use only with the gas type, and at the pressure stated
on the appliance ata Badge, and is for decorative purposes.
© 2017 Focal Point Fires plc.
Specifications Wall inset slide control
models
Wall inset remote
control models
Wide wall inset slide
control models
Wide wall inset remote
control models
Efficiency 70% (net), 63% (gross) 70% (net), 63% (gross) 70% (net), 63% (gross) 70% (net), 63% (gross)
Main burner injector Stereo size 1.47 Stereo size 1.44 Stereo size 1.53 Stereo size 1.50
Oxypilot Copreci 21100 2F/297 Copreci 21100 2F/297 Copreci 21100 2F/297 Copreci 21100 2F/297
Gas Control Teddington TESA 3173/011 Mertik Maxitrol GV60 series Teddington TESA 3173/011 Mertik Maxitrol GV60 series
Gas Inlet All models - 8mm compression - Inlet restrictor elbow
Ignition Battery Spark Battery Spark Battery Spark Battery Spark
Spark Gap 3.5 - 4.5mm 3.5 - 4.5mm 3.5 - 4.5mm 3.5 - 4.5mm
Flue specification 125mm (5in) minimum diameter flexible flue liner.
125mm (5in) minimum diameter twin wall flue conforming to BS 715.
3.0 INSTA ATION REQUIREMENTS
This appliance MUST NOT be installed into a room containing a bath or shower, or where steam may be present. The fire has been
designed to fit into a builders’ opening or fireplace conforming to BS 1251 (and meeting certain dimensional requirements), which has
been lined with a 125mm diameter flexible flue liner.The firebox must be installed onto a suitable non-combustible insulating surface at
least 12mm thick, covering the entire base area of the firebox. The flue must have an effective height of at least three metres, as meas-
ured from the bottom of the appliance to the top of the flue. Any flue damper plates or restrictors should be removed and no other
restriction fitted to the flue. Where removal is not practical, the restriction must be fixed in the fully open position.
The fire is suitable for twin wall 125mm diameter flue and flue liner which fits directly on to the appliance. If previously used for solid
fuel or oil burning, the flue and chimney must be swept prior to appliance installation. The flue must be checked before installation by
using a smoke pellet or similar to ensure proper draw and that leakage is not evident at any joints. Repair and re-test as necessary before
the appliance is installed. The flue must be connected to only one fireplace, and the flue must not vent more than one appliance (i.e. not
shared with a gas back boiler). There must be no opening in the flue apart from the one that the appliance is installed into, and the one
venting the gases into the air. A suitable terminal may be fitted, such as class GC1, as regulations allow.
Model Country of
estination Cat Gas Type
Operating Pressure
(±2.0 mbar)
Max Energy
Input (kW)
Min Energy Input
(kW)
G20 G25 G30 G31 Gross Net Gross Net
Wall inset slide control models GB - IE I2H Natural Gas 20 - - - 3.8 3.4 2.0 1.8
Wall inset remote control models GB - IE I2H Natural Gas 20 - - - 3.8 3.4 2.0 1.8
Wide wall inset slide control models GB - IE I2H Natural Gas 20 - - - 4.4 4.0 2.2 2.0
Wide wall inset remote control models GB - IE I2H Natural Gas 20 - - - 4.4 4.0 2.2 2.0
The efficiency of this appliance has been measured as specified in BS 7977-1:2009 +A1:2013 and the result is 63%. The gross calorific
value of the fuel has been used for this efficiency calculation. The test data from which it has been calculated has been certified by bsi
(0086). The efficiency value may be used in the UK Government’s Standard Assessment Procedure (SAP) for energy rating of
dwellings.

4.0 SITE REQUIREMENTS - CONTINUED GB IE
4
Whilst a hearth is not required under regulations, it may be adviserable to fit a hearth as a tactile barrel against “walk on” or clothes
drying.
Any existing under grate draught device must be sealed off. The fireplace wall must be non-combustible.
A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.
A non-combustible shelf may be fitted to within 10mm of the top edge of the fireframe. Combustible materials, such as wood, may be
fitted to within 100mm of either side of the fireplace opening, providing the forward projection does not exceed 100mm. Any com-
bustible side walls must be at least 500mm to the side of the radiant heat source. As with all heating appliances, any decorations, soft
furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper) positioned too close to the appliance may discolour or scorch.
The wall for 300mm above the fireplace must be of a non combustible material able to withstand 120°C. Such as cal-
cium silicate board, brick or stone.
Note: dimen ion in italic refer only to wide wall in et
model .
‘A’. Opening height: 530mm - 535mm.
‘B’. Opening width: 567mm min/587mm max. (867mm
min/887mm max).
‘C’. Mounting depth: minimum 250mm.
‘D’. The distance from the floor must be 100mm or greater.
Maximum depth of shelf Minimum distance from bottom of the appliance
surface to underside of shelf
100mm 745mm
150mm 845mm
203mm 895mm
© 2017 Focal Point Fires plc.
‘A’
‘B’
‘C’
‘D’
Figure 1

Note: Ensure that the gas supply is isolated before commencing installation of the appliance.
The fireplace opening and environment must
be in compliance with specifications laid down
in the appropriate sections of these instruc-
tions.
Remove the appliance from it’s carton as
described previously and lay the appliance on
its back, on a dust sheet or similar. Place the
decorative frame, logs, ceramics and fixings
safely to one side. Remove the hood from the
assembly by removing the retaining screws
either side of the hood. See figure 2.
Next, remove the glass assembly by unscrewing the screws in each of the corners.
No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the
same room or space must be taken into consideration when assessing ventilation. If spillage is detected when commissioning the appli-
ance, then amongst other problems there may be insufficient natural ventilation for correct operation of the flue. If the appliance does
not spill with the windows open, but spillage is detected with the windows closed, this demonstrates a lack of natural ventilation. If
spillage is still detected with the windows open, the flue is at fault. Installation of an air brick is the best solution to lack of ventilation.
Any ventilation fitted must comply with BS 5871 part 2 and BS 5440 part 2. Vents fitted under or within the immediate vicinity of the
appliance must not be used as adverse effects to the operation of the O S may occur. Spillage detected during commissioning is almost
always a result of poor flue performance that cannot be corrected by any amount of ventilation. For Republic of Ireland ventilation may
be required, see IS 813, ICP3, IS 327, and any other rules in force.
5.0 VENTI ATION GB IE
6.0 UNPACKING THE APP IANCE
6.1 COMPONENT CHECK IST
QUANTITY DESCRIPTION
1 Firebox and burner tray assembly
1 ecorative frame
1 Flue adapter assembly
3 Individual ceramic logs (Wall inset models only)
10 Individual ceramic logs (Wide wall inset models only)
1 Fixing kit; 4x screws 4x wall plugs
1 Sealing grommet
1 Remote control Handset (Remote control models only)
1 Set of manufacturers instructions
4 M5 screws
1 Tiled ceramic set (2 x side tiles & 1 x back tile)
2 No.8 x 5/16” screws
2 “L” brackets
2 M4 screws
5© 2017 Focal Point Fires plc.
Remove the outer packaging, remove any instructions. Read ALL these instructions before continuing to unpack or install this appliance.
Lift off the remaining packaging components and remove the contents of the box. Check that the components supplied correlate with
the component checklist. Please dispose of all the packaging materials at your local recycling centre.
7.0 PREPARING THE APP IANCE
Figure 2 Figure 3

Remove the burner unit by removing the two
screws either side of the burner as shown in
figure 4.
The tray is now free, and may be lifted away.
Remove the internal firebox from the external
firebox via the six screws highlighted in figure 5.
SUPP Y PIPE ENTRY (All models):
Knockout holes are provided in the rear, the
sides and the bottom of the firebox for use
where concealed pipework is required. Where
necessary, knock out the appropriate hole with
a sharp tap from a hammer, and fit the rubber grommet supplied. A small incision can now be made in the rubber to slip snugly
around the outside of the pipe and sleeving. Do not install or use the appliance without the seal in place. If a hole is inad-
vertently opened, reseal with an intact grommet. Failure to fit the seal correctly will cause flue suction to act upon the area under
the burner, resulting in poor performance and intermittent cutting out of the burner.
7.0 PREPARING THE APP IANCE - CONTINUED GB IE
6© 2017 Focal Point Fires plc.
FIN:
A
 

7.1 PREPARING THE OPENING
Before installing the fire, check the flue using a smoke pellet. All of the smoke should travel up the flue and exit correctly from the ter-
minal. If problems are found, O NOT fit the fire until corrective action is completed. Before running the gas supply into the opening,
offer up the firebox to the fireplace opening to check the fit is good. Ensure that it slides in correctly, the sealing face sits flat and square
to the wall or infill panel, and that the base is firm on the floor of the opening as no leaks are permissible here. At this stage it is essen-
tial to ensure that the outlet of the fire is not restricted in any way. Remove the firebox and take any necessary measurements before
making good and preparing for final installation.
SCREW FIXING : For fixing the appliance to the wall, mark and drill the relevant holes in the firebox on the wall. Insert the wall plugs
into the wall. Insert the firebox back into its correct position and fasten the firebox to the wall using the screws provided.
GAS SUPP Y : Following preparation for the fixing method, the concealed gas supply, where required, can now be put into place. Refer
to the gas supply section for suggested pipe routes. The ends of the sleeving in which the gas pipe is run should be sealed. The ends of
the 8mm supply pipe should be temporarily sealed to prevent the ingress of debris during fixing.
P EASE NOTE: Ensure fire can be removed for ease of servicing and not siliconed.
When the opening is ready for installation of the fire, the gas supply may be routed as per the examples shown in figure 6.
IMPORTANT - Wherever a concealed connection is made a rubber grommet must be used to seal the firebox.
The gas pipe must be suitably protected where it passes through fireplace openings. Any sleeving should be sealed to the pipe at its ends.
This appliance is fitted with an inlet restrictor elbow. Using 8mm diameter pipe, connect the appliance to the gas supply point. The appli-
ance must be fitted with rigid or semi-rigid pipe of 8mm external diameter. The appliance is factory fitted with an inlet restrictor elbow.
Use a minimum length of 8mm pipe, less than 1.5m where possible, as a long run of pipe may cause an unacceptable drop in the supply
pressure.The open end of the supply pipe should be sealed temporarily during the installation of the firebox to prevent the ingress of
dirt and dust. Soldered joints are not recommended.
7.2 GAS SUPP Y ROUTING
FIN:
A
 

Knockouts
Knockout
Figure 4
Figure 6
Figure 5

7© 2017 Focal Point Fires plc.
7.3 INSTA ING THE FIREBOX
Remove any protective film coatings from the finished/decorative surfaces of the appliance. After having selected the final mounting posi-
tion of the appliance, taking into account the requirements as specified in sections 3 and 4
of these instructions, the integrity of the wall, and the feasibility of the proposed supply pipe
routing, the firebox of the appliance may be secured to the wall.
To ensure customer safety, be sure to design the installation so that the strength of both
the wall and any wall fixings used are sufficient.
Focal Point Fires plc. assumes absolutely no responsibility for injuries and/or damages that
may occur due to improper installation or handling. The appliance should not be installed
until all wet plastering and/or dry wall sanding and wall painting has been completed. o
not block the ventilation holes of the appliance.
The wall onto which the appliance is installed must be flat. Install only on a vertical surface.
Avoid sloped surfaces. Installation onto anything other than a vertical wall may result in fire,
damage or injury. If the appliance is to be mounted on the inner leaf of a conventional cavity brick wall, or a solid wall, then the wall
plugs and fixing screws provided may be used. epending on the condition of the wall it may be necessary to use additional fixings. In
this situation, any additional fixings and wall plugs should be of the same size and type as the ones pro-
vided. At the appropriate stage of the installation, drill four holes using only a 8mm masonry bit to a
depth of 42mm. Insert the wall plugs provided ensuring they are flush to the wall.
The wall should be strengthened using appropriate building materials.
If there is no alternative than to rely on some plasterboard fixings then special cavity screw fixings or
hollow wall anchors will be required which are not supplied with this product. These should be con-
structed from metal and not plastic and of the design indicated in figure 7.
The wall where the appliance is
to be installed must be capable
of long-term support of the total
load of the appliance. Measures
should also be taken to ensure
sufficient strength to withstand
the force of earthquakes, vibra-
tion and other external forces.
WARNING
Figure 7
GB IE
Fixing the appliance - All Models
Offer the appliance into the opening to ensure a
good fit, once in the final position mark the posi-
tions shown in figure 8 on the wall. If a concealed
gas connection is to be made ensure the gas sup-
ply pipe is in its final position and can enter the
appliance in the correct position when the appli-
ance is installed into the opening.
rill the wall as appropriate for the type of wall
as previously described in this section, and insert
the chosen type of wall fixings. Insert the wall fix-
ing screws into the top wall plugs.
Insert the lower fixing screws into the lower wall
plugs through the corresponding fixing holes in
the lower part. Locate the flue through the top of
the firebox and attach the bottom of the flue liner
to the flue adapter. Seal the two together using
self tapping screws and aluminium tape (not sup-
plied).
Screw the flue adapter to the top of the exter-
nal firebox, ensuring the flue is still attached in
the correct position.
Next, using the guides in the top of the left hand
and right hand of the external firebox, guide the
internal firebox into position. Once in position,
screw the 6 self tapper screws and 2 M4 screws
at the top to secure the two fireboxes together.
FIN:
A
 

FIN:
A
 

Figure 8 Figure 9
FIN:
A
 

Figure 10 Figure 11
7.4 INSTA ING THE CERAMIC TI ES
FIN:
A
 

FIN:
A
 

Carefully insert the rear brick panel into the rear of
the firebox, behind the bottom lip. Ensure the brick
effect is in the correct orientation,with the lip on the
top edge.
Install one side brick panel in the left hand side of the
firebox, behind the bottom return.
Install the right hand brick panel in the same manner
(the brick effect panels are not labelled). Ensure the
brick effect is in the correct orientation, with the lip
on the top edge, so the brick effect is continuous
around the firebox.
Next screw the “L” ceramic clamps into position in
both side of the firebox with the self tapping screws.
Figure 12 Figure 13

The spark gap (shown in figure 15) between the spark electrode and the thermocouple
should be 3.5 - 4.5mm to produce a good spark.
There should be no need to adjust this.
If under any circumstances the electric spark fails, the pilot may be lit manually by proceed-
ing with the ignition sequence as previously described, and after sliding the control knob
through the spark position, the knob should be held fully to the right and the pilot lit with
a taper.
7.6 GAS CONNECTION
Important Note: Check the thermocouple nut connection into the rear of the valve is secure.
Temporarily fit the burner unit and ensure a suitable gas route can be achieved. Purge the gas supply thoroughly to remove air and
dirt/debris before connection. isconnect the inlet restrictor elbow from the inlet pipe.
Connect the previously installed gas supply to inlet restrictor elbow. Place the burner unit into the firebox making sure that the rear of
the burner bracket fits into the rear of the firebox. Fit the two screws through the burner support brackets to secure the burner assem-
bly into position. Re-fit the restrictor elbow to the inlet pipe of the appliance.
8© 2017 Focal Point Fires plc.
7.5 INSTA ING THE BURNER GB IE
Replace burner unit by screwing the two screws either side of the burner as shown in
figure 14.
FIN:
A
 

Figure 14
8.2 INSTA ING THE CERAMICS
For installation of the fuel bed layout, refer to sections 7.0 and 7.1 of the user instructions.
Figure 15
Spark gap
8.1 SPARK GAP
8.0 TESTING AND COMMISSIONING
Turn on and test the gas supply up to the fire for any leaks, in accordance with current edition of BS6891.
When the appliance is first used, protective oils coating the burner may burn off. It is advisable to ventilate the room during this period
for at least one hour.
8.3 ASSEMB ING THE APP IANCE
Re install the glass assembly, by screwing the screws in each of the corners of the glass
assembly.
Figure 16

9© 2017 Focal Point Fires plc.
For operating instructions for the appliance please refer to sections 5.0 and 5.1 of the users instructions.
8.4 OPERATING THE APP IANCE GB IE
Release the pressure test point screw, and attach a pressure gauge. Light the fire on the
HIGH setting. To commission the appliance, the operating pressure must be in accordance
with the figures stated in section 2.0 of these instructions. The fire is factory set to achieve
the correct flow rates at the specified inlet pressure.
Any significant variation in the inlet pressure could indicate a supply problem. If the inlet
pressure is too high, the gas supply meter/governor may be set incorrectly. This should be
checked with the fire running and if necessary reset by the gas supplier. If the inlet pressure
is too low, then check the meter/governor pressure with the appliance running. If this is less
than the inlet pressure stated in section 2.0 of these instructions it will need to be reset by
the gas supplier. If the inlet pressure is too low, but the meter/governor pressure is accept-
able, then a problem in the supply pipework is to be suspected. Upon satisfactory checking
of the inlet pressure, turn the fire off, disconnect the pressure gauge and refit the test point
screw. Light the fire and check for gas soundness. In the event that the inlet pressure is not
in accordance with the figures stated in the data section of these instructions, the appliance must not be commissioned, and the prob-
lem investigated and rectified.
Slide control models : The pressure test point is located on the left hand side of the burner.
Remote control models : The pressure test point is located on the left hand side of the burner.
Release the pressure test point screw, and attach a pressure gauge. Light the fire on the HIGH setting. To commission the appliance, the
burner pressure must be in accordance with the figures stated in section 2.0 of these instructions.
The fire is factory set to achieve these pressures and any significant variation could indicate a supply problem. If the pressure is too high,
the gas supply meter may be set incorrectly. This should be checked with the fire running and if necessary reset by the gas supplier.
Upon satisfactory checking of the burner pressure, turn the fire off, disconnect the pressure gauge and refit the test point screw. Light
the fire and check for gas soundness. In the event that the burner pressure is not in accordance with the figures stated in the data sec-
tion of these instructions, the appliance must not be commissioned, and the manufacturer should be contacted for guidance.
8.5 OPERATING PRESSURE - S IDE & REMOTE CONTRO S
Figure 17
8.6 F UE SPI AGE MONITORING SYSTEM
This fire is fitted with a flue spillage safety device (O S). If the fire shuts down during use for no apparent reason then several things
may be suspected. If a door or window has been opened creating a draught, then pilot disturbance is the problem, and removal of the
draught should resolve this. The gas pressure reaching the fire must also be checked (again, recall your installer to check and rectify any
problem). The thermocouple connection into the back of the gas control valve may also have worked loose during installation, simply
get the installer to tighten. If pilot disturbance is not the cause, then the O S safety system may be in operation. Switch the appliance
OFF, check the flue and carry out any remedial work required. Relight the fire and carry out a spillage test.
O NOT allow the appliance to be used if it continues to fail a spillage test. The aeration hole of the pilot must be carefully cleaned out
on each annual service to ensure continued function of the O S.The spillage monitoring system shall not be adjusted, modified, or put
out of operation by the installer. Any spare parts fitted MUST be of a type supplied for the purpose by the appliance manufacturer. If the
fire is not spilling, then further guidance should be sought, using the Troubleshooting section as a guide.
8.7 TESTING FOR SPI AGE
Match
Crimp
Tube
Figure 18 : Cross section of
smoke match tube
Make a smoke match tube from
10mm diameter tube. Seal off one
end and crimp the tube to prevent
the smoke match from sliding down
inside.
Figure 19 : Note; insert the smoke match tube
centrally
Figure 20 : Section view of the draft diverter
Note; insert smoke match tube until the end of the
tube touches the draft diverter baffle
Let the fire run on HIGH for five minutes. Take a smoke match and put in the smoke match tube. Light the smoke match and position
the end of the smoke match tube centrally next to the draught diverter as shown in figures 19 and 20.

With the four self tapping screws, screw the hood back into position. See figure 21.
10 © 2017 Focal Point Fires plc.
8.9 FITTING THE DECORATIVE FRAME ASSEMB Y
Remove the facia panel from any protective
packaging.
The facia panel is supported by four M6
screws which protrude from the front of the
firebox.
Ensure each screw is unscrewed approxi-
mately one turn from the fully screwed in
position in order to create a 2mm gap
(shown in figure 22). Hang the facia panel onto the firebox
ensuring that the corresponding keyhole shaped holes engage the screw heads
fully.
2mm
Figure 23
Figure 22
All the smoke should be drawn away up the flue.
Any smoke returning into the room indicates that spillage is occurring.
If the spillage test fails and the spigot restrictor is fitted, remove the spigot restrictor, re-fit and re-test. If the initial spillage test fails, run
the fire for a further 10 minutes and repeat the test. When the test has been completed satisfactorily, repeat with any extractor fans in
the premises running on the highest setting, and any communicating doors open. Finally, repeat with all doors open.
DO NOT allow the fire to be used until the test is satisfactorily passed. Once the test has passed re install the hood
and decorative frame.
8.7 TESTING FOR SPI AGE - CONTINUED GB IE
8.8 FINA ASSEMB Y
Figure 21
9.0 BRIEFING THE CUSTOMER
All instructions must be handed to the user for safekeeping. Show the customer how to light and control the fire. After commissioning
the appliance, the customer should be instructed on the safe use of the appliance and the need for regular servicing. Frequency of serv-
ice depends on usage, but MUST be carried out at least once annually. Advise that cleaning of the fire may be achieved when the fire is
cold. Please refer to section 9.0 of the user instruction manual.
Scratched and other superficial damage to the matt black paintwork of the appliance can be covered with matching heatproof spray. Use
only the manufacturers’ recommended spray paint. Paint only when the fire is OFF and cold. Always mask off the surrounding area to
prevent contamination with overspray. Ventilate the room during the use of the spray. O NOT attempt to spray paint the ceramics, or
wash them in water.
Advise that the fire will emit a “newness” smell for a time after initial commissioning and that extra ventilation may be needed during
this time. Advise that the fire is fitted with a spillage safety device (O. .S.). If the fire shuts down, this system may be in operation. If
spillage is suspected, SWITCH APPLIANCE OFF and call in the installer to investigate any problems.

11 © 2017 Focal Point Fires plc..
10.0 SERVICING
1. Lay out the dust sheet and tools.
2. Carefully remove the decorative front. (see section 8.9)
3. Remove the hood (4 screws).
4. Remove the glass door assembly (4 screws) and clean carefully.
5. Remove the ceramics and clean carefully as described in section 10.1
6. isconnect the gas supply, and remove the two securing screws holding the burner tray in position.
7. Remove the burner tray.
8. Remove the firebox as described in section 10.5.
9. Check the fireplace opening for rubble accumulation and remove. If debris is excessive, initiate remedial work on the flue.
10. Check the flue with smoke pellet for correct operation.
11. Refit firebox using new seals where necessary.
12. Strip off the burner pipes and clean thoroughly.
13. Clean out the injector, pilot assembly and burner tube. O NOT attempt to remove the pilot injector.
14. Re-assemble and re-fit the burner tray.
15. Turn on the gas supply, and leak test.
16. Refit the ceramics, glass door assembly.
17. Check any purpose provided ventilation is un-obstructed.
18. Light the fire and test for spillage.
19. Install the hood and the decorative front.
20. Check setting pressure and safe operation of the appliance.
For specific servicing instructions, see the relevant sections.
Isolate the fire from the gas supply. Ensure that the fire is fully cold before attempting service. A suggested procedure for servicing is
detailed below
GB IE
10.3 SERVICING THE BURNER
10.1 C EANING THE CERAMICS
10.2 REMOVING THE BURNER
10.4 PI OT ASSEMB Y
Remove the decorative front, the hood and the glass door assembly and place to one side. Remove the ceramic components. Gently
clean in the open air. Be careful not to create dust from the logs. Where necessary replace damaged components with genuine spares.
Seal scrap ceramic components in plastic bags and dispose at proper refuse sites as directed.
Re-fit the logs by referring to the relevant section of these instructions.
Remove the decorative front, the hood and the glass door assembly and place to one side.
Remove the two screws securing the tray to the firebox. Pull tray forward slightly and lift away.
Refitting is the reverse of above, being sure to engage the tray location lugs on the shelf at the rear of the firebox.
Remove the burner unit as previously described. The pilot unit can be removed by withdrawing the tubing nut, the thermocouple nut on
the rear of the valve, and the two securing screws, and lifting away. Remove the tubing nut from the valve end of the pilot pipe, and blow
through to dislodge any debris.
Remove the two tubing nuts on the ends of the gas pipe to the injector elbow and blow clear. The injector pipe can now be checked
for debris. Remove the nut retaining the injector elbow. Blow through the elbow to remove any debris.
The valve is not field serviceable, apart from the pilot filter.
Remove the burner unit as in relevant section and pilot unit as described.
Clean the pilot assembly with a soft brush and blow through. Check the aeration holes are free of any dirt or lint. Clean thoroughly
internally, the connection can be removed from the base of the pilot unit using two spanners to make cleaning easier. o not damage
or try to remove the pilot injector. The unit is factory set and the only check necessary is to ensure the spark gap is correct. See
specifications for gap setting.

12 © 2017 Focal Point Fires plc.
10.5 REMOVING THE FIREBOX
10.6 REP ACING THE BATTERIES (REMOTE CONTRO VERSIONS)
GB IE
Appliance - Ensure appliance is off and cool.
Remove the decorative front as shown in section 8.9
The battery is located in the front of the ignition unit, on the right hand side of the burner
(shown in figure 25). Unscrew the battery holder cap. Insert 1 x AA (1.5 volt) battery and refit
cap.
10.7 REP ACING THE BATTERIES (S IDE CONTRO VERSIONS)
11.0 TROUB ESHOOTING GUIDE
Fire park but pilot doe not light • No gas to fire, check isolators are open and gas supply is on.
• Pipework blockage, clean out.
• Air not fully purged, re purge supply or wait longer.
• Spark earthing to metalwork, reset gap correctly.
• Blocked pilot, clean out internally.
Pilot light but then goe out • Severe restriction in gas supply: clear obstruction.
• Faulty thermocouple, replace pilot unit.
• Blocked pilot, clean out.
• Blocked lint gauze, clean.
• Hold control knob in for longer.
• Check control knob does not foul indicator plate.
• If the pilot will not stay lit there could be a problem with contamination of the
gas supply, drafts,ventilation or the thermocouple needs replacement.
Modifications are dangerous and can have a serious unseen effect on safety.
NEVER MODIFY OR BEND THE THERMOCOUP E TO MAKE THE PI OT STAY A IGHT
Fire doe not park at pilot • HT lead detached, refit.
• Check the spark gap (see section 8.1).
• Faulty piezo unit, replace.
• ebris shorting out electrode, clean.
• Spark shorting to metalwork under tray, check routing of HT lead under burner.
Fire run for a time and then cut off • Loose or faulty thermocouple, rectify.
• Blocked pilot, clean out.
• Excessive drafts in the room.
• Excessive flue pull.
• Fire is too close the an air vent.
• Fire is sited on disused chimney breast which has not been adequately sealed up.
• irt or lint in pilot aeration hole or on the lint gauze, clean thoroughly.
Remove the burner unit as described previously. Protect the opening from potential damage. Remove the screws holding the inner
firebox into position. Remove the four screws holding the flue adaptor into position. isconnect the flue. Next, unscrew the external
firebox from the wall. The firebox is now released from the opening and can be slid outwards. Inspect the fireplace opening for debris
and if excessive rectify the flue before proceeding further. Check the seal around the fireframe and if necessary replace. Refitting of
the firebox is as described in the fitting section of these instructions.
WARNING! DO NOT USE META TOO S TO REMOVE THE BATTERIES. WARNING! The
battery clip must not come into contact with metal parts after unplugging the external battery
holder, because there is voltage sorted in the Receiver.
Handset - Remove cover from rear of handset and insert 1 x ‘PP3’ (9 volt) battery - Replace
cover
Appliance - Ensure appliance is off and cool.
Remove the decorative front as shown in section 8.9 of the installers instruction manual.
The receiver is located towards the right hand side, underneath the burner unit, unscrew the
two screws holding the cover in position. Then remove the cover from the battery pack and insert
4 x ‘AA’ (1.5 volt) batteries - Replace cover.
Figure 25
FIN:
A



X
Figure 24

13 © 2017 Focal Point Fires plc.
11.0 TROUB ESHOOTING GUIDE - CONTINUED GB IE
Fire run for a time and then cut off • If the pilot will not stay lit there could be a problem with contamination of the
gas supply, drafts, ventilation or the thermocouple needs replacement.
Modifications are dangerous and can have a serious unseen effect on safety.
NEVER MODIFY OR BEND THE THERMOCOUP E TO MAKE THE PI OT STAY A IGHT
Pilot flame hrink when fire i on high • Poor gas flow to fire, check pressure with fire on high.
• If pressure is low, remove any restriction in pipework or valve.
• Check all isolators are adequately sized and fully open.
• Check meter pressure is adequate.
• Firebox grommet seal missing, rectify.
• If the pilot will not stay lit there could be a problem with contamination of the
gas supply, drafts, ventilation or the thermocouple needs replacement.
Modifications are dangerous and can have a serious unseen effect on safety.
NEVER MODIFY OR BEND THE THERMOCOUP E TO MAKE THE PI OT STAY
A IGHT.
Fire mell when fir t lit or in u e • Newness smell from brand new appliance.
• Spillage occurring. Carry out Spillage test and rectify any problems.
• Combustible materials used in incorrect positions.
• Firebox grommet seal missing, rectify.
•Other airborne contaminants such as dust, tobacco smoke, paint vapours.
11.1 TROUB ESHOOTING GUIDE - REMOTE CONTRO
Will not operate with hand et • Transmitter batteries low, replace Transmitter batteries. Quality alkaline recommended,
• Receiver batteries low, replace Receiver batteries with 1.5v “AA” quality alkaline batteries.
• Optional Mains Adapter not operating properly, check Mains Adapter.
• Check coding of Transmitter and Receiver (initial sync), learn new code (reset). See label
on Receiver.
•Transmitter distance limited, straighten the antenna. Replace Receiver, see wiring diagrams.
No transmission: (motor does not turn) • ead batteries, replace batteries in the Receiver and/or Remote Handset (quality Alkaline recommend
ed) WARNING! DO NOT USE META TOO S TO REMOVE THE BATTERIES.
WARNING! The battery clip must not come into contact with metal parts after unplug
ging the external battery holder, because there is voltage sorted in the Receiver.
• Receiver must learn new code. Press and hold the Receivers reset button until you hear
2 acoustic signals. After the second, longer acoustic signal, release the rest button. Within the
subsequent 20 seconds press the (small flame) button on the Remote Handset until you
hear two additional short beeps confirm the new code is set.
• Receivers, replace receiver and reprogram code.
• Transmitter, replace the Transmitter and reprogram code.
• Bent pins on the 8 Wire Connector on the Valve and Receivers, Straighten pins on 8 Wire
Connector.
• Wiring at Valve damaged, replace a valve.
•IR-Eye (Infrared remote only), replace (check and change).
No ignition; no tone: • Receiver, replace Replace and reprogram code.
No Ignition; one 5 second continuous tone; • Loose wire, secure wire.
• Receiver, replace receiver and reprogram code.
• Bent pins on the 8 Wire Connector on the Valve and Receivers, Straighten pins on 8 Wire
Connector.
•Valve, replace Valve, do not overtightened the thermocouple interrupter.
Ignition stops after the first spark • Loose ground connection on the valve, check the ground connection at the valve
and tighten screw.
Frequent beeps for 3 seconds while motor • Batteries (receiver) are low, replace batteries (Quality Alkaline recommended).
turns WARNING! DO NOT USE META TOO S TO REMOVE THE BATTERIES.

• The installation and Servicing of this fire MUST only be carried out by a competent person in accordance with local Codes and/or
Regulations, Building Regulations and the manufacturer's instructions. Failure to comply with these could lead to prosecution and invalidate
the appliance warranty. In the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve. This
appliance is only suitable for the gas type for which it is supplied.
• Keep a note of the installer's name and address, the original purchase receipt and the date of installation. Failure to produce this informa-
tion may invalidate the warranty. The appliance should be serviced regularly to ensure continued safe operation. See the servicing section
for further reference. Frequency of service will depend on use, but MUST be carried out at least once annually.
• Parts of this appliance become naturally hot during use. The manufacturer of this appliance considers all surfaces as working surfaces with
the exception of the control knob and control panel.
• As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children, and the elderly or
infirm.
• The appliance should be serviced regularly to ensure continued safe operation. Frequency of service will depend on use, but MUST be car-
ried out at least once annually.
• Combustible items, such as flooring and furniture and soft wall coverings (such as blown vinyl or embossed paper), low temperature sur-
rounds etc may discolour if fitted too close to the fire. See relevant section for further details on clearances to combustibles.
• This appliance incorporates a combustion monitoring system (O S).
• O NOT burn any foreign material on this fire, the ceramic fuel effect components must be of the correct type and laid out in accordance
with the relevant section of these instructions.
• O NOT add extra fuel effects to the fire
• Failure to do so could create a hazard or lead to sooting.
• Before the appliance is installed, the chimney should be swept. All flues should be checked by the installer to ensure there are no defects
or obstructions that may prevent the flow of combustion products.
• This appliance is fitted with a flue blockage safety device which will shut down the fire if abnormal flue conditions occur. It is NOT a sub-
stitute for an independently mounted Carbon Monoxide detector.
• This fire is supplied with a particular style of front. Use of the front will ensure an adequate airflow under the firebed for the correct func-
tioning of this appliance. Use ONLY the front supplied with the appliance. Use of any other front could be dangerous.
U S E R I N S T R U C T I O N S
2.0 C EARANCES TO COMBUSTIB ES
A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.
A non-combustible shelf may be fitted to within 10mm of the top edge of the fireplace opening. Combustible materials, such as wood, may be
fitted to within 100mm of either side of the fireplace opening, providing the forward projection does not exceed 100mm.
Any combustible side walls must be at least 500mm to the side of the radiant heat source. As with all heating appliances, any decorations, soft
furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper) positioned too close to the appliance may discolour or scorch.
1.0 IMPORTANT NOTES
1
GB IE
© 2017 Focal Point Fires plc..
Maximum depth of helf Minimum di tance from the bottom of the appliance to under ide of helf
100mm 745mm
150mm 845mm
203mm 895mm
Section
1.0
2.0
3.0
4.0
5.0
5.1
6.0
7.0
7.1
Content
Important Notes
Clearances to Combustibles
Fireguards
Ventilation
Operating Instructions - Slide Control
Operating Instructions - Remote Control
Flue Spillage Monitoring System
Fuel Bed Layout - Wall Inset
Fuel Bed Layout - Wide Wall Inset
Page No.
1
1
2
2
2
3
7
7
8
Section
8.0
9.0
10.0
10.1
11.0
12.0
13.0
14.0
Content
Servicing
Cleaning
Replacing the Batteries- Remote Controls
Replacing the Batteries- Slide Controls
List of Replacement Parts
Installation etails
Service History
Guarantee - Terms and Conditions
Page No.
10
10
10
10
11
11
11
12

The fireguards specified in BS 8423 are intended to protect people from falling into a fire, prevent burns and reduce the risk of injury, particu-
larly to young children and the infirm. In addition it is intended to reduce the risk of fire resulting from clothing and/or other flammable mate-
rials coming into contact with, or in proximity to, burning fuel and/or hot surfaces.
Fireguards can be permanently fixed in position or can be moveable, and can incorporate open fires including combination grates, or closed fires,
including room heaters and stoves. See figures 1 & 2 for fireguard examples.
The fireguards specified are not intended to reduce the risk of fires caused by flying particles, which are covered by BS 3248.
No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the same space or
room, and the results of a spillage test must be taken into consideration when assessing ventilation requirements, this will have been carried out
by your registered installer.
For Republic of Ireland, ventilation may be required, see IS 813, ICP3, IS 327, and any other rules in force.
WARNING : Ventilation openings (where fitted) must never be blocked or restricted in any way.
The control knob is located under the centre of the appliance.
The pilot is visible through the centre of the burner.
Move the slide control knob fully right to the SPARK position, and hold there for a few seconds, until
the pilot light stays on. When the pilot light has established, release the slide control knob and it will
return to the LOW flame setting. If the pilot is extinguished during use, wait three minutes before
repeating the ignition procedure.
To achieve the HIGH setting, move the slide control knob left to the HIGH flame setting. To turn the
fire OFF, move the slide control knob left fully to the position marked ‘O’.
2© 2017 Focal Point Fires plc.
3.0 FIREGUARDS GB IE
Figure 1
Example of moveable fireguard for portable heating appliances
Key
1. Optional base section for total enclosure of a wall mounted appliance
2. Points for attachment to a wall.
Figure 2
Example of detachable fireguard
Key
1. etachable fireguard
2. Screw eye
4.0 VENTI ATION
5.0 OPERATING THE FIRE - S IDE CONTRO MODE S
 

Figure 3

TO TURN ON APPLIANCE
When pilot ignition is confirmed, motor turns automatically
to maximum flame height.
Simultaneously press the OFF and
(large flame) buttons until a short beep
confirms the start sequence has begun;
release buttons. Continuing beeps
confirm the ignition is in process.
Once pilot ignition is confirmed, there
is main gas flow.
After main burner ignition the handset
will automatically go into manual mode
(CSA version, CE version).
WARNING!
If the pilot does not stay lit after several
tries, turn the main valve knob to OFF
and follow the instructions “Turn Off
Gas to Appliance” (page 20).
FLAME HEIGHT A JUSTMENT
Handset
In standby mode: Press and hold (large
flame) button to increase flame height.
5.1 OPERATING THE FIRE - REMOTE CONTRO MODE S
3© 2017 Focal Point Fires plc.
Handset
Press the OFF button.
TO TURN THE APPLIANCE OFF
STAN BY MO E (Pilot Flame)
Handset
Press and hold (small flame) to set appliance at pilot
flame.
Press and hold (small flame) but-
ton to decrease flame height or
to set appliance at pilot flame.
For fine adjustment tap the
(large flame) or (small flame)
buttons.
GB IE
esignated Low Fire and High Fire
ouble-click (small flame) button. “LO” will be displayed.
NOTE: Flame goes to high fire first before going
to designated
low fire.
ouble-click (large flame) button. Flame auto-
matically goes to
high fire. “HI” will be displayed.
ouble-click (large flame) but-
ton. Flame automatically goes to
high fire. “HI” will be displayed.

4© 2017 Focal Point Fires plc.
Modes of operation
Briefly pressing the SET button changes the
mode of operation in the following order:
MAN →TEMP →TEMP →
TIMER →and back to MAN .
TEMP Daytime Temperature Mode
(Appliance must be in standby mode; pilot
ignited)
The room temperature is measured and
compared to the set temperature. The
flame height is then automatically adjusted
to achieve the aytime Set Temperature.
TIMER Timer Mode
(Appliance must be in standby mode; pilot
ignited)
The Timers P1 and P2 (Program 1, Program
2) each can be programmed to go ON
and OFF at specific times. For instructions
see Timer Programming Mode.
NOTE: The display shows the set temperature
every 30 seconds.
SETTING THE TIME
The Time display will flash after either:
a) Installing the battery or
b) Simultaneously pressing the (large
flame) and (small flame) buttons.
Press (large flame) button to set the hour.
Press (small flame) button to set the minute.
Press OFF or simply wait to return to manual
mode.
5.1 OPERATING THE FIRE - REMOTE CONTRO MODE S GB IE
NOTE: Manual mode can also be
reached by pressing either
the (large flame) or the (small
flame) button.
MAN Manual Mode
Manual flame height adjustment.
Setting °C/24 hour or °F/12
hour Clock
Press OFF and (small flame) but-
ton until display changes from
Fahrenheit/12 hour clock to
Celsius/24 hour clock and vice
versa.
Setting °C/24 hour or °F/12
hour Clock
Press OFF and (small flame) but-
ton until display changes from
Fahrenheit/12 hour clock to
Celsius/24 hour clock and vice
versa.
Setting the ON/OFF
Temperatures
Setting the “DAYTIME ”
Temperature
EFAULT SETTINGS: TEMP
(sun), 23 °C/74 °F
Briefly press SET button to
scroll to TEMP TEMP (sun)
mode. Hold the SET button
until the TEMP flashes.

5© 2017 Focal Point Fires plc.
5.1 OPERATING THE FIRE - REMOTE CONTRO MODE S GB IE
Press (large flame) button to increase
aytime Set Temperature.
Press OFF or simply wait to complete pro-
gramming.
Press (large flame) button to increase
Nighttime Setback Temperature.
Press OFF or simply wait to complete
programming.
Press (small flame) button to
decrease
aytime Set Temperature.
Setting the “NIGHTTIME
SETBACK” Temperature
EFAULT SETTINGS: TEMP
(moon), “ ” (OFF)
Briefly press SET button to
scroll to TEMP TEMP (moon)
mode. Hold the SET button
until the Temperature flashes.
Press (small flame) button to
decrease Nighttime Setback
Temperature.
SETTING Program TIMERs
Default Settings
CE: Program 1: P1 : 6:00 P1 : 8:00
Program 2: P2 : 23:50 P2 : 23:50
CSA: Program 1: P1 : 6:00am P1 : 8:00am
Program 2: P2 : 11:50pm P2 : 11:50pm
2 ON times can be programmed per day.
CE: The day starts at 0:00, ends at 23:50.
CSA: The day starts at 12:00am, ends at 11:50pm.
The ON/OFF times have to be programmed in the order
P1
≤ P1 < P2 ≤ P2 .
If P1 = P1 or P2 = P2 the timer is deactivated.
To have the fire over night, it can be set:
CE: P2 23:50 and P1 0:00
CSA: P2 11:50am and P1 12:00am

6© 2017 Focal Point Fires plc.
5.1 OPERATING THE FIRE - REMOTE CONTRO MODE S GB IE
Select Timer Mode by briefly pressing the
SET button.
Set the hour by pressing the (large flame)
button.
Setting P1 OFF Time
Briefly press SET button to scroll to setting
P1 OFF time. P1 and (moon) are displayed
and the time flashes.
Set the minutes by pressing the (small
flame) button.
Setting P1 ON Time
Hold the SET button until P1
and (sun) are displayed and the
time flashes.
Set the minutes by pressing the
(small flame) button.
Set the hour by pressing the
(large flame)
button.
Setting P2 ON Time
Briefly press SET button to scroll to setting P2 ON time.
P2
(sun) is displayed and the time flashes.
See instructions "Setting P1 ON Time".
Setting P2 OFF Time
Briefly press SET button to scroll to setting P2 OFF time.
P2 (moon) is displayed and the time flashes.
See instructions "Setting P1 OFF Time".
This concludes programming Timers P1 and P2. Press
OFF or wait. The handset will automatically save your
changes.

7© 2017 Focal Point Fires plc.
This fire is fitted with a flue spillage safety device (O S).
If the fire shuts down during use for no apparent reason then several reasons may be suspected. If a door or window has been
opened creating a draught, then pilot disturbance could be the problem, and removal of the draught should resolve this.
The fire can then be re-lit in accordance with the previous section. If pilot disturbance is not the cause, then the O S safety sys-
tem may be in operation. Switch the appliance OFF, call in your installer to check any ventilation and carry out any remedial work
required. O NOT allow the appliance to be used until the installation is passed as safe.
6.0 F UE SPI AGE MONITORING SYSTEM
7.0 FUE BED AYOUT - WA INSET
Figure 4
1. Remove the ceramic logs from their protective packaging. All logs are
marked on the rear or the underside from letters “A” to “C”. Place the log
marked ‘A’ on the top left rear ledge behind the burner mixer chamber as
shown in figure 4.
2. Place the log marked ‘B’ on the top right rear of the burner as shown
in figure 5.
Ensure that both rear logs are pushed back against the rear brick panel.
3. Place the log marked ‘C’ on the front ledge of the burner, behind the
return and in front of the burner mixer chamber.
IMPORTANT : The fire is designed to operate correctly with
the logs supplied when assembled according to the instructions.
Never add to the logs, or change them for a different type.
Never throw rubbish or other matter onto the fuel bed. Due to
the light colour of the logs, some discolouration/sooting is to be
expected during normal use.
GB IE
Figure 5
Figure 6