ekwb EK-Quantum Vector TUF RX 6800 User manual

USER GUIDE
GPU WATER BLOCK
EK-Quantum
Vector TUF RX 6800/6900

Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
REQUIRED TOOLS 5
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK BACKPLATE 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 8
CUTTING AND PLACING THERMAL PADS 9
APPLYING THERMAL COMPOUND 10
INSTALLING THE WATER BLOCK 10
PLACING THE BLOCK ON THE GRAPHICS CARD 10
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 11
ATTACHING THE WATER BLOCK 11
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12
INSTALLATION OF FITTINGS AND TUBING 12
CONNECTING THE D-RGB LED STRIP 13
TESTING THE LOOP 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14

- 4 -
BOX CONTENTS
4 mm
EK-Loop Multi Allen Key (1 pc)
M2.5 Nut (1 pc)
Allen Key 2 mm (1 pc)
Thermal Pad F 1.0 mm (4 pcs)
Thermal Grease (1 pc)
M2.5 x 4 AX1 Screw (30 pcs)
EK-Quantum Vector TUF RX 6800/6900 D-RGB
PVC Washer M2.5 (28 pcs)
120 mm
16 mm
Allen Key 2.5 mm (1 pc) EK-Plug G1/4 (2 pcs)
Universal Mounting Mechanism – You may not need every
screw from this package.

- 5 -
WATER BLOCK DIMENSIONS
300.5 mm
157.6 mm
142.2 mm
147 mm
176 mm
16.5 mm
Phillips Head Screwdriver Scissors
REQUIRED TOOLS

- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Technical Specification:
- Dimensions (L x H x W): 300.5 x 157.5 x 16.5 mm
- D-RGB (Addressable RGB) Cable - Length: 500 mm
- D-RGB LED Count: Plexi – 9 / Acetal – 9
- D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)
M4 x 8 DIN7984 SCREW
FC TERMINAL
M4 x 20 DIN7984 SCREW
TERMINAL COVER
TOP COVER STICKERS
TERMINAL O-RING 15 x 1 mm
COLDPLATE (NICKEL)
MAIN O-RING
JE T PL AT E
D-RGB LED STRIP
STANDOUT STANFOFF
STANDOUT
TOP PLATE (PLEXI, ACETAL)
M4/M2.5 x 6.60
STANDOFF
STANDOFF M4/M2.5 x 2.50

- 7 -
PREPARING THE GRAPHICS CARD
You will need the following tool:
Phillips Head Screwdriver
STEP 1
Place your graphics card on the flat surface and unscrew the eight
(8) red marked screws from the GPU Backplate using Phillips head
screwdriver. Carefully remove the Backplate from the GPU.
REMOVING THE STOCK BACKPLATE
STEP 1
BAC KP L ATE
REMOVING THE STOCK COOLER
STEP 1
After removing the backplate, unscrew the four (4) orange marked
retention bracket screws and two (2) blue marked stock cooler
screws. Also, two (2) green marked screws from the side of the I/O
Bracket needs to be removed. Carefully remove the retention bracket
and detach the PCB from the stock cooler. Disconnect all cables
connecting the stock cooler to the PCB.
Always remove the stock cooler slowly - it might be firmly
glued to the PCB with thermal pads.
STEP 1

- 8 -
STEP 2
STEP 2
Lastly, remove the green marked screw from the front side of the
PCB. The PCB is now ready for the water block installation.
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.

- 9 -
STEP 1
Your GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
MOSFETs, and drivers.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal pads:
4x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
CUTTING AND PLACING THERMAL PADS
120 mm
16 mm
1 mm
STEP 2
STEP 2
Once cut to size, thermal pads should be placed on the PCB, as
illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
Thermal Pad F 1.0mm

- 10 -
Thermal Grease
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
STEP 1
APPLYING THERMAL COMPOUND
For this Step, you will need:
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks.
Carefully position the water block with preinstalled standoffs on
the graphics card. During this process, make sure you have aligned
mounting holes of the PCB with holes of the water block (same
applies to other tops).
Pay attention not to use too much force when pressing the
block down to the PCB since chip dies are prone to cracking.
STEP 1