ekwb EK-MOSFET ASUS M6G Guide

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on August 12th 2013
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before
installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual before through before beginning with the installation process!
2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus VI GENE motherboard
STEP 2: PREPARING YOUR MOTHERBOARD
1. REMOVING STOCK COOLER.
Remove all encircled screws. There are 4 screws on the back of
the motherboard that needs to be removed in order to remove the factory installed MOSFET.
2. CLEANING THE PCB.
Carefully detach the original stock cooler after
removing all screws securing it to the board. Wipe off the remains (by
using non–abrasive cloth or
q-tip , as
shown on sample photo) of the
original thermal compound until the components and circuit board are
completely clean. EKWB recommends the use of denatured alcohol for
removing TIM leftovers.
4. CUTTING THERMAL PADS.
Your block comes with two thermal pads which needs to be trimmed in order to fit the voltage regulation area (VRM/MOSFET) on the
motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED!
Replacement thermal pads @ EKWB web shop:
Thermal PAD A 1.0mm - (100x16mm) [EAN: 3830046996626]
5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow (PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH
SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION). EK recommends using small drops of electrically non-conductive (for example: Arctic Cooling MX-2 ™,MX-4 ™ or
GELID GC-Extreme ™) thermal grease on each phase regulator (that is being covered with thermal pad; see picture below) in order to even further improve the thermal
performance of the EK-MOSFET ASUS M6G series water block.
Intel Z87 CHIPSET
CPU socket(LGA-1150)
Installation and mounting manual for EK-MOSFET ASUS M6G water block:
Place 1.0mm thick thermal pads in larger strips over
marked area
and make sure all mosfet chips are
covered.
Mosfets

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on August 12th 2013
STEP 3: PREPARING YOUR WATER BLOCK
1. PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-MOSFET ASUS M6G series water block with pre-installed 2.5mm standoffs kit gently to the motherboard or vice
versa. Make sure that mounting holes are aligned.
STEP 4: ATTACHING BLOCK TO MOTHERBOARD
STEP 5: CHECKING FOR CONTACTS
Prior to fastening the screws please make sure the mounting holes on the motherboard’s circuit board are
aligned with the water block.
Re-use ASUS factory (“stock”) backplate use four M3x8 DIN7985 and a PVC washer: Tighten the screws,
beginning near the center of the board and continue evenly outwards. Do not use excessive force when
tightening the screws!
Temporarily r emove the water block to check for uniform surface
contact between the block and the components. Note the pattern
of contact on a piece of paper. Then repeat steps 3 and 4 to
reattach the block applying more or less pressure to the areas
where you have found it necessary. Note that there is no need for
perfect thermal pad imprint on the inductors/coils (mentioned in
STEP2)
6. POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT
Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC compression fittings with the EK-MOSFET ASUS M6G
series water block. You can use any opening as an inlet/outlet port. Plan your tubing routing in advance!
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver
EK-PSC fitting
Tubing
PVC washer
Thermal pad imprints
M3x8 screw
ASUS factory backplate
M3 NUT
Detail A (Back of
the PCB)
Detail A (Top of the
PCB)