Ekofires eko 3050 Guide

installation and user instructions
All instructions must be handed to user for safekeeping
Revision B - 03/11
Country(s) of destination - GB/IE
eko 3030 eko 3035
eko 3040 eko 3050
eko 3060 eko 3065
eko 3080 eko 3085
eko 3090 eko 3095
fuel effect gas fire
manual - remote control - slide control

Eko 3030 Eko 3040
Eko 3050 Eko 3060
Eko 3080
Please note : Except where
otherwise stated, all rights,
including copyright in the
text, images and layout of
this booklet is owned by
Focal Point Fires plc. You are
not permitted to copy or
adapt any of the content
without the prior written per-
mission of Focal Point Fires
plc.
Eko 3090
©2011 Focal Point Fires plc.

INSTALLATION INSTRUCTIONS
Preliminary Notes Before Installation
This appliance is an Inset Live Fuel Effect appliance that provides radiant
warmth utilising the latest type burner technology.
The fire is designed to fit various types of fireplaces and natural draught flues
as listed in the Installation Requirements.
The appliance must be installed by a GAS SAFE registered person in accordance
with Gas Safety (Installation and Use) Regulations 1998.
Read all these instructions before commencing installation.
This appliance must be installed in accordance with the rules in force and only
used in a sufficiently ventilated space.
The appliance is designed for installation on to a non-combustible hearth of at
least 300mm depth.
This appliance is factory set for operation on the gas type, and at the pressure
stated on the appliance data plate.
This appliance is available in either a manual control version, a battery powered
remote control version, or a slide control version with a number of fuel effect
options. These instructions cover all control options, and all fuel effect options.
See the relevant sections of these instructions for further details.
Manufactured by : Focal Point Fires plc.
Christchurch, Dorset BH23 2BT
Tel: [phone] Fax: [phone]
www.ekofires.co.uk
e-mail: [email protected]
©2011 Focal Point Fires plc.

IMPORTANT NOTES
This fire is an Inset Live Fuel Effect Gas Fire providing radiant warmth. It is designed to operate on Natural
Gas only.
It is the LAW that all gas appliances and fittings are installed by a GAS SAFE registered person and in accor-
dance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British Standards for
Installation, Codes of Practice and in accordance with the Manufacturers’ Instructions. The installation shall
also be carried out in accordance with the following regulations:
The Building Regulations issued by the Department of the Environment, the Building Standards (Scotland)
(Consolidation) Regulations issued by the Scottish Development Department.
BS 5871 part 2
BS 5440 part 1
BS 1251
BS 6891
BS 6461 part 1
Failure to comply with these regulations could lead to prosecution and deem the warranty invalid.
This appliance must be installed in accordance with the rules in force and used only in a sufficiently
ventilated space.
Consult all instructions before installation and use of this appliance.
This appliance is free from any asbestos material. Refractories and fuel beds are constructed from
ceramic fibre.
Note : Remote control models only
This appliance features a battery-opearated remote control system, and under normal usage will need new
batteries approximately every twelve months.
Remote control Handset requirements - 1 x ‘PP3’ type (9 volt)
Reciever/motor unit requirements - 4 x ‘AA’ type (1.5 volt)
Refer to the appropriate section of these instructions for details of how to change the batteries.
Note : Slide control models only
This appliance features a battery-operated slide control system, and under normal usage will need new bat-
teries approximately every twelve months.
Requirements - 1 x ‘PP3’ type (9 volt)
Refer to the appropriate section of these instructions for details of how to change the battery.
1
Section
1.0
2.0
3.0
4.0
4.1
5.0
6.0
7.0
7.1
8.0
9.0
10.0
11.0
11.1
Contents
Important Notes
Appliance Data
Installation Requirements
Site Requirements
Debris Collection Space
Ventilation
Pre Fabricated Flue Boxes
Unpacking the Appliance
Component Checklist
Preparing the Appliance
Preparing the Opening
Gas Supply Routing
Fitting the Firebox
Installation by Cable Fixing Kit
Page
No.
1
2
2
3
4
4
4
5
5
5
6
6
7
7
Section
11.2
12.0
12.1
13.0
13.1
14.0
14.1
14.2
14.3
14.4
14.5
14.6
14.7
15.0
16.0
17.0
Contents
Fitting the Burner Unit
Fuel Bed Layout
Replacing the battery (slide control models)
Fitting the Firefront / Frame
Gas Connection
Testing and Commissioning
Operating the Fire (manual control)
Operating the Fire (remote control)
Operating the Fire (slide control)
Spark Failure
Setting Pressure
Flue Spillage Monitoring System
Testing for Spillage
Briefing the customer
Servicing
Troubleshooting Guide
Page No.
8
8
8
8
8
8
8
9
9
9
9
10
10
10
10
12
Note - For Republic of Ireland, reference should be
made to the relevant standards governing installa-
tion, particularly in regard to flue sizing and ventila-
tion. See IS813, ICP3, IS327 and any other rules in
force.
1.0
©2011 Focal Point Fires plc.

INSTALLATION REQUIREMENTS
This appliance MUST NOT be installed into a room containing a bath or shower, or where steam may be
present. The fire has been designed to fit into a builders’ opening or fireplace conforming to BS 1251 (and
meeting certain dimensional requirements), or a suitable flue box complying with the constructional
requirements of BS 715. The flue box must be installed onto a suitable non-combustible insulating surface
at least 12mm thick, covering the entire base area of the box.
The flue must have an effective height of at least three metres, as measured from the hearth to the top of
the flue. Any flue damper plates or restrictors should be removed and no other restriction fitted to the flue.
Where removal is not practical, the restriction must be fixed in the fully open position.
A natural draught flue system is required, and if previously used for solid fuel or oil burning, the flue and
chimney must be swept prior to appliance installation. The flue must be checked before installation by using
a smoke pellet or similar to ensure proper draw and that leakage is not evident at any joints. Repair and
re-test as necessary before the appliance is installed.
The flue must be connected to only one fireplace, and the flue must not vent more than one appliance (i.e.
not shared with a gas back boiler). There must be no opening in the flue apart from the one that the appli-
ance is installed into, and the one venting the gases into the air. A suitable terminal may be fitted, such as
class GC1, as regulations allow.
Eko 3030, Eko 3035, Eko 3040, Eko 3050, Eko 3080, Eko 3085, Eko 3090, Eko 3095 models only : This
appliance has been tested for use in a pre-cast block flue complying with BS 1289. In accordance with BS
1289 part 1, pre-cast flues built with directly plastered faces (front or rear) are not correctly installed as to
ensure proper operation with any type of gas fire. In some instances of this flue construction, temperature
cracking of the surface plaster may occur through no fault of the appliance. An air gap or some form of insu-
lation material should be installed to prevent normal flue temperatures from damaging wall surfaces. Pre-
cast flues must be checked for mortar fangs and correct installation of joints, flue sections in loft space and
terminals.
Eko 3030, Eko 3035, Eko 3040, Eko 3050, Eko 3060, Eko 3065, Eko 3080, Eko 3085, Eko 3090, Eko 3095
models : These appliances has been tested for use with circular flues of a minimum internal diameter of
125mm.
This appliance is suitable for use with a “lightweight” surround and back panel of 150OC minimum rating.
2
2.0
3.0
APPLIANCE DATA
Manual control models Remote control models Slide Control Version
Gas Group G20 Natural Gas CAT I2H G20 Natural Gas CAT I2H G20 Natural Gas CAT I2H
Inlet Pressure 20 mbar (+/- 2.0mbar) 20 mbar (+/- 2.0mbar) 20 mbar (+/- 2.0mbar)
Max Energy Input (gross) 6.8 kW 6.8 kW 6.8 kW
Min Energy Input (gross) 3.5 kW 3.5 kW 3.5 kW
Pilot Energy Input (gross) 166 W 166 W 166W
Setting Pressure (cold) 15.8 mbar (+/- 1.5mbar) 15.8 mbar (+/- 1.5mbar) 14.5 mbar (+/- 1.5mbar)
Main Injector Burner Stereo 81/Bray cat. 82/420 Stereo 81/Bray cat. 82/420 Stereo 82
Gas Inlet Connection 8mm Inlet Restrictor Elbow 8mm Inlet Restrictor Elbow 8mm Inlet Restrictor Elbow
Gas Control Valve Dungs BM 733/NGC6802 Mertik Maxitrol GV30 series Teddington TESA 3173/001
Ignition Integral Piezo spark Integral Piezo spark Integral Piezo spark
Spark Gap 3.5 to 4.5mm 3.5 to 4.5mm 3.5 to 4.5mm
Weight 20 Kg 22 Kg 21 Kg
Please see Data Badge affixed to appliance for current data.
This appliance is for use only with the gas type, and at the pressure stated on the appli-
ance Data Badge, and is for decorative purposes.
