ekwb EK-QuantumX Loophole Distroplate D5 PWM User manual

USER GUIDE
DISTRIBUTION PLATE
EK-QuantumX
Loophole Distroplate D5 PWM

Please note the installation of the product is intended to be
undertaken by an adequately trained and experienced person. You
are installing the product at your own risk. If you are not properly
trained or experienced or feel unsure about the installation
procedure, please refrain from installing the product yourself and
contact our tech support for assistance. We disclaim our liability
for any damages to the product and incidental, consequential,
or indirect damages incurred due to improper or inappropriate
installation.
Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning the
installation process!
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of corrosion-inhibiting coolants is always recommended
for any liquid cooling system. EKWB recommends any of the
EKCryofuel for worry-free usage.
The warranty period is 24 months.

- 3 -
TABLE OF CONTENT
BOX CONTENTS 4
DISTRIBUTION PLATE DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
PREPARING THE DISTRIBUTION PLATE 8
INSTALLING THE FITTINGS AND TUBING 8
EXAMPLE OF A COOLING ROUTING 9
ATTACHING THE DISTRIBUTION PLATE 10
CONNECTING THE PUMP 11
TESTING THE LOOP 11
SUPPORT AND SERVICE 12
SOCIAL MEDIA 12

- 4 -
BOX CONTENTS
EK-QuantumX
Loophole Distroplate D5 PWM
Metal washer (8 pcs)
Allen Key 2.5 mm (1 pc)
Torx Key (1 pc)
Standoff Ø7.8/4 x 2.0 (8 pcs)
M4 x 10 DIN7984 Screw (8 pcs)
EK-Loop Multi Allen Key (1 pc)

- 5 -
DISTRIBUTION PLATE DIMENSIONS
140 mm
294 mm
71 mm
71 mm
28 mm
21 mm
42 mm 28 mm 21 mm21 mm
28 mm
40.5 mm
87 mm
46 mm

- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
8
7
5
2
10
4
12
6
11
3
Technical Specification:
EK-QuantumX Loophole Distroplate D5 PWM - Black
– Dimensions with the attached pump (W x D x H): 140 x 87 x 294 mm
– Reservoir volume: ~562 ml
– G1/4” ports: 34
– Plugs: 32 pieces with covers
– Frame: black anodized aluminum
– Pump cover: black anodized aluminum
Position EAN Description Quantity
1106932 TOP Plate - Block 1
2107062 D5 Pump cover (Bl. elox) 1
3106936 OR - 225 x 2 mm 1
4106931 TOP Plexi Insert 1
5106934 ALU Cover (Bl.elox) 1
6100663 EK - Badge 2
7102639 Quantum Plug 32
83831109834282 Plug Cover - Black 32
9105642 Screw M3 x 20 ISO 14581 TX –
INOX 14
10 3831109837597 EK-D5 PWM (12V SATA) 1
11 103311
D5 Cover Screw M4 x 62 mm Black 4
12 5154 OR 52 x 3 NBR50 1
9
1

- 7 -
8
7
5
2
10
4
12
6
11
3
Technical Specification:
EK-QuantumX Loophole Distroplate D5 PWM - Silver
– Dimensions with the attached pump (W x D x H): 140 x 87 x 294 mm
– Reservoir volume: ~562 ml
– G1/4” ports: 34
– Plugs: 32 pieces with covers
– Frame: silver anodized aluminum
– Pump cover: silver anodized aluminum
Position EAN Description Quantity
1106932 TOP Plate - Block 1
2107063 D5 Pump cover (Silver) 1
3106936 OR - 225 x 2 mm 1
4106931 TOP Plexi Insert 1
5106935 ALU cover (N.elox) 1
6100663 EK - Badge 2
7102639 Quantum Plug 32
83831109834282 Plug Cover - Black 32
9105642 Screw M3 x 20 ISO 14581 TX –
INOX 14
10 3831109837597 EK-D5 PWM (12V SATA) 1
11 103311
D5 Cover Screw M4 x 62 mm (Silver) 4
12 5154 OR 52 x 3 NBR50 1
9
1

- 8 -
PREPARING THE DISTRIBUTION PLATE
The distribution plate can be mounted on any 280 mm
(2 x 140 mm) mounting point, and with angled brackets
(sold separately), users can mount it 90° to a 120 mm or
140 mm fan mount.
The distribution plate does not have pre-prepared
channels for the coolant routing. Create the desired
configuration using micro 90° angle adaptors and HDP
or HDC connectors.
INSTALLING THE FITTINGS AND TUBING
STEP 1
Loosen the screws using Torx Key and remove the ALU Cover and
Plexi Insert from the distribution plate. Install the desired fitting
and tubing.
After attaching the fittings and tubing, reattach the Plexi insert and
ALU Cover.
When tightening the fittings and screws, make sure not
to apply too much force (Max 0.6Nm).
After the installation is complete, the distribution plate must
be checked for any potential leaks. Follow the EK-Loop Leak
Tester instructions for correct use:
https://www.ekwb.com/shop/EK-IM/EK-IM-3831109848388.pdf
STEP 1
M3 x 20 TX SCREW
ALU COVER
PLEXI INSERT

- 9 -
EXAMPLE OF A COOLING ROUTING

- 10 -
ATTACHING THE DISTRIBUTION PLATE
STEP 1
Find a suitable space in the chassis (140 mm fan patterns) and
carefully position the distribution plate. Make sure to align the
mounting holes with the holes in the chassis.
STEP 1
STEP 2
Use the mounting screws and washers to screw in the distribution
plate. When tightening, make sure not to apply too much force
(Max 0.6Nm).
STEP 2
M4 x 10 DIN7984
SCREW
M4 WASHER
For this step you will need:
M4 x 10 DIN7984 Screw Metal Washer Allen Key 2.5 mm

- 11 -
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
1. SATA Connector: It must be connected directly to your PSU at all
times as it is used to power the pump.
2. 4-pin PWM fan: It can be connected to your motherboard’s
CPU_ Fan or designated water pump header. It can also be
connected to a controller. This cable is used to control and report
the rotational speed of the pump. If it’s not connected, the pump
will run at maximum speed (100% PWM).
SATA
CONNECTOR
4-PIN PWM FAN
CONNECTOR
To make sure the installation of EK components was successful, we
recommend you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously. It is normal for the coolant level to drop during this
process as air collects in the distribution plate.
Inspect all parts of the loop, and in the eventuality that coolant leaks,
fix the issue and repeat the testing process. Ensure that all hardware is
dry before the system is powered on in order to prevent any damage.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the
EAN number of each part you might need.
Include the EAN number with quantity in your request.
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA