ekwb EK-FC970 GTX TF5 TFX Series Manual

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 21th of May, 2014. Revision 1.0
Installation and mounting manual for EK-FC970 GTX TF5 TFX water
block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before
installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual before through before beginning with the installation process!
2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
3. The EK High Flow and EK-CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.
4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION. Sample photo of MSI GeForce GTX 970 Gaming 4G series card.
STEP 2: PREPARING YOUR GRAPHIC CARD.
1. REMOVING STOCK COOLER: Remove encircled screw on the
bracket (required only on certain models):
STEP 2 cont.: PREPARING YOUR GRAPHIC CARD
1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly screws
should be removed, including self-adhesive washers on both sides of the PCB (if present). There are up
to 13 screws on the back of the graphics card.
2. CLEANING THE PCB. Carefully detach the original stock cooler
after removing all screws securing it to the board. Wipe off the
remains (by using non–abrasive cloth or q-tip , as shown on sample
photo) of the original thermal compound until the components and
circuit board are completely clean. EKWB recommends the use of
denatured alcohol for removing TIM leftovers.
3. APPLYING THERMAL COMPOUND. Wipe off the
remains (by using non–abrasive cloth or q-tip ) of the
original thermal compound until the components and
circuit board are completely clean. Apply thermal
compound: lightly coat NVIDIA GPU chip with enclosed
EK-TIM Ectotherm thermal grease. EKWB recommends
to apply thermal grease in cross form for best
performance (see sample picture).
4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which are already pre-cut. Others
have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers. PLEASE
REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.
Replacement thermal pads:
Thermal Pad D –0.5mm (RAM 8x)
Thermal Pad A –0.5mm (100x16mm)
Thermal Pad A –1.0mm (100x16mm)
STEP 3: INSTALLING THE WATER BLOCK
1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than
enough pads to cover all surfaces that need to be covered to make block fully functional). EKWB recommends using small drops of electrically non-conductive (for
example: Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme™) thermal grease on each phase regulator (that is being covered with thermal pad) in order to even
further improve the thermal performance of the EK-FC970 GTX TF5 TFX series water block.
1: Thermal pad D –0.5mm
(for memory IC):
2: Thermal pad A –0.5mm
(for Vdd VRM/MOSFET):
1
1
1
1
3
2
3: Thermal pad A –1.0mm
(for main VRM/MOSFET):

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 21th of May, 2014. Revision 1.0
2. PLACING THE BLOCK ON TO THE GRAPHICS CARD. Carefully position the
water block with preinstalled 2.5 mm standoffs on to the graphics card. During this
process please make sure you align mounting holes on the PCB with holes on the
water block (same applies for other tops). Also pay attention not to use too much
force by pressing the block down to the PCB. Chip dies are prone to cracking.
3. ATTACHING THE BLOCK TO THE GRAPHIC CARD. Use a Philips screwdriver
screw with the enclosed M3x4 DIN 7985 screws. EKWB recommends users to start
tightening the screws around the GPU core and continue outwards. Always use a
plastic washer under each and every screw! If the washer is already present on the
circuit board (usualy around the four GPU core screw holes) there is no need for
additional washer.
STEP 4: CHECKING FOR CONTACTS
If necessary temporarily r emove the water block to check for uniform surface contact between the block and the components, pay special attention to the VRM section of
the graphics card. Check whether the water block makes contact with the intended integrated circuit. Then repeat sub-steps in previous section to re-attach the block. In
case you fail to obtain good contact, please check again that your thermal pad thickness or contact our support service at
http://www.ekwb.com/support.
STEP 6: INSTALLATION OF FITTINGS AND TUBING
Screw in the two G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-CSQ
fittings with the EK-FC970 GTX TF5 TFX series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an
appropriate substitute.
You can use any opening as an inlet/outlet port. Do not forget to plug the remaining two opening with enclosed EK-Plug G1/4 or equivalent.
CAUTION: In case of using connectors other than EK-CSQ series compression fittings, take special attention to the length of the fittings’ male G1/4” thread. 5mm is the
maximum allowed G1/4” thread length!
STEP 7: INSERTING THE CARD IN YOUR PC CASE
Carefully lift your graphics card with installed block and insert it in your PC’s motherboard PCI-express expansion slot. Please bear in mind that your graphics card is probably
heavier than when it was equipped with original heat sink fan assembly. One needs to be very careful when handling the graphics card. Avoid all un-needed manipulation of
the VGA/water block assembly that might damage your card or water block during final installation.
REQUIRED TOOLS:
scissors Philips head screwdriver
Screw M3x4 DIN 7985
Plastic washer
EK-CSQFitting
Tubing
EK-Plug G1/4
Acetal Terminal