ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox User manual

USER GUIDE
GPU WATER BLOCK
EK-PRO
GPU WB AMP-Trinity RTX 4090 Ni+Inox

Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING YOUR GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
ZOTAC GAMING GeForce RTX 4090 AMP Extreme AIRO 7
CUTTING AND PLACING THERMAL PADS 8
CLEANING THE PCB 8
APPLYING THERMAL COMPOUND 9
ATTACHING THE WATER BLOCK 10
INSTALLING THE BACKPLATE 11
ATTACHING THE BACKPLATE 12
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 12
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 13
TESTING THE LOOP 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14

- 4 -
Screw size guide (1x) 103012
120 mm
24 mm
120 mm
24 mm
BOX CONTENTS
Zotac RTX Pro Backplate (1x)
106362
Screw M2.5 x 4 ax1 (12x)
9047
Thermal PAD F 1.0 mm - (120 x 16 mm)
(2x)
Thermal PAD F 1.5 mm - (120 x 16 mm)
(2x)
Thermal PAD F 2.0 mm - (120 x 16 mm)
(1x)
EK-Pro GPU WB AMP-Trinity RTX 4090 Ni+Inox
Thermal PAD G 0.5mm - (120 x 24 mm)
(2x)
Thermal PAD G 2.0 mm - (120 x 24 mm)
(2x)
120 mm
16 mm
120 mm
16 mm
120 mm
16 mm
Thermal Grizzly Hydronaut (1g)
(1x)
Screw M2.5 x 7 AX1 (10x)
9049
EK-Loop Multi Allen Key (6mm,
8mm, 9mm) (1x)

- 5 -
WATER BLOCK DIMENSIONS
247.4 mm
284 mm
70 mm
121.9 mm
151.9 mm
47.7 mm
76.7 mm
14.1 mm
23.8 mm

- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Position EAN Description Quantity
1106351 Coldplate (Nickel) 1
2106355 Top plate (Inox) 1
3106359 IO Bracket (Nickel) 1
4106133 Plexi insert 1
5103767 FC terminal Direct (Acetal) 1
6106362
Backplate (Bl. elox) 1
75155 Terminal OR 15 x 1 mm 2
8106360 Main OR Zotac RTX 4090 Pro 1
9106367 Inner OR 170 x 2 mm 1
10 10006 Screw M4 x 27 DIN7984 3
11 9049 Screw M2.5 x 7 AX1 10
12 9047 Screw M2.5 x 4 AX1 12
13 103089 Screw M3 x 5 ISO14581 TX Inox 29
14 106357 Standoff M3-M2.5 x 12.3 Brass (female) 3
15 103988 Standoff M4-M2.5 x 3 Brass 7
16 8541 Standoff M4-M2.5 x 6.6 Brass 4
2
16
12
4
14
3
1
15
9
6
13
7
10
8
11
5

- 7 -
STEP 1
PREPARING YOUR GRAPHICS CARD
Phillips Head Screwdriver
REMOVING THE STOCK COOLER
ZOTAC GAMING GeForce RTX 4090 AMP Extreme AIRO
STEP 1
Using a Philips-head screwdriver, unscrew marked screws to detach
the stock cooler and retention bracket from the GPU PCB. After
removing, carefully unplug all the LEDs and FANs cables.
For this step, you will need:
STEP 2
Phillips Head Screwdriver
STEP 2
From the front side of the GPU PCB, additional two (2) screws must
be unscrewed to remove the I/O Bracket from the GPU PCB. Lastly,
unscrew four (4) backplate screws. Remove the Backplate.
For this step, you will need:
RETENTION
BRACKET
I/O BRACKET
SCREWS
STOCK COOLER
BAC KP L ATE

- 8 -
STEP 3
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
STEP 3
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
120 mm
16 mm
1 mm
Thermal Pad F – 1.5 mm (120 x 16 mm)
1.5 mm
120 mm
16 mm
CUTTING AND PLACING THERMAL PADS
STEP 1
The GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
MOSFETs, and drivers.
Remove the protective foil from both sides of the thermal
pad before installation.
Replacement thermal pads:
Thermal Pad G 0.5 mm – (120 x 24 mm) EAN: 3830046996763
Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
Thermal Pad F 1.5 mm – (120 x 16 mm) EAN: 3830046996756
Thermal Pad G – 0.5 mm (120 x 24 mm)
120 mm
24 mm
0.5 mm

- 9 -
STEP 2
STEP 2
Once cut to the size, Thermal Pads should be placed on the
coldplate, as shown in the picture.
Thermal Grease
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
APPLYING THERMAL COMPOUND
For this step, you will need:
Thermal Pad - 120 x 16 x 1.0 mm
F1
Thermal Pad - 120 x 16 x 1.5 mm
F1.5
Thermal Pad - 120 x 24 x 0.5 mm
G0.5
F1
F1.5
F1.5
F1.5 F1.5
F1.5
F1.5
G0.5
G0.5
G0.5
G0.5
G0.5
G0.5
F1 F1
F1

- 10 -
ATTACHING THE WATER BLOCK
STEP 1
For this Step, you will need:
M2.5 x 4 AX1
Screw (8 pcs)
4 mm
STEP 2
M2.5 x 4 AX1 SCREW
STEP 2
Use eight (8) M2.5 x 4 AX1 Screws and tighten the PCB on the
water block. Tighten the screws evenly using the Philips-head
screwdriver. EK recommends you start tightening the screws
around the GPU core first and then continuing outwards to prevent
damage to the GPU.
Phillips Head
Screwdriver
STEP 1
Carefully position the water block with preinstalled standoffs on the
graphics card. During this process, make sure you have aligned the
mounting holes of the PCB with the holes of the water block.
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
Before attaching the PCB to the Water Block, make sure
all the Thermal Pads are placed correctly!