©2011 Focal Point Fires plc.

SITE REQUIREMENTS
The fireplace opening should be inspected and repairs made where necessary. Any chair brick or fireback may
be left in situ, providing that the dimensional requirements for debris collection space and spigot clearances
are met. See diagram below.
Eko 3030, Eko 3035, Eko 3040, Eko 3050, Eko 3080 Eko 3085, Eko 3090, Eko 3095 models only: The open-
ing WIDTH and HEIGHT dimensions should be between 375mm and 450mm wide, and 540mm (see note) to
575mm high. Note: The spigot outlet of the fire is 560mm high, but should fit into the gather at the top of
the fireplace as the appliance is fitted. Any modifications to the fireplace opening must be to a height of
560mm min.Opening DEPTH should be 200mm or greater for a clay/cement lined or pre-cast flue which is
new, unused, or previously used only with a gas appliance. DEPTH should be 240mm or greater for a flue
used for solid fuel of oil burning appliances. Opening DEPTHS include any plaster or infill panels which form
part of the installation.
Eko 3060, Eko 3065 models only : The opening WIDTH and HEIGHT dimensions should be between 390mm
and 440mm wide, and 545mm to 575mm high. Opening DEPTH should be 267mm or greater for a
clay/cement lined flue which is new, unused, or previously used only with a gas appliance. DEPTH should be
307mm or greater for a flue which has been used for solid fuel of oil burning appliances. Opening DEPTHS
include any plaster or infill panels which form part of the installation.
All models : This appliance requires a natural draught flue system which may be one of the following;
225mm x 225mm (9in x 9in) brick or stone.
125mm (5in) minimum diameter lined brick or stone.
125mm (5in) minimum diameter twin wall flue conforming to BS 715.
Pre-cast block flue complying with BS 1289. (Eko 3030, Eko 3035, Eko 3040, Eko 3050, Eko 3080, Eko 3085, Eko 3090,
Eko 3095 models only)
Any existing under grate draught device must be sealed off. The opening wall must be non-combustible.
The appliance requires a hearth with non-combustible surface of at least 12mm thick. The top surface must
be at least 50mm above the surrounding floor level, or be surrounded by a raised edge or fender 50mm high.
To enable the products of combustion to be cleared properly up the flue, the outlet at the back of the appli-
ance must have a 50mm minimum clearance between it and the back wall of the opening or any other
obstruction.
The area immediately above the outlet must form a smoothpath into the flue.
Any type of fire surround used with this appliance must be adequately sealed to the wall and floor.
A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions
given below.
3
A
C
D
B
E
F
4.0
G
H
X
Note : dimensions in italics refer only
to Eko 3060, Eko 3065 only.
A. Opening height: 540mm min/575 mm
max. (545mm min)
B. Opening width: 375mm min/450mm
max. (390mm min/440mm max)
C. Mounting depth: 180mm. (247mm)
D. Hearth must extend minimum of
150mm either side of the opening.
E. Hearth must extend minimum of
300mm in front of the opening.
F. Non-combustible hearth must be a min-
imum of 50mm in height, or be sur-
rounded by 50mm high fender.
G. 470mm, this area must be flat and ver-
tical to ensure a good seal.
H. 585mm, this area must be flat and ver-
tical to ensure a good seal.
X. Debris collection space - See section
4.1 on following page.
Maximum depth of shelf Minimum distance from finished hearth
surface to underside of shelf
100mm (4in) 745mm (29 1/4 in)
150mm (6in) 845mm (33 1/4 in)
203mm (8in) 895mm (35 1/4 in)
©2011 Focal Point Fires plc.

SITE REQUIREMENTS (continued)
A non-combustible shelf may be fitted to within 10mm of the top edge of the fireframe. Combustible
materials, such as wood, may be fitted to within 100mm (4in) of either side of the fireplace opening, pro-
viding the forward projection does not exceed 100mm (4in). Any combustible side walls must be at least
500mm to the side of the radiant heat source. As with all heating appliances, any decorations, soft fur-
nishings, and wall coverings (i.e. flock, blown vinyl and embossed paper) positioned too close to the appli-
ance may discolour or scorch.
DEBRIS COLLECTION SPACE
The mounting depth of this appliance is 180mm. In accordance with BS 5871 part 2, minimum debris col-
lection volumes are required behind the installed appliance. These are shown in the table below and as
dimension X on the fireplace diagram shown previously.
CLAY/CEMENT LINES OR BLOCK FLUE WHICH IS NEW, UNUSED, OR PREVIOUSLY ONLY USED WITH A GAS FIRE.
X Dimension = 20mm
UNLINED FLUE OR CHIMNEY WHICH HAS BEEN PREVIOUSLY USED FOR A SOLID FUEL OR OIL BURNING APPLIANCE
X Dimension = 60mm
VENTILATION
No purpose provided ventilation is normally required for this appliance. The requirements of other
appliances operating in the same room or space must be taken into consideration when assessing ventila-
tion.
If spillage is detected when commissioning the appliance, then amongst other problems there may be insuf-
ficient natural ventilation for correct operation of the flue. If the appliance does not spill with the windows
open, but spillage is detected with the windows closed, this demonstrates a lack of natural ventilation. If
spillage is still detected with the windows open, the flue is at fault. Installation of an air brick is the best
solution to lack of ventilation. Any ventilation fitted must comply with BS 5871 part 2 and BS 5440 part 2.
Vents fitted under or within the immediate vicinity of the appliance must not be used as adverse effects to
the operation of the ODS may occur.
Spillage detected during commissioning is almost always a result of poor flue performance that cannot be
corrected by any amount of ventilation.
For Republic of Ireland ventilation may be required, see IS 813, ICP3, IS 327, and any other rules in force.
PREFABRICATED FLUE BOXES
This appliance can be fitted into a number of proprietary flue boxes provided that the minimum dimensions
given in the diagram below are complied with.
Constructional Note: The frame of the fire,
any back panel or other infill panels, and the
flue box must be sealed together so that there
is no possibility of leakage between them.
Adequate clearances to combustible materials
(e.g. false chimney breast construction) must
be maintained.
The manufacturers’ instructions for fitting
the prefabricated box shall be complied with
at all times.
To fit the fire using the cable fixing kit, some
minor adaption may be necessary for certain
flue boxes. A check should be made to ensure
the firebox does not obscure the flue box out-
let.
The firebox, base of the flue box, and hearth
below may be drilled to allow plugs and screws
to secure installation.
It is important that the sealing requirements of the appliance are met at all times and that the flue box is
well sealed to any back or infill panel.
Note: The DEPTH dimension is inclusive of any back or infill panel.
4
4.0
4.1
5.0
6.0
125mm min internal
dia twin wall flue
Eko 3030, Eko 3035 - Eko 3050 - Eko 3080, Eko 3085, Eko 3090,
Eko 3095 models : 375mm min opening width
Eko 3060, Eko 3065 models : 395mm min opening width
Eko 3030, Eko
3035 - Eko
3050, Eko
3080, Eko
3085, Eko
3090, Eko
3095 models :
250mm min
depth
Eko 3060, Eko
3065 models :
265mm min
depth
Eko 3030, Eko
3035 - Eko
3050, Eko
3080, Eko
3085, Eko
3090, Eko
3095 models :
560mm min
height
Eko 3060, Eko
3065 models :
545mm min
height
©2011 Focal Point Fires plc.

UNPACKING THE APPLIANCE
Stand the carton the right way up, cut the strapping bands and remove the top endcap. Read all the instruc-
tions before continuing to unpack or install this appliance.
Remove the box containing the firefront, and the bags containing the ceramic components. Remove the card-
board packing pieces, and any other bags or boxes containing fittings or other parts. When all loose parts
have been removed, the outer sleeve may be lifted off to reveal the appliance. Check that the components
supplied correlate with the component checklist given in section 7.1. Please dispose of all the packaging
materials at your local recycling centre.
COMPONENT CHECKLIST
QTY DESCRIPTION
1 Firebox and burner tray assembly
1 Decorative cast frame, front and control cover (Eko 3050 & Eko 3080, Eko 3085, Eko 3090, Eko 3095 models only)
1 Decorative extruded frame with detachable control cover (Eko 3040 models only)
1 One piece decorative trim (Eko 3030, Eko 3035 & Eko 3060, Eko 3065 models only)
1 Cast firefront (Eko 3030, Eko 3035 & Eko 3060, Eko 3065 models only)
1 Moulded ceramic fibre combustion matrix
1 Moulded ceramic front strip
16 Individual ceramic coals (Coal models only)
16 Individual ceramic pebbles (Pebble models only)
9 Individual ceramic logs (Log models only)
3 Ceramic brick effect radiant panels (All models excluding Eko 3060, Eko 3065)
2 Ceramic brick panel retaining clips (All models excluding Eko 3060, Eko 3065)
1 Slide control knob and M4 Nyloc nut (Eko 3035 & 3065 Slide control models only)
1 Cable fixing kit; 2 cables, 2 tensioners, 2 cable clamps, 4 eyebolts
1 Sealing grommet
3 Lengths of adhesive sealing strip
1 Self tapping screw pack; 4 No8 x 5/16
1 Set of manufacturers instructions
4 Wall Plugs
PREPARING THE APPLIANCE
Note: Ensure that the gas supply is isolated before com-
mencing installation of the appliance.
The fireplace opening and environment must be in compliance
with specifications laid down in the appropriate sections of
these instructions.
Remove the appliance from it’s carton as described previous-
ly and stand upon a dust sheet or similar. Place the decorative
frame, coals, ceramics and fixings safely to one side. Remove
the burner from the assembly by removing the retaining
screws. The tray is now free, and may be lifted away.
RADIANT PANELS (Eko 3030, Eko 3035, Eko 3040, Eko
3050, Eko 3085, Eko 3085, Eko 3090, Eko 3095, Eko 3085 models only) : The
three radiant panels may now be fixed inside the firebox. Select the plain or pat-
terned side of each panel and insert as follows; Lay the firebox on it’s back. Lay the
tapered panel onto the rear face of the firebox.
The side panels should be fitted by inserting their front edges into the pre-fitted
retaining brackets on the front face of the firebox. Gently align the side panels with
the side of the firebox as shown, over the top of the back panel already in place.
Make sure that the side panels are pushed up firmly to the roof of the firebox, and back firmly to retain the tapered
panel. Make small adjustments to line up the mortar lines if required. Secure the side panels using the small ‘L’
shaped brackets and screws provided (shown inset). The screws should locate into the pre-punched holes in the
sides of the firebox.
SUPPLY PIPE ENTRY (All models): Knockout holes are provided in the rear and sides of
the firebox for use where concealed pipework is required. Where necessary, knock out the
appropriate hole with a sharp tap from a hammer, and fit the rubber grommet supplied.
A small incision can now be made in the rubber to slip snugly around the outside of the
pipe and sleeving. Do not install or use the appliance without the seals in place. If a
hole is inadvertently opened, reseal with an intact grommet. Failure to fit the seal correctly
will cause flue suction to act upon the area under the burner, resulting in poor perform-
ance and intermittent cutting out of the burner.
Eko 3035 & 3065 Slide controls models : The control knob is supplied as a loose part.
Insert the control knob into the hole in the top of the slide control spindle. Secure the con-
trol knob in position using the M4 nyloc nut provided.
5
7.0
7.1
8.0
©2011 Focal Point Fires plc.

PREPARING THE APPLIANCE
(continued)
SPIGOT RESTRICTOR (All models): If installing the fire into
a Class 1 or good Class 2 flue, simply bend up (stitch bend
join) the spigot restrictor into position in the flue outlet of
the fire. You MUST remove (or bend down fully) the spig-
ot restrictor and re-test if the appliance fails a spillage
test during commissioning.
SEALING STRIPS (All models) : Apply the self adhesive
sealing strips to the back of the fireframe to give a continu-
ous seal.
PREPARING THE OPENING
Before installing the fire, check the flue using a smoke pel-
let. All of the smoke should travel up the flue and exit cor-
rectly from the terminal. If problems are found, DO NOT fit
the fire until corrective action is completed.
Protect the decorative hearth whilst pushing the firebox in
and out of the opening. Part of the packaging will make an
ideal hearth saver pad.
Before running the gas supply into the opening, offer up the
firebox to the fireplace to check the fit is good. Angle the
firebox or adjust the spigot outlet as described in the Fitting
the Firebox section. Ensure that it slides in correctly, the
sealing face sits flat and square to the wall or infill panel, and
that the base is firm on the floor of the opening as no leaks
are permissible here.
At this stage it is essential to ensure that the spigot outlet of
the fire is not restricted in any way. Remove the firebox and
take any necessary measurements before making good and
preparing for final installation.
CABLE FIXING : For fixing of the fire by the cable method,
see the relevant section. The cable fixing locations should be
marked on the back of the opening and the holes drilled. Fit
the fibre rawlplugs and eyebolts to these holes. Note: Plastic
rawlplugs are NOT suitable for this application.
SCREW FIXING : For fixing by screw, mark and drill the fireframe or base, and the relevant points in the
opening or on the wall. Rawlplugs will again be required. Pre-punched holes are not provided for this pur-
pose to allow you to choose the optimum positions.
GAS SUPPLY : Following preparation for the fixing method, the concealed gas supply, where required, can
now be put into place. Refer to the gas supply section for suggested pipe routes. The ends of the sleeving
in which the gas pipe is run should be sealed. The ends of the 8mm supply pipe should be temporarily sealed
to prevent the ingress of debris during fixing.
GAS SUPPLY ROUTING
When the opening is ready for installation of the fire, the gas supply can be routed as shown in the diagram
below.
IMPORTANT - Wherever a concealed connection is made a rubber grommet must be used to seal the firebox.
The gas pipe must be suitably protected where it passes through fireplace openings. Any sleeving should be
sealed to the pipe at its ends. This appliance is fitted with an inlet restictor elbow.
The open end of the supply pipe should be sealed temporarily during the installation of the firebox to pre-
vent the ingress of dirt and dust.
6
8.0 Eko 3030, Eko 3035, Eko 3040, Eko 3050, Eko 3085, Eko
3085, Eko 3090, Eko 3095 models
Eko 3060, Eko 3065 models
All models - sealing strips
9.0
10.0
©2011 Focal Point Fires plc.

GAS SUPPLY ROUTING (continued)
Eko 3030, Eko 3035 and Eko 3060, Eko 3065 models : The appliance firefront is notched to allow the gas
pipe to pass through when an over hearth supply is necessary.
Eko 3040, Eko 3050 and Eko 3085, Eko 3085, Eko 3090, Eko 3095 models : If an over hearth supply rout-
ing is necessary, then the supply pipe may be routed beneath the control cover.
FITTING THE FIREBOX
Eko 3030, Eko 3035, Eko 3040, Eko 3050, Eko 3085, Eko 3085, Eko 3090, Eko 3095, Eko 3085 models only
: To fit the firebox, firstly check the fire goes fully back into the opening. If the fire will not fit straight in,
tilt the unit backwards and insert the spigot first to lead in to the gather at the top of the fireplace. If this
is still not possible, remove the spigot outlet screws using a screwdriver, bend it down and partly insert the
firebox. Now push the outlet deflector back up to the original position under the lip of the fireplace open-
ing and secure with the screws. The fire is designed to operate correctly with the deflector screwed in its
original position and spillage problems may arise by not realigning correctly once fitted.Secure the fire box
by drilling and screwing down the frame or base of the firebox, or use the cable fixing method.
Eko 3060, Eko 3065 models only : The firebox may be fitted to the opening by using screw fixing or by the
cable kit as described in the relevant section.Secure the fire box by drilling
and screwing down the frame or base of the firebox, or use the cable fix-
ing method.
INSTALLATION BY CABLE FIXING KIT
Drill the four holes for the rawl plugs, as shown in the diagram. If the fire-
place configuration does not allow the exact layout given, the eyebolts
should be positioned as close to the correct layout as possible.
Before finally fitting cables, ensure the self adhesive sealing strips are in
position on the back of the appliance frame. The fireframe must be sealed
evenly to the fireplace opening all around the periphery.
Thread the tensioning cables through the holes in the top of the firebox, then the eyelets, and finally through
the lower holes in the back of the firebox, as shown in the photographs.
Note: The burner tray MUST be removed as per relevant section to gain
access to the cable adjusters.
Push the appliance back into to fireplace, centralise, and pull the loose ten-
sioning cables through the holes into the firebox. You may need to tem-
porarily adjust the outlet deflector at this point as described in the Fitting
the firebox section. Thread the tensioner bolts onto the cables, with the nuts
screwed down close to the tensioner head. Slide the screwed nipple onto the
cable, pull cable tight, and tighten nipple.
The tension of the cable may now be adjusted by using a suitable spanner
on the tensioner nuts to pull the appliance tightly against the fireplace open-
ing. Visually inspect the seal and reseat if necessary.
Note: DO NOT cut off excess cable. Surplus cable must not be cut off, as it
will be impossible to refit the fire after servicing. Coil up the surplus cable,
and locate at rear of firebox.
Note : If running a concealed gas supply, ensure grommets are secure around incom-
ing pipes.
10.0
11.0
Grommets
Firebox
Fireplace opening
Gas valve
Manual control version
Grommets
Firebox
Fireplace opening
Gas valve
Remote control version
7
A. 250mm
B. 350mm
C. 60mm
Dimensions
+/-10mm
A
B
C
11.1
©2011 Focal Point Fires plc.