ekwb EK-Quantum Vector Trinity RTX 3080/3090 User manual

USER GUIDE
GPU WATER BLOCK
EK-Quantum
Vector Trinity RTX 3080/3090

Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
REQUIRED TOOLS 5
WATER BLOCK DIMENSIONS 5
WATER BLOCK SPECIFICATIONS AND MAIN PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
REMOVING THE I/O COVER 7
REMOVING THE STOCK BACKPLATE AND COOLER FRAME 8
CLEANING THE PCB 8
CUTTING AND PLACING THERMAL PADS 9
APPLYING THERMAL COMPOUND 10
INSTALLING THE WATER BLOCK 11
PLACING THE BLOCK ON THE GRAPHICS CARD 11
ATTACHING THE BLOCK TO THE GRAPHICS CARD 11
ATTACHING THE I/O COVER 12
CHECKING FOR CONTACT 12
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 13
INSTALLATION OF FITTINGS AND TUBING 13
CONNECTING THE D-RGB LED STRIP 14
TESTING THE LOOP 14
SUPPORT AND SERVICE 15
SOCIAL MEDIA 15

- 4 -
BOX CONTENTS
4 mm
4 mm
6 mm
8 mm
M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)
M2.5 Nut (2 pcs)
M2,5x6 AX1 Screw (13 pcs)
Allen Key 2.5. mm (1 pc)
Thermal Pad F 1.0 mm (4 pcs)
Thermal Grease (1 pc)
M2,5x8 AX1 Screw (2 pcs)
M2,5x4 AX1 Screw (16 pcs)
EK-Quantum Vector Trinity RTX 3080/3090 D-RGB M2.5 PVC Washers (16 pcs)
120 mm
16 mm
EK-Plug G1/4 (2 pcs)
Mounting mechanism - You may not need all the screws,
mounting mechanism is universal!

- 5 -
WATER BLOCK DIMENSIONS
231 mm
99 mm
113 mm
124 mm
92 mm
121 mm
14.5 mm
20.5 mm
Phillips Head Screwdriver Scissors
REQUIRED TOOLS

- 6 -
WATER BLOCK SPECIFICATIONS AND MAIN PARTS
Technical Specification:
- Dimensions (LxHxW): 231 x 124 x 20.5 mm
- D-RGB (Addressable RGB) Cable Length: 500 mm
- D-RGB LED Count: 5
- D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)
M4 x 8 DIN7984 SCREW
TOP PL ATE
(PLEXI / ACETAL)
M3,5/M2,5 x 12,6
STANDOFF
M4 x 27 DIN7984
SCREW
TERMINAL
(PLEXI / ACETAL)
O-RING 15x1
INSERT
COLDPLATE
(COPPER / NICKEL)
JE T PLATE
M3,5/M2,5 x 2,5 STANDOFF
M2,5x8 AX1
SCREW
M3,5/M2,5 x 6,6
STANDOFF
LED D-RGB STRIP
UNDER STANDOUT
(BLACK)
EK BADGE
STANDOUT (BLACK / WHITE)
O-RING 122X2

- 7 -
PREPARING THE GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Use the Phillips head screwdriver to remove the six marked screws
from the side of the backplate.
Carefully detach the PCB together with the backplate from the stock
cooler and disconnect four cables connected to the PCB.
Always remove the stock cooler slowly - it might be firmly
glued to the PCB with thermal pads.
You will need the following tool:
STEP 2
REMOVING THE I/O COVER
Use the Phillips head screwdriver to remove the two screws from the
side of the backplate and three screws from the I/O side. Put the I/O
cover aside - you’ll need it later.
STEP 1
STEP 2
Phillips Head Screwdriver

- 8 -
STEP 3
STEP 4
STEP 4
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB
STEP 3
REMOVING THE STOCK BACKPLATE AND COOLER
FRAME
Use the Phillips head screwdriver to remove the six screws and
carefully detach the stock cooler frame and stock backplate from
the PCB.
STOCK COOLER FRAME
STOCK BACKPLATE
Screws that are holding the backplate and frame to the PCB.

- 9 -
STEP 2
Trinity RTX™ 3080/3090 STEP 2
Once cut to size, thermal pads should be placed on the PCB, as
illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
STEP 1
Your GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
MOSFETs, and drivers.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal pads:
4x Thermal Pad F 1.0mm – (120X16mm) EAN: 3830046996732
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
CUTTING AND PLACING THERMAL PADS
120 mm
16 mm
1 mm
Thermal Pad F 1.0mm

- 10 -
Thermal Grease
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the CPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
STEP 1
APPLYING THERMAL COMPOUND
For this Step, you will need